Combining tools

Christensen-Mason Jar. (See Figure 4-172 and Table 4-103 [57].) This is a combination tool, offering possibility to jar upwards hydraulically and to bump downward mechanically. The jar is equipped with a special releasing (locking) mechanism, so that the jar cannot be fired upwards until the locking system has been released. It has a 6-in. jarring stroke upwards and 30-in. for downward bumping [57]. 

The use of LC as a sample pretreatment of GC has received considerable attention. The separation mechanisms in LC and GC are complementary, providing a powerful combined tool for the separation of complex... 

Finally, we mention two methods for de novo library design. Caflisch168 applied the MCSS169 technique generating fragment placements, which are subsequently connected. The DREAM++ software combines tools for fragment placement and selection.170 The selection process is done such that only a small set of well-characterized organic reactions is needed to create the library. 

These analyses and associated experiments demonstrate that fracture mechanics can be used to provide information and insight into the value of the failure load, the locus of likely crack growth, and the path along which the crack will then grow. Where analytical analyses of stress, strain, and energy release rates are difficult or impossible, modern numerical methods can be very useful. In the opinion of the authors, the utility of these combined tools has hardly been exploited. The inclusion of nonlinear, nonelastic effects in the analyses is feasible is such materials are carefully characterized and/or properties become available. 

Combining Tools We use different hand tools during combining processes. We use screwdrivers to install and remove screws. Screwdrivers have tips that match the type of screw on which they are used. We use slotted screwdrivers on slotted-head screws and the Phillips screwdriver on Phillips head screws. Some screws have square drives, hex drives, or torx drives. Figure 8-19 shows various types of screwdrivers. It is important to select the appropriate size and type of screwdriver when installing or removing a screw. 

Zhou, C., Qi, K., Wooley, K.L., Walker, A.V. (2008) Time-of-flight secondary ion mass spectrometry, fluorescence microscopy and scanning electron microscopy combined tools for monitoring the process of pattering and layer-by-layer assembly of synthetic and biological materials. Colloids Surf. B Biointerfaces, 65(1), 85-91. 

Vibrational spectra and structure of clay mineral kaolinite have been investigated by the interplay between spectroscopy (IR/Raman) and quantum mechanical calculations (HF and MP2 calculations with 6-31IG basis sets) (77). Expai-mental and theoretical methods proved to be valuable combination tools for exploring the structure and dynamics of complex clay mineral structure. Their force field (potential) developed is also expected to be helpful in predictions and in interpretation of vibrational spectra of other clay minerals. Their quantum mechanically derived force-field parameters can be applied to MD simulations and vibrational normal mode analysis. 

Switch the combination cutting tool from the pilot drilling mode to the cutting mode by applying air pressure to a fitting on the combination tool and observing the position of a 1-in. steel pin (refer to manufacturer s instructions). 

When used by employees having a combined tool and body weight of 310 pounds, the criteria and protocols must be modified appropriately to provide proper protection for such heavier weights. 

Mali G, Meden A et al (2010) Li-6 MAS NMR spectroscopy and first-principles calculations as a combined tool for the investigation of Li2MnSi04 polymorphs. Chem Commun 46 3306-3308... 

In order that the full clinical potential of these IR techniques be realised, the strengths and limitations of the combined techniques approach must be examined in order to establish the reliability of the quantitative data generated. In this paper we outline our results using the combined tool of IR and multivariate techniques to develop a model to predict PG content in bovine cartilage sections by EDX and absorbance photo-microscopy. 

To determine appropriate pattern bases, Hanson and Crutchfield combined tools from computation theory and from nonlinear dynamics. Computation theory comes in because Hanson and Crutchfield define pattern bases in terms of formal languages and their corresponding automata. For example, ECA 18 has a single pattern basis Ai8 = (OS). That is, every other site is a zero the remaining sites can be either 0 or 1. (Such a formal-language description of a set of configurations could possibly be discovered automatically via a machine reconstruction algorithm, Crutchfield, 1994). 

---