Copolymer compatibility

There is no homogenization by third copolymers compatible with each of the mixture components. 

It is made by emulsion polymerization, spray-dried and sold as a fine particle powder. Pigment and fluoropolymer particles are separately dispersed in a solution of an acrylic copolymer compatible with PVdF, the two dispersions being blended to give the final paint. After application of paint, the coil is heated to 240-260 °C in 30-60 s, when the PVdF particles melt and lose their identify, forming a blend with the acrylic. 

Heterogeneous alloys can be formed when graft or block copolymers are combined with a compatible polymer. Alloys of incompatible polymers can be formed if an interfacial agent can be found. 

The formation of copolymers involves the reaction of (at least) two kinds of monomers. This means that each must be capable of undergoing the same propagation reaction, but is is apparent that quite a range of reactivities is compatible with this broad requirement. We shall examine such things as the polarity of monomers, the degree of resonance stabilization they possess and the steric... 

Unlike most crystalline polymers, PVDF exhibits thermodynamic compatibiUty with other polymers (133). Blends of PVDF and poly(methyl methacrylate) (PMMA) are compatible over a wide range of blend composition (134,135). SoHd-state nmr studies showed that isotactic PMMA is more miscible with PVDF than atactic and syndiotactic PMMA (136). MiscibiUty of PVDF and poly(alkyl acrylates) depends on a specific interaction between PVDF and oxygen within the acrylate and the effect of this interaction is diminished as the hydrocarbon content of the ester is increased (137). Strong dipolar interactions are important to achieve miscibility with poly(vinyhdene fluoride) (138). PVDF blends are the object of many papers and patents specific blends of PVDF and acryflc copolymers have seen large commercial use. 

Hydrocarbon resins (qv) are prepared by copolymerization of vinyltoluene, styrene, and a-methylstyrene in the presence of a Eriedel-Crafts catalyst (AlCl ). These resins are compatible with wax and ethylene—vinyl acetate copolymer (197). 

Styrenic block copolymers (SBCs) are also widely used in HMA and PSA appHcations. Most hot melt appHed pressure sensitive adhesives are based on triblock copolymers consisting of SIS or SBS combinations (S = styrene, I = isoprene B = butadiene). Pressure sensitive adhesives typically employ low styrene, high molecular weight SIS polymers while hot melt adhesives usually use higher styrene, lower molecular weight SBCs. Resins compatible with the mid-block of an SBC improves tack properties those compatible with the end blocks control melt viscosity and temperature performance. 

CPA. Copolymer alloy membranes (CPAs) are made by alloying high molecular weight polymeries, plasticizers, special stabilizers, biocides, and antioxidants with poly(vinyl chloride) (PVC). The membrane is typically reinforced with polyester and comes in finished thicknesses of 0.75—1.5 mm and widths of 1.5—1.8 m. The primary installation method is mechanically fastened, but some fully adhered systems are also possible. The CPA membranes can exhibit long-term flexibiHty by alleviating migration of the polymeric plasticizers, and are chemically resistant and compatible with many oils and greases, animal fats, asphalt, and coal-tar pitch. The physical characteristics of a CPA membrane have been described (15). 

Poly(ethyl methacrylate) (PEMA) yields truly compatible blends with poly(vinyl acetate) up to 20% PEMA concentration (133). Synergistic improvement in material properties was observed. Poly(ethylene oxide) forms compatible homogeneous blends with poly(vinyl acetate) (134). The T of the blends and the crystaUizabiUty of the PEO depend on the composition. The miscibility window of poly(vinyl acetate) and its copolymers with alkyl acrylates can be broadened through the incorporation of acryUc acid as a third component (135). A description of compatible and incompatible blends of poly(vinyl acetate) and other copolymers has been compiled (136). Blends of poly(vinyl acetate) copolymers with urethanes can provide improved heat resistance to the product providing reduced creep rates in adhesives used for vinyl laminating (137). 

Speciali2ed copolymer latices, which are inherently and permanently tacky, are available as pressure-sensitive emulsions. They are mechanically stable and have excellent machinabiUty. They are compatible with many other PVAc latices and, therefore, can be easily blended with other resins for modification of surface tack, peel strength, and creep. 

