Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Butadiene rubber crosslink density

H and 2H NMR have been used in styrene-butadiene rubber (SBR) with and without carbon-black fillers to estimate the values of some network parameters, namely the average network chain length N. The values obtained from both approaches were checked to make sure that they were consistent with each other and with the results of other methods [71, 72, 73]. To this purpose, a series of samples with various filler contents and/or crosslink densities were swollen with deuterated benzene. The slopes P=A/ X2-X 1) obtained on deuterated benzene in uniaxially stretched samples were measured. The slopes increase significantly with the filler content, which suggests that filler particles act as effective junction points [72, 73]. [Pg.582]

Radiation vulcanization of carbon fiber reinforced styrene-butadiene rubber causes a substantial increase in crosslink density (Figure 11.4) and tensile strength (Figure 11.5). This magnitude of change is possible only when the interaction between the filler and the matrix is improved. When irradiated in the presence of air, carbon fibers gain functionality which substantially increases their adhesion resulting in a spectacular improvement in properties. SEM studies show that as the dose of radiation increases, the adhesion of the... [Pg.502]

Problem 2.37 A styrene-butadiene rubber with 23.5 mol% styrene in the polymer is vulcanized with sulfur, (a) Calculate the stress at 20% elongation of the vulcanizate in which 1.4% of the butadiene units are crosslinked. (b) What would be the corresponding stress if 2% of the butadiene units are crosslinked Assume random distribution of styrene and butadiene units in the polymer chain. [Density of vulcanizate (without filler) = 0.98 g/cm at 25°C.)... [Pg.97]

Sometimes the term reversion is applied to other types of nonoxidative degradation, especially with respect to rubbers not based on isoprene. For example, thermal aging of SBR (styrene-butadiene rubber), which can cause increased crosslink density and hardening, has been called reversion, since it can be the result of overcure and can also degrade a product s usefulness. [Pg.340]

Over the years, much of the research on accelerated-sulfur vulcanization was done by using natural rubber as a model substrate. Natural rubber was the first elastomer and therefore the search for the understanding of vulcanization originated with work on natural rubber. Most of the work cited in the previous sections is related to natural rubber. However, some rather early studies have been directed to the vulcanization of butadiene 1,4-polymers (Skinner and Watson, 1969 Wolfe et al, 1329 Gregg and Katrenick, 1970). More recent is the work of Pellicioli and coworkers. Early basic work on the vulcanization of ethylene-propylene-diene-monomer rubber (EPDM) has been carried out (van den Berg et al., 1984a,b). Recently, Kuno and coworkers did basic work on EPDM networks. They found that, essentially, the vulcanizate properties depend only on the crosslink density, not on the type of curing system (Dijkhuis et al., 2009). [Pg.363]

Wang et al. [60] utUized positron annihilation lifetime spectroscopy to measure the polymer free volume in mont-morillonite-styrene-butadiene rubber nanocomposites. There was an apparent reduction of the free volume of the polymer in the nanocomposite. The authors speculated that the reduction was primarily at the clay surface. This information is consistent with the crosslink density results reported above. [Pg.570]

Kalf et al. studied the effect of grafting cellulose acetate and methylmethacrylate as compatibilizers on acrylonitrile butadiene rubber (NBR) and styrene-butadiene rubber (SBR) blends. Morphology studies of the samples show an improvement in interfacial adhesion between the NBR and SBR phases in the presence of the prepared compatibilizing agents. The authors also reported the samples with grafted compatibilizers showed superior crosslink density and thermal stability, as compared to the blends without graft copolymers. ... [Pg.380]

SAXS can also be used to investigate the expected outcome of preparation processes of rubber-based materials. One example is the study of the evolution of the crosslink density of natural and styrene-butadiene rubbers, reported by Salgueiro et al.P who observed that changes in the vulcanization conditions bring about a shift and a widening of the SAXS signal. [Pg.534]

The barrier properties of 70/30 acrylonitrile-butadiene mbber/ethylene propylene diene monomer rubber (NBR/EPDM) vulcanizates, when loaded with carbon black fillers [e.g., I SAP (intermediate super-abrasion furnace), HAF (high-abrasion furnace) and SRF (semi-reinforcing furnace)] and using benzene, toluene and xylene as penetrants, have been examined with reference to the type of filler employed [66]. The filled samples were found to exhibit a better resistance to uptake of the three organic solvents when compared to the respective unfilled blends for any given blend ratio. With regards to the three types of carbon black used, solvent uptake was in the order SRF-> HAF-> ISAF-filled samples. The reason for this order was attributed to the better filler reinforcements and enhanced crosslink densities of the matrix as the size of the carbon black particles used was decreased. A similar behavior was also identified for NR/EVA composites [52]. [Pg.441]

The major degradation product of natural rubber is l-methyl-4-(l-methylethenyl)cyclo hexene. The presence of this compound as the major degradation product along with 2-methyl-1,3-butadiene (monomer) and groups of compounds containing 15 and 20 carbon atoms (three and four monomer units) in the pyrolysate of a rubber is sufficient to identify it as natural rubber. Similarly, the presence of l-chloro-4-(l-chloroethenyl)cyclohexene and 2-chloro-l, 3-butadiene, the cyclic dimer and monomer of poly(chloroprene) rubber, in the pyrolysate of a rubber identify it as poly(chloroprene) rubber. A correlation between the crosslink density and the product ratio of isoprene dimer species to isoprene formed from pyrolysis of natural rubber vulcanisates has been reported 697436 [a.232]. The major products of the isoprene dimer species were l,4-dimethyl-4-vinylcyclohexene and... [Pg.144]

The modified fillers were used in two matrices with different polarity the ethylene-propylene copolymer EPM and hydrogenated acrylonitrile-butadiene rubber HNBR. Elastomers were crosslinked with dicumyl peroxide DCP. The influence of the variously modified fillers on the cross-linking density of the vulcanizates, rheometric and mechanical properties of filled systems were investigated. The ageing studies (thermal, atmospheric and under UV radiations) were conducted. [Pg.73]


See other pages where Butadiene rubber crosslink density is mentioned: [Pg.570]    [Pg.385]    [Pg.429]    [Pg.364]    [Pg.192]    [Pg.280]    [Pg.693]    [Pg.43]    [Pg.569]    [Pg.720]    [Pg.18]    [Pg.136]    [Pg.96]    [Pg.221]    [Pg.264]    [Pg.514]    [Pg.143]    [Pg.171]    [Pg.21]    [Pg.424]    [Pg.138]    [Pg.384]    [Pg.159]    [Pg.107]    [Pg.172]    [Pg.155]    [Pg.71]   
See also in sourсe #XX -- [ Pg.335 , Pg.506 ]




SEARCH



Crosslink density

Crosslinked rubber

Crosslinking crosslink density

© 2024 chempedia.info