Coateric

Figure Bl.17.8. Iron oxide particles coated with 4 nm of Pt in an m-planar magnetron sputter coater (Hennann and Mtiller 1991). Micrographs were taken in a Hitachi S-900 in-lens field emission SEM at 30,000 primary magnification and an acceleration voltage of 30 kV. Image width is 2163 nm.

Lay-up proceeds by laying down the veneer which is to be the back surface of the panel. Then a sufficient number of pieces of core veneer are passed through the glue spreader to form the next layer of cross-oriented veneer. The glue spreader commonly used in hardwood plywood manufacture is a roU coater in which a pair of opposing mbber roUs are coated with a thin layer of adhesive. As the veneer is passed between the roUs, the adhesive is transferred to the surfaces of the veneer. Adhesive is appHed only to the cross-pfles and in sufficient quantity to provide a continuous layer on both opposing faces of veneer. Thus, in the case of a three-ply panel, only the core layer is spread with adhesive and in that of a five-ply panel, the second and fourth layers both of which are cross-pfles, are spread with adhesive. Then the top surface veneer, which is normally the decorative surface, is placed on the assembly. 

In the automated lay-up system, each layer of veneer (with exception of the top surface veneer) passes under an automatic adhesive appHcation system. This may be a spray appHcation, a curtain coater, or an extmder, each of which is designed to apply a uniform adhesive spread on the upper face of each veneer. After all except the top veneer have been spread with adhesive and laid together, the top veneer is added. The me of the veneer—adhesive assembly at this point should be about 8%. 

Successful />Xylylene VDP Monomers. Within the limits mentioned above, it is frequentiy possible, and often desirable, to modify the /5-xylylene monomer by attaching to it certain substituents. Limitations on such modifications He ia three areas reactivity, performance ia the coater, and cost. 

Almost aU ceUophane is coated with either a moisture barrier or heat-sealable coating. This is generaUy done in tower coaters after film production. 

Technical Manual 1994, National Coil Coaters Association, Philadelphia, Pa. 

In 1933, the first roU coater was installed as an integral part of a paper machine. These on-machine coaters produce a low cost coated paper used largely for magazines. Coating of paper off-machine at speeds greater than paper machine manufacturing speeds is possible with the use of the various available blade coaters (17). 

At high speeds, the pond of the flooded nip size press becomes turbulent. RoU maintenance is a problem with the gate-roU size press. To avoid these problems, the blade/rod metering size press was developed. Short-dweU coater heads are used to apply a precisely controUed quantity of chemicals to the size press roUs. This quantity is controUed with either a metering blade or a metering rod. Blade or rod metering eliminates the pond, and does not increase the number of roUs required for surface chemical appHcation. 

Fig. 2. Vacuum processing chamber configuration (a) batch coater (b) load-lock coater (c) in-line coater (d) cluster tool (e) roU coater (batch) and (f) roU coater (air-to-air), [[ccsq]] represents the isolation valve with transfer tooling [[artl]], the motion of fixturing and [[art2]], the access door.

Poly(vinyl acetate) latex paints are the first choice for interior use (149). Their abihty to protect and decorate is reinforced by several advantages belonging exclusively to latex paints they do not contain solvents so that physiological harm and fire ha2ards are eliminated they are odorless they are easy to apply with spray gun, roUer-coater, or bmsh and they dry rapidly. The paint can be thinned with water, and bmshes or coaters can be cleaned with soap and tepid water. The paint is usually dry in 20 minutes to two hours, and two coats may be applied the same day. 

Chrome-complexed fluorochemicals, as weU as fluoropolymers, are widely used products. The compositions are proprietary. Fluorochemicals provide a high degree of water repeUency as weU as repeUency to aqueous stains, oUs, grease, and oilhorne stains. TraditionaUy, treatments are appUed duting a dmm process ia which about 30 min are required for flUl penetration of the leather to occur. Products are also avaUable for appUcation with sprayiag equipment and roU coaters. 

Because clays (rocks) usually contain more than one mineral and the various clay minerals differ in chemical and physical properties, the term clay may signify entirely different things to different clay users. Whereas the geologist views clay as a raw material for shale, the pedologist as a dynamic system to support plant life, and the ceramist as a body to be processed in preparation for vitrification, the chemist and technologist view clay as a catalyst, adsorbent, filler, coater, or source of aluminum or lithium compounds, etc. 

The primary substrates or support iaclude many types of paper and paperboard, polymer films such as polyethylene terephthalate, metal foils, woven and nonwoven fabrics, fibers, and metal cods. Although the coating process is better suited to continuous webs than to short iadividual sheets, it does work very well for intermittent coating, such as ia the printing process. In general, there is an ideal coater arrangement for any given product. 

In most coatiag operatioas a single layer is coated. Whea more than one layer must be appHed one can make multiple passes, or use tandem coaters where the next layer is appHed at another coatiag statioa ioimediately foUowiag the dryer sectioa for the previous layer, or a multilayer coatiag statioa can be used. Slot, extmsion, sHde, and curtain coaters are used to apply multiple layers simultaneously. SHde and curtain coaters can apply an unlimited number of layers simultaneously, whereas slot and extmsion coaters are limited by the complexity of the die internals. 

Fig. 2. (a) Puddle coater (b) roll appHcator blade coater (c) fountain blade coater. 

In the rod-blade coater unit a rod is mounted at the end of the blade. This coater behaves more like the beveled blade coater than a flexible blade... 

Two-BIa.de Coaters. In order to coat both sides of a web simultaneously, two flexible blade coaters can be used back-to-back, ie, with both blades pressing against each other and the web between them. The web usually travels vertically upward. Different coatings can be appHed on each side of the web. The blades tend to be thinner and more flexible than the standard blades and the angle to the web is lower. The web has to have sufficient tensile strength to be pulled through the nip. 

Kiss-Roll Colters. In kiss-roU coating, the web passes over a roU wet with the coating fluid, and has no backing roU. There are many types of kiss-roU coaters. The kiss roU can turn in the dkection of the web or in the reverse dkection but usually operates in the web dkection. Kiss-roU coaters are tension sensitive and are often used to apply excess coating prior to a metering device. 

---