Calcium carbonate density

Calcium carbonate can be prepared by the double decomposition of calcium chloride and sodium carbonate in aqueous solution. Its density and... 

Polypropylene polymers are typically modified with ethylene to obtain desirable properties for specific applications. Specifically, ethylene—propylene mbbers are introduced as a discrete phase in heterophasic copolymers to improve toughness and low temperature impact resistance (see Elastomers, ETHYLENE-PROPYLENE rubber). This is done by sequential polymerisation of homopolymer polypropylene and ethylene—propylene mbber in a multistage reactor process or by the extmsion compounding of ethylene—propylene mbber with a homopolymer. Addition of high density polyethylene, by polymerisation or compounding, is sometimes used to reduce stress whitening. In all cases, a superior balance of properties is obtained when the sise of the discrete mbber phase is approximately one micrometer. Examples of these polymers and their properties are shown in Table 2. Mineral fillers, such as talc or calcium carbonate, can be added to polypropylene to increase stiffness and high temperature properties, as shown in Table 3. 

Table 12. Effect of Calcium Carbonate Fillers on Oxygen Permeability of Low Density Polyethylene...

Filter aids should have low bulk density to minimize settling and aid good distribution on a filter-medium surface that may not be horizontal. They should also be porous and capable of forming a porous cake to minimize flow resistance, and they must be chemically inert to the filtrate. These characteristics are all found in the two most popular commercial filter aids diatomaceous silica (also called diatomite, or diatomaceous earth), which is an almost pure silica prepared from deposits of diatom skeletons and expanded perhte, particles of puffed lava that are principally aluminum alkali siheate. Cellulosic fibers (ground wood pulp) are sometimes used when siliceous materials cannot be used but are much more compressible. The use of other less effective aids (e.g., carbon and gypsum) may be justified in special cases. Sometimes a combination or carbon and diatomaceous silica permits adsorption in addition to filter-aid performance. Various other materials, such as salt, fine sand, starch, and precipitated calcium carbonate, are employed in specific industries where they represent either waste material or inexpensive alternatives to conventional filter aids. 

In the North American market, water heaters are almost always made with the cold water inlet and hot water outlet lines coming out of the top of the tank. The hot water outlet opens right into the top of the tank and so draws off the hottest water. The hot water has risen to the top of the tank because of its lower density. The cold water on the inlet side is directed to the bottom of the tank by a plastic dip-tube. In some models the dip-tube is curved or bent at the end to increase the turbulence at the bottom of the tank. This is to keep any sediment from settling on the bottom of the tank. As sediment— usually calcium carbonate or lime—precipitated out of the water by the increased temperature builds up, it will increase the thermal stress on the bottom of a gas-fired water heater and increase the likelihood of tank failure. On electric water heaters the sediment builds up on the surface of the elements, especially if the elements are high-density elements. Low-density elements spread the same amount of power over a larger surface of the element so the temperatures are not as high and lime doesn t build up as quickly. If the lower elements get completely buried in the sediment, the element will likely overheat and burn out. 

Density control with calcium carbonate, iron carbonate, barium carbonate, ferric oxide. 

Dual or triple media filters are used to provide a coarse to fine filtration facility. Where an anthracite-sand media bed is employed, the anthracite, which is half the density of sand, acts as a roughing filter prior to the finer sand bed. The larger and irregular voids within the anthracite bed are particularly suitable for the removal of floes, and filtration occurs deep within the bed. Where fine crystalline precipitates of calcium carbonate or calcium phosphate occur, smaller grain sizes may be employed without risk of high head loss or low filter rates. 

Calcium carbonate occurs in two forms— hexagonal crystal known as cal-cite, and orthorhombic form, aragonite. Calcite decomposes on heating at 825°C, aragonite melts at 1,339°C (at 102.5 atm). Density 2.71 g/cm (calcite), 2.83 g/cm3 (aragonite) insoluble in water (15mg/L at 25°C) Ksp 4.8x10 soluble in dilute mineral acids. 

Limestone is composed primarily of calcium carbonate. A 1.0-mm3 chip of limestone was accidentally dropped into a water-filled swimming pool, measuring 10m X 7m X 2 m. Assuming that the carbonate ion does not function as a Bronsted base and that the pH of the water is 7, will the pebble dissolve entirely The density of calcium carbonate is 2.71 g-cm 3. 

Insulation materials contain more air and have an lower apparent density than ordinary refractory materials. In the case of insulation bricks the desired porosity is obtained by making use of additives which produce gases when heated (e.g. calcium carbonate), or of porous raw materials. In figure 11.3. 2 the effect of the appplication of insulation bricks is represented. 

As mentioned earlier, pH changes occur from pollution stresses such as acid rain or mine runoff of from geochemical reactions such as dissolution of calcium carbonate. In acidified regions, species diversity and population density drop dramatically with some lakes and streams becoming devoid of life. Changes in metal complexes occur both naturally and biologically, with direct and indirect effects on ligand concentration and complex stability. 

This empirical relationship remains valid for light inorganic materials such as calcium carbonate, silica, aluminium, etc., and allows the density to be predicted with a maximum error of 10% in the range of most usual organic network densities (1100 < p < 1400 kg m 1). In this range, density can be approximated by a linear relationship ... 

Y. Bomal and P. Goddard, Melt Viscosity of Calcium-carbonate-filled Low Density Polyethylene Influence of Matrix-filler and Particle-particle Interactions, Polym. Eng. Sci., 36, 237-243 (1996). 

---