Capability, dissolving

Although the acetylation of alcohols and amines by acetic anhydride is almost invariably carried out under anhydrous conditions owing to the ready hydrolysis of the anhydride, it has been shown by Chattaway (1931) that phenols, when dissolved in aqueous sodium hydroxide solution and shaken with acetic anhydride, undergo rapid and almost quantitative acetylation if ice is present to keep the temperature low throughout the reaction. The success of this method is due primarily to the acidic nature of the phenols, which enables them to form soluble sodium derivatives, capable of reacting with the acetic... 

Since an enzyme is a biological catalyst and therefore merely accelerates a reaction, it cannot alter the position of equilibrium in a reversible reaction. The hydrolysis of p-methylglucoside is reversible and emulsin should therefore be capable also of synthesising this compound frc n glucose and methanol. This synthesis can actually be carried out by the action of the enzyme on glucose dissolved in an excess of methanol, the excess of the alcohol throwing the equilibrium over to the left. Owing to experimental difficulties, this reaction is not here described. 

The most desirable characteristics of a solvent for recrystalhsation are (a) a high solvent power for the substance to be purified at elevated temperatures and a comparatively low solvent power at the laboratory temperature or below (6) it should dissolve the impurities readily or to only a very small extent (c) it should yield well-formed crystals of the purified compound and (d) it must be capable of easy removal from the crystals of the purified compound, i.e., possess a relatively low boiling point. It is assumed, of course, that the solvent does not react chemically with the substance to be purified. If two or more solvents appear to be equally suitable for the recrystallisation, the final selection will depend upon such factors as ease of manipulation, inflammability and cost. 

It is only the contribution of AH to AG that we are discussing here, but we see the effect of this contribution-in the systems for which the approximation is valid-is that a solvent becomes less suitable to dissolve a polymer the greater the difference is between their 6 values. At best, when 61 = 62, the solvent effect is neutral. Cases for which a favorable specific interaction between solvent and polymer actually promotes solution are characterized by negative values of AH and are therefore beyond the capabilities of this model. 

Iron (qv) exists in three aHotropic modifications, each of which is stable over a certain range of temperatures. When pure iron free2es at 1538°C, the body-centered cubic (bcc) 5-modification forms, and is stable to 1394°C. Between 1394 and 912°C, the face-centered cubic (fee) y-modification exists. At 912°C, bcc a-iron forms and prevails at all lower temperatures. These various aHotropic forms of iron have different capacities for dissolving carbon. y-Iron can contain up to 2% carbon, whereas a-iron can contain a maximum of only about 0.02% C. This difference in solubHity of carbon in iron is responsible for the unique heat-treating capabilities of steel The soHd solutions of carbon and other elements in y-iron and a-iron are caHed austenite and ferrite, respectively. 

Reverse osmosis processes for desalination were first appHed to brackish water, which has a lower I DS concentration than seawater. Brackish water has less than 10,000 mg/L IDS seawater contains greater than 30,000 mg/L IDS. This difference in IDS translates into a substantial difference in osmotic pressure and thus the RO operating pressure required to achieve separation. The need to process feed streams containing larger amounts of dissolved soHds led to the development of RO membranes capable of operating at pressures approaching 10.3 MFa (1500 psi). Desalination plants around the world process both brackish water and seawater (15). 

Chemical Properties. The chemistry of the sulfur chlorides has been reviewed (141,142). Sulfur monochloride is stable at ambient temperature but undergoes exchange with dissolved sulfur at 100°C, indicating reversible dissociation. When distilled at its atmospheric boiling point, it undergoes some decomposition to the dichloride, but decomposition is avoided with distillation at ca 6.7 kPa (50 mm Hg). At above 300°C, substantial dissociation to S2 and CI2 occurs. Sulfur monochloride is noncombustible at ambient temperature, but at elevated temperatures it decomposes to chlorine and sulfur (137). The sulfur then is capable of burning to sulfur dioxide and a small proportion of sulfur trioxide. 

Solvent Extraction. With solvent extraction, organics are separated from a waste by mixing the waste with a solvent capable of dissolving or extracting the organics. The extraction process can have multiple stages and be operated where the solvent and waste pass concurrently or countercurrenfly. 

Separability. One of the greatest advantages of a solid catalyst is that it can be separated easily from the products of reaction. To do this successfully requires careful control of the process conditions so that exposure of the catalyst to nonreactant liquids capable of affecting or dissolving either the catalytic material or the support is prevented or rninimi2ed. Solid catalysts typically are used in axial or radial flow beds and multitubular reactors. Many successful commercial processes maintain the reactants and products in the gas phase while in contact with the catalyst to avoid catalyst degradation problems. 

The hquid vehicle in a slurry should have a low vapor pressure for Hquid extraction and drying be compatible with the soHds and casting mold be inexpensive and be capable of dissolving and dispersing deflocculants and other additives. Distilled or deionized water is generally used as the Hquid vehicle, however, organic Hquids must be used for such moisture sensitive oxide powders as CaO and MgO, and for oxidation sensitive nonoxide powders, eg, AIN. 

The physical properties of methylene chloride are Hsted in Table 1 and the binary a2eotropes in Table 2. Methylene chloride is a volatile Hquid. Although methylene chloride is only slightly soluble in water, it is completely miscible with other grades of chlorinated solvents, diethyl ether, and ethyl alcohol. It dissolves in most other common organic solvents. Methylene chloride is also an excellent solvent for many resins, waxes, and fats, and hence is well suited to a wide variety of industrial uses. Methylene chloride alone exhibits no dash or fire point. However, as Htde as 10 vol % acetone or methyl alcohol is capable of producing a dash point. 

One example is sampling for S02- Liquid sorbents for SO2 depend on the solubility of SO2 in the liquid collection medium. Certain liquids at the correct pH are capable of removing ambient concentrations of SO2 with 100% efficiency until the characteristics of the solution are altered so that no more SO2 may be dissolved in the volume of liquid provided. Under these circumstances, sampling is 100% efficient for a limited total mass of SO2 transferred to the solution, and the technique is acceptable as long as sampling does not continue beyond the time that the sampling solution is saturated (1). A second example is the use of solid sorbents such as Tenax... 

For example, nylon 66 will dissolve in formic acid, glacial acetic acid, phenol and cresol, four solvents which not only have similar solubility parameters but also are capable of acting as proton donors whilst the carbonyl groups on the nylon act as proton acceptors (Figure 5.6). 

Although moulded polycarbonate parts are substantially amorphous, crystallisation will develop in environments which enable the molecules to move into an ordered pattern. Thus a liquid that is capable of dissolving amorphous polymer may provide a solution from which polymer may precipitate out in a crystalline form because of the favourable free energy conditions. 

ACID A chemical compound whose aqueous solution turns blue litmus paper red, reacts with and dissolves certain metals to form salts, and reacts with bases to produce salts and water. They are capable of transfeiTing a hydrogen ion (proton) in solution. 

Both acids and alkalis are electrolytes. The latter when fused or dissolved in water conduct an electric current (see page 55). Acids are considered to embrace substances capable of accepting an electron pair. Mineral acids have wide usage as indicated by Table 3.4. 

---