Coal-water mixture, combustion

The coal-water mixture fed to the boilers has to be formulated to a certain specification. This is done with the proper inclusion of additives to facilitate combustion. The recommended additives include a petroleum-based surfactant (polysulfones or polycar-boxylates), a stabilizing (e.g. xanthan gum), a biocide and an anti-foaming agent (such as a silicone base). 

Morway (1965) obtained a patent for using a hydrocarbon oil with a small percentage of an imidazoline surfactant to coat coal particles uniformly. After adding this mixture, the coated coal can be mixed with water. The water weight concentration can be reduced to 20%. This slurry with low overall moisture is easier to heat at the final discharge point prior to combustion than plain coal-water mixtures. 

Typical coal water mixtures (CWMs) for direct combustion consist of a weight concentration of 70% coal and 30% water. Prior to combustion, it is important to degrade the coal slurry mixture by applying hot air to accelerate the evaporation of water (Garbett and Yiu. 1988). 

Derivation (1) Made almost pure by placing a mixture of oxygen and carbon dioxide in contact with incandescent graphite, coke, or anthracite. (2) Action of steam on hot coke or coal (water gas) or on natural gas (synthesis gas). In the latter case, carbon dioxide is removed by absorption in amine solution, and the hydrogen and carbon monoxide separated in a low-temperature unit. (3) By-product in chemical reactions. (4) Combustion of organic compound with limited amount of oxygen, as in automobile cylinders. (5) Dehydration of formic acid. 

These operations carry energy penalties, and the heat of combustion released when burning the methane, hydrogen, or carbon monoxide produced is less than the energy that would have been released had the coal been burned directly. To produce heavier liquids, the equimolar mixture of hydrogen and carbon monoxide (water gas, also known as synthesis... 

Gas, Combustible. Any gaseous substance or mixture consisting principally of carbon and hydrogen contg gases used for illuminating or heating purposes may be called combustible gas. These include blast furnace gas, carbon monoxide gas, coal gas, coke-oven gas, fuel gas, natural gas, oil gas, producer gas, tar gas, water gas and wood gas... 

A powder which burns with a green flame is obtained by the addition of nitrate of baryta to chlorate of potash, nitrate of potash, acetate of copper. A white flame is made by the addition of sulfide of antimony, sulfide of arsenic, camphor. Red by the mixture of lampblack, coal, bone ash, mineral oxide of iron, nitrate of strontia, pumice stone, mica, oxide of cobalt. Blue with ivory, bismuth, alum, zinc, copper sulfate purified of its sea water [sic]. Yellow by amber, carbonate of soda, sulfate of soda, cinnabar. It is necessary in order to make the colors come out well to animate the combustion by adding chlorate of potash.15... 

The lacking special description of the Gibbs phase rule in MEIS that should be met automatically in case of its validity is very important for solution of many problems on the analysis of multiphase, multicomponent systems. Indeed, without information (at least complete enough) on the process mechanism (for coal combustion, for example, it may consist of thousands of stages), it is impossible to specify the number of independent reactions and the number of phases. Prior to calculations it is difficult to evaluate, concentrations of what substances will turn out to be negligibly low, i.e., the dimensionality of the studied system. Besides, note that the MEIS application leads to departure from the Gibbs classical definition of the notion of a system component and its interpretation not as an individual substance, but only as part of this substance that is contained in any one phase. For example, if water in the reactive mixture is in gas and liquid phases, its corresponding phase contents represent different parameters of the considered system. Such an expansion of the space of variables in the problem solved facilitates its reduction to the CP problems. 

Environmental exposures are present through the human lifetime. However, they may vary considerably over time at the same location, for example, because of the local or global changes in emission and environmental pollution levels. Environmental exposures of humans consist of exposures outdoors and indoors as well as at workplaces these environments may significantly differ. The exposure media include air, water, and soil and dust. Historically, research on human exposures to chemicals and associated health effects has been conducted mostly on single chemicals. In addition, several studies have dealt with complex mixtures, such as diesel fuel and gasoline, by-products from coal combustion, and tobacco smoke. A common problem of complex mixtures is that the composition may vary from one exposure to another and, as a result, the associated toxicity may vary. For a better understanding... 

---