Crystal zinc compounds

Dialkyl zinc compounds form phosphine complexes of formula RZnP(SiMe3)2 on addition of one equivalent of bis(trimethylsilyl)phosphine. Solution and solid-state studies showed that the complexes are dimeric or trimeric in solution or the solid state. Bis(trimethylsilyl)phosphido-methylzinc crystallizes as a trimeric molecule with a Zn3P3 core in the twist-boat conformation. Bis(trimethylsilyl)phosphido- -butylzinc, shows a similar central Zn3P3 fragment. The sterically more demanding trimethylsilylmethyl substituent forms a dimeric species of bis(trimethylsilyl) phosphido-trimethylsilylmethylzinc. Solution studies of bis(trimethylsilyl)phosphido- .vo-propyl-zinc demonstrate a temperature-dependent equilibrium of the dimeric and trimeric species and the crystalline state contains a 1 1 mixture of these two oligomers. A monomeric bis(trimethyl-silyl)phosphido-tris(trimethylsilyl)methylzinc has also been synthesized.313... 

The presence of triethylenetetramine in the hydrothermal synthesis of open-framework zinc phosphates results in a number of frameworks with one- to three-dimensional structures. The structures include one-dimensional ladders, two-dimensional layer structures, and one structure where the tetramine is bound to the zinc center. The structural type was highly sensitive to the relative concentration of the amine and phosphoric acid.411 Piperazine and 2-methylpiperazine can be used as templating molecules in solvothermal syntheses of zinc phosphates. The crystallization processes of the zinc compounds were investigated by real time in situ measurements of synchrotron X-ray powder diffraction patterns.412... 

Many studies on the direct reaction of methyl chloride with silicon-copper contact mass and other metal promoters added to the silicon-copper contact mass have focused on the reaction mechanisms.7,8 The reaction rate and the selectivity for dimethyldichlorosilane in this direct synthesis are influenced by metal additives, known as promoters, in low concentration. Aluminum, antimony, arsenic, bismuth, mercury, phosphorus, phosphine compounds34 and their metal complexes,35,36 Zinc,37 39 tin38-40 etc. are known to have beneficial effects as promoters for dimethyldichlorosilane formation.7,8 Promoters are not themselves good catalysts for the direct reaction at temperatures < 350 °C,6,8 but require the presence of copper to be effective. When zinc metal or zinc compounds (0.03-0.75 wt%) were added to silicon-copper contact mass, the reaction rate was potentiated and the selectivity of dimethyldichlorosilane was enhanced further.34 These materials are described as structural promoters because they alter the surface enrichment of silicon, increase the electron density of the surface of the catalyst modify the crystal structure of the copper-silicon solid phase, and affect the absorption of methyl chloride on the catalyst surface and the activation energy for the formation of dimethyldichlorosilane.38,39 Cadmium is also a structural promoter for this reaction, but cadmium presents serious toxicity problems in industrial use on a large scale.41,42 Other metals such as arsenic, mercury, etc. are also restricted because of such toxicity problems. In the direct reaction of methyl chloride, tin in... 

Zinc Chromite, ZnO.CraOg, may be obtained in the same manner as the corresponding calcium salt. It yields dark green octahedral crystals of density 5 29 at 13° C. Two other zinc compounds are known, namely 3Zn0.2Cr20j eZnO.SCrgOg. 

The colorless zinc compound, Zn(CisH6)2, which sublimes at 160° under partial decomposition, is obtained in small yield from zinc chloride and cyclopentadienyl sodium in diethyl ether however, the less stable cadmium compound decomposes, with separation of cadmium, under these conditions (55). The mercury compound, Hg(CsH5)2, is produced in 20% yield by the action of the sodium derivative on mercuric chloride in tetrahydrofuran (215). The action of cyclopentadiene on the complex K2(HgI ) in aqueous alkaline solution results in the precipitation of a mixture of CsHsHgl and Hg(CsH6)2, from which the latter compound may be obtained in good yield by extraction with a mixture of tetrahydrofuran and petroleum ether (62). It forms pale yellow crystals which begin to decompose at about 60° and which melt at 83-85°. The compound is readily soluble in most solvents it decomposes slowly even when kept in the dark at room temperature it is insoluble in water and reacts with neither water nor bases. On the other hand, decomposition occurs in dilute hydrochloric acid. It converts ferric chloride to ferrocene quantitatively, and it yields an adduct with maleic anhydride (215). 

Stabilizers are almost invariably added to PVC to improve its heat and light stability. The species found effective in stabilizing PVC are those that are able to absorb or neutralize HCl, react with free radicals, react with double bonds, or neutralize other species that might accelerate degradation. Lead compounds, such as basic lead carbonate and tribasic lead sulfate, and metal soaps of barium, cadmium, lead, zinc, and calcium are used as stabilizers. Obviously, they can react with HCl. Epoxy plasticizers aid in stabilizing the resin. Another group of stabilizers are the organotin compounds, which find application because of their resistance to sulfur and because they can yield crystal-clear compounds. 

Table 4.1-149 Electro-optical constants of zinc compounds. Under the influence of an electric field, the refractive index changes in accordance to the nonlinearity of the dielectric polarization (Pockels effect). Crystals with hexagonal symmetry have three electro-optical constants rsi, 733, 751 crystals with cubic symmetry have only one electro-optical constant 741...

Method of forming zinc oxide light-shielding film for liquid crystals shields includes the injection of vapors of alkyl zinc compound with ozone or atomic oxygen in the activation chamber after which they pass through a chamber for ZnO film deposition at low temperature heating at about 200°C. The method is applicable for large-scale production of these films... 

Carry out this preparation precisely as described for the a-compound, but instead of zinc chloride add 2 5 g. of anhydrous powdered sodium acetate (preparation, p. 116) to the acetic anhydride. When this mixture has been heated on the water-bath for 5 minutes, and the greater part of the acetate has dissolved, add the 5 g. of powdered glucose. After heating for I hour, pour into cold water as before. The viscous oil crystallises more readily than that obtained in the preparation of the a-compound. Filter the solid material at the pump, breaking up any lumps as before, wash thoroughly with water and drain. (Yield of crude product, io o-io 5 g.). Recrystallise from rectified spirit until the pure -pentacetylglucose is obtained as colourless crystals, m.p- 130-131° again two recrystallisations are usually sufficient for this purpose. 

---