Crystallization evaporative crystallizer

Classification of batch crystallizers and batch crystallization operations according to the means by which supersaturation is created is still a widely accepted method. Therefore, the discussion of such operations may include cooling crystallization, evaporative crystallization, vacuum crystallization, antisolvent crystallization, reaction (reactive) crystallization, etc. The vacuum crystallization operation can be considered as a combination of the evaporative and cooling crystallization and thus will not be discussed separately. Reaction crystallization (precipitation) is discussed in detail in Chapter 6. 

Bikerman [179] has argued that the Kelvin equation should not apply to crystals, that is, in terms of increased vapor pressure or solubility of small crystals. The reasoning is that perfect crystals of whatever size will consist of plane facets whose radius of curvature is therefore infinite. On a molecular scale, it is argued that local condensation-evaporation equilibrium on a crystal plane should not be affected by the extent of the plane, that is, the crystal size, since molecular forces are short range. This conclusion is contrary to that in Section VII-2C. Discuss the situation. The derivation of the Kelvin equation in Ref. 180 is helpful. 

Most fiindamental surface science investigations employ single-crystal samples cut along a low-index plane. The single-crystal surface is prepared to be nearly atomically flat. The surface may also be modified in vacuum. For example, it may be exposed to a gas that adsorbs (sticks) to the surface, or a film can be grown onto a sample by evaporation of material. In addition to single-crystal surfaces, many researchers have investigated vicinal, i.e. stepped, surfaces as well as the surfaces of polycrystalline and disordered materials. 

The solution obtained is evaporated somewhat, cooled in a vacuum desiccator and the crystals of the tetraoxo-acid filtered off too drastic evaporation causes formation of the heptaoxodiphosphoric acid by loss of water. 

Evaporation and crystallisation of the sodium sulphite solution gives crystals of the heptahydrate NajSOj.THjO. However, on evaporation of the hydrogensulphite solution, the solid obtained is chiefly sodium pentaoxodisulphate(IV) ( metabisulphite ) Na2S20j, and contains little if any of the hydrogensulphite. However, the hydrogen sulphite ion is obtained when the solid redissolves in water ... 

The plate is removed from the tank, the position of the solvent front marked, and the solvent allowed to evaporate from the plate. If the components of the mixture are coloured, the separation is obvious if colourless, they must be located either by viewing under U.. or by standing the plate in a closed dry tank containing crystals of iodine, whose vapour makes brown spots show i p. 

Hydrolysis of Potassium Ethyl Sulphate. Dissolve about i g. of the crystals in about 4 ml. of cold distilled water, and divide the solution into two portions, a) To one portion, add barium chloride solution. If pure potassium ethyl sulphate were used, no precipitate should now form, as barium ethyl sulphate is soluble in water. Actually however, almost all samples of potassium ethyl sulphate contain traces of potassium hydrogen sulphate formed by slight hydrolysis of the ethyl compound during the evaporation of its solution, and barium chloride almost invariably gives a faint precipitate of barium sulphate. b) To the second portion, add 2-3 drops of concentrated hydrochloric acid, and boil the mixture gently for about one minute. Cool, add distilled water if necessary until the solution has its former volume, and then add barium chloride as before. A markedly heavier precipitate of barium sulphate separates. The hydrolysis of the potassium ethyl sulphate is hastened considerably by the presence of the free acid Caustic alkalis have a similar, but not quite so rapid an effect. 

To prepare a sample of the hydrochloride, add 0-5 ml. of the base to 10 ml, of dilute hydrochloric acid in an evaporating basin and evaporate to dryness, preferably in a vacuum desiccator. Recrystallise the dry residue from petroleum (b.p. 60-80°). The hydrochloride separates as white crystals, m.p. 90°. 

Mix I ml. of benzaldehyde and i ml. of aniline in a small evaporating-basin, place the latter on a boiling water-bath and stir the mixture gently with a glass rod. Globules of water soon appear on the oily layer. After about 20 minutes place the basin in ice-water, and stir the contents well, whereupon solidification should rapidly occur. (If the material does not solidify, replace the basin on the boiling water-bath for a further 10 minutes.) Break up the solid material in the basin, transfer to a conical flask, and recrystallise from rectified spirit. The benzylidene-aniline is obtained as colourless crystals, m.p, 52° yield, o-8 g. 

It is frequently necessary to concentrate a filtrate in order to obtain a further crop of crystals, or it may be necessary to concentrate a solution to a smaller volume. If the solvent is water and the substance is not volatile in steam, simple evaporation on a large dish on a steam or water... 

