Crystal strength

Chapters 2 and 3 contain discussion on the theoretical foundations of hardness. The extensive classical theory of crystal strength has been omitted intentionally, since this subject is covered in most monographs within the scope of solid body physics and chemistry. Chapter 3 is based on the study of Povarennykh (1963), Hardness of Minerals, which most appropriately emphasizes the elements of the crystallomechanical theory of hardness that specifically find application in practice. 

Melting temperature (Tin) 137 C folded chain crystals strength properties derived from crystallinity low thermal resistance. Extended chain crystals can melt at about 145°C... 

The structure of compression molded samples is more uniform than the injection molded bars, so the cavitation occurs across the gauge of the sample. The presence of cavitation in those samples depends on the strain rate. If the deformation is slow, then the crystalline elements are able to deform plastically before reaching the cavitation threshold of the amorphous phase. When the strain rate is higher, the yield stress, related to crystal strength, is higher (38-38.5 MPa) and cavitation occurs first. 

Most solid surfaces are marred by small cracks, and it appears clear that it is often because of the presence of such surface imperfections that observed tensile strengths fall below the theoretical ones. For sodium chloride, the theoretical tensile strength is about 200 kg/mm [136], while that calculated from the work of cohesion would be 40 kg/mm [137], and actual breaking stresses are a hundreth or a thousandth of this, depending on the surface condition and crystal size. Coating the salt crystals with a saturated solution, causing surface deposition of small crystals to occur, resulted in a much lower tensile strength but not if the solution contained some urea. 

Rehbinder and co-workers were pioneers in the study of environmental effects on the strength of solids [144], As discussed by Frumkin and others [143-145], the measured hardness of a metal immersed in an electrolyte solution varies with applied potential in the manner of an electrocapillary curve (see Section V-7). A dramatic demonstration of this so-called Rehbinder effect is the easy deformation of single crystals of tin and of zinc if the surface is coated with an oleic acid monolayer [144]. 

A number of substances such as graphite, talc, and molybdenum disulfide have sheetlike crystal structures, and it might be supposed that the shear strength along such layers would be small and hence the coefficient of friction. It is true... 

Discuss the types of bonding that hold atoms and ions together in molecules and crystals. Include in your answer evidence for the existence of the bonds that you describe, and some indication of their relative strength. 

Secondly, the ultimate properties of polymers are of continuous interest. Ultimate properties are the properties of ideal, defect free, structures. So far, for polymer crystals the ultimate elastic modulus and the ultimate tensile strength have not been calculated at an appropriate level. In particular, convergence as a function of basis set size has not been demonstrated, and most calculations have been applied to a single isolated chain rather than a three-dimensional polymer crystal. Using the Car-Parrinello method, we have been able to achieve basis set convergence for the elastic modulus of a three-dimensional infinite polyethylene crystal. These results will also be fliscussed. 

The resin has the ability to be oriented by a drawing process and crystallized to yield a high-strength product. 

Testing. Chemical analyses are done on all manufactured abrasives, as well as physical tests such as sieve analyses, specific gravity, impact strength, and loose poured density (a rough measure of particle shape). Special abrasives such as sintered sol—gel aluminas require more sophisticated tests such as electron microscope measurement of a-alumina crystal si2e, and indentation microhardness. 

At HOY speeds, the rate of increase in orientation levels off but the rate of crystallization increases dramatically. Air drag and inertial contributions to the threadline stress become large. Under these conditions, crystallization occurs very rapidly over a small filament length and a phenomenon called neck-draw occurs (68,75,76). The molecular stmcture is stable, fiber tensde strength is adequate for many uses, thermal shrinkage is low, and dye rates are higher than traditional slow speed spun, drawn, and heat-set products (77). 

Polyester sheet products may be produced from amorphous poly(ethylene terephalate) (PET) or partiaHy crystallized PET. Acid-modified (PETA) and glycol modified (PETG) resins are used to make ultraclear sheet for packaging. Poly(butylene terephthalate) (PBT) has also been used in sheet form. Liquid-crystal polyester resins are recent entries into the market for specialty sheet. They exhibit great strength, dimensional stabHity, and inertness at temperatures above 250°C (see Polyesters,thermoplastic). 

Weathering. Articles fabricated from FEP are unaffected by weather, and thek resistance to extreme heat, cold, and uv kradiation suits them for apphcations in radar and other electronic components. For example, after 15 years of solar exposure in Florida, the tensile strength (73) and light transmission (96%) of a 25-p.m thick film was unchanged and the film remained crystal clear. Elongation increased slightly for the first 5 to 7 years of outdoor exposure, probably as a result of stress relaxation. Beyond 10 years, a small decrease was observed. 

Finally, the nature of the crystalline microstmcture, ie, crystal size and morphology and the textural relationship among the crystals and glass, is the key to many mechanical and optical properties, including transparency/opacity, strength and fracture toughness, and machinabiUty. These microstmctures can be quite complex and often are distinct from conventional ceramic microstmctures (6). 

---