Polyacrjiates (3), where R = H, CH n < 100, 000 and Y = OH, OCH, O, etc, or copolymers with compatible monomers, are probably the most flexible dispersant products, because they are produced in a variety of molecular weights and degrees of anionic charge. Moreover, reaction of acryflc acid with other monomers confers additional properties that make them more adaptable for niche appHcations. 

Polymaleates (4), where n < 100, 000 and Y = OH, 0 , or copolymers with compatible monomers such as styrene, acryflc acid, etc, generally show... 

Adhesives, Coatings, and Sealants. Eor these appHcations, styrenic block copolymers must be compounded with resins and oils (Table 10) to obtain the desired properties (56—58). Materials compatible with the elastomer segments soften the final product and give tack, whereas materials compatible with the polystyrene segments impart hardness. The latter are usually styrenic resins with relatively high softening points. Materials with low softening points are to be avoided, as are aromatic oils, since they plasticize the polystyrene domains and reduce the upper service temperature of the final products. 

In the early stages of development of polypropylene rubbers, particularly butyl rubber, were used to reduce the brittleness of polypropylene. Their use declined for some years with the development of the polypropylene copolymers but interest was greatly renewed in the 1970s. This interest has been centred largely around the ethylene-propylene rubbers which are reasonably compatible in all proportions with polypropylene. At first the main interest was with blends in which the rubber content exceeded 50% of the blend and such materials have been designated as thermoplastic polyolefin elastomers (discussed in Section 11.9.1). There is also increasing interest in compounds with less than 50% rubber, often referred to as elastomer-modified thermoplastics. It is of interest to note... 

The anomalous effect of the last two rubbers in the table with their low solubility parameters is possibly explained by specific interaction of PVC with carbonyl and carboxyl groups present respectively in the ketone- and fumarate-containing rubbers to give a more than expected measure of compatibility. It is important to note that variation of the monomer ratios in the copolymers and terpolymers by causing changes in the solubility parameter and eompatibility will result in variation in their effect on impact strength. 

In addition to acting as impact modifiers a number of polymeric additives may be considered as processing aids. These have similar chemical constitutions to the impact modifiers and include ABS, MBS, chlorinated polyethylene, acrylate-methacrylate copolymers and EVA-PVC grafts. Such materials are more compatible with the PVC and are primarily included to ensure more uniform flow and hence improve surface finish. They may also increase gelation rates. In the case of the compatible MBS polymers they have the special function already mentioned of balancing the refractive indices of the continuous and disperse phases of impact-modified compound. 

The earliest SIS block copolymers used in PSAs were nominally 15 wt% styrene, with an overall molecular weight on the order of 200,000 Da. The preparation by living anionic polymerization starts with the formation of polystyryl lithium, followed by isoprene addition to form the diblock anion, which is then coupled with a difunctional agent, such as 1,2-dibromoethane to form the triblock (Fig. 5a, path i). Some diblock material is inherently present in the final polymer due to inefficient coupling. The diblock is compatible with the triblock and acts... 

New copolymers based on a copolymerization of isobutylene and p-methyl-styrene with improved heat resistance have been reported [64]. Once copolymerization was accomplished, the polymer was selectively brominated in the p-methyl position to yield a terpolymer called EXXPO. In contrast to butyl and halobutyl, the new terpolymer has no unsaturation in the backbone and therefore shows enhanced thermal stability and resistance to oxidation. Useful solvent-based adhesives can be formulated using the new terpolymer in combination with block copolymers [65]. The hydrocarbon nature of the new terpolymer results in excellent compatibility with hydrocarbon resins and oils. 

There is increasing interest in copolymer systems, which, due to their chemical heterogeneity, may require very complex eluent systems in order to dissolve the sample and ensure that the separation ensues hy a pure size exclusion mechanism. In these examples, the PLgel is also compatible with eluent systems containing mixed solvents of different polarity (including water as a cosolvent up to 10% hy volume) and in organic solvents modified with acids or bases (e.g., acetic or formic acid, triethanolamine) as it is stable in the pH range of 1-14. 

---