Cuprous bromide. The solid salt may be prepared by dissolving 150 g. of copper sulphate crystals and 87 5 g. of sodium bromide dihydrate in 500 ml. of warm water, and then adding 38 g. of powdered sodium sulphite over a period of 5-10 minutes to the stirred solution. If the blue colour is not completely discharged, a little more sodium sulphite should be added. The mixture is then cooled, the precipitate is collected in a Buchner funnel, washed twice with water containing a little dissolved sulphurous acid, pressed with a glass stopper to remove most of the liquid, and then dried in an evaporating dish or in an air oven at 100 120°. The yield is about 80 g. 

Mix 42 5 g. of acetone cyanohydrin (Section 111,75) and 75 g. of freshly powdered ammonium carbonate in a small beaker, warm the mixture on a water bath FUME CUPBOARD) and stir with a thermometer. Gentle action commences at 50° and continues during about 3 hours at 70-80°. To complete the reaction, raise the temperature to 90° and maintain it at this point until the mixture is quiescent (ca. 30 minutes). The colourless (or pale yellow) residue solidifies on coohng. Dissolve it in 60 ml. of hot water, digest with a little decolourising carbon, and filter rapidly through a pre-heated Buchner funnel. Evaporate the filtrate on a hot plate until crystals appear on the surface of the liquid, and then cool in ice. Filter off the white crystals with suction, drain well, and then wash twice with 4 ml. portions of ether this crop of crystals of dimethylhydantoin is almost pure and melts at 176°. Concentrate the mother liquor to the crj staUisation point, cool in ice, and collect the... 

Nicotinamide. Place 50 g. of pure ethyl nicotinate (Section V,23) in a 350 ml. bolt-head flask and add 75 ml. of concentrated aqueous ammonia saturated at 0°. Keep the flask loosely stoppered for 18 hours, after w)iich time the lower layer generally dissolves on shaking. Saturate the solution with ammonia and allow it to stand for a further 4 hours. Repeat the saturation with ammonia crystals of the amide commence to appear in the solution. Evaporate to drjmess in a dish on the steam bath and dry at 120°. The yield of nicotinamide, m.p. 130°, is usuallj quantitative. 

A suspension of 3.90 g (19.6 mmol) of p-(bromomethyl)benzaldehyde (2.8) and 4.00 g (31.7 mmol) of sodium sulfite in 40 ml of water was refluxed for two hours, after which a clear solution was obtained. The reaction mixture was cooled on an ice bath resulting in precipitation of some sodium sulfite. After filtration, the solvent was evaporated. Ethanol was added to the remaining solid and the suspension was refluxed for 10 minutes. After filtering the hot solution, the filtrate was allowed to cool down slowly to -18 °C whereupon sodium (p-oxomethylphenyl)methylsulfonate (2.9) separated as colourless crystals. The extraction procedure was repeated two more times, affording 2.29 g (10.3 mmol, 53%) of the desired product. H-NMR (200 MH D2O) 5(ppm) =4.10 (s,2H) 7.44 (d,2H) 7,76 (d,2H) 9.75 (s,lH). 

For the HCI salt Do exactly as above except use 6N Hydrochloric Acid. 6N HCI may be produced by diluting 60.4mL of "Muriatic Acid" to lOOmL with distilled water. Evaporate the bubbler solution to dryness then add 15ml of water, lOmL 10% NaOH soln. and heat gently to a boil with constant motion until dense white fumes appear. This will remove the Ammonium Chloride. Remove from heat while stirring as it cools down. Pulverize the dry residue, then reflux with absolute Ethanol for several minutes. Filter the refluxed soln. on a heated Buchner or Hirsch funnel, then distill the alcohol off the filtrate until crystals just begin to form. Allow the soln. to cool naturally to room temperature, then cool further in an ice bath. Filter the solution on a chilled Buchner funnel with suction. The yield of Meth iamine Hydrochloride should be around 55% of the theoretical. 

Transfer the filtrate to a ceramic evaporating dish and heat on a water bath until a crystalline scum forms on the top. Cool the dish quickly then filter the mess on the vacuum Buchner to yield 96g of Methylamine Hydrochloride. Concentrate the filtrate once again to obtain a second crop of crystals, -IQg. Concentrate the filtrate a third time as far as possible using the water bath, then store the dish in a vacuum dessicator loaded with Sodium Hydroxide in the bottom for 24 hours. Add Chloroform to the residue left in the crucible to dissolve out Dimethylamine Hydrochloride (distill off the Chloroform to recover - good stuff) then filter on the venerable old vacuum Buchner funnel to yield an additional 20g of Methylamine Hydrochloride, washing the crystals in the funnel with a small poiiion of Chloroform ( 10mL). 

Evaporate the beaker contents to dryness on a glass plate In the oven to collect the crystals of Methylamine HCI (hygroscopic ). The yield should be approximately 15g (95%). 

---