Boronic acids solutions

Compensation of reactivity margin Fuel elements with gadolinium oxide integrated in fuel pellets boron acid solution... 

Emergency protection All CPS control rods (48) are inserted into the core by gravity when their drives are deenergized by a protection system signal. System of emergency injection of boron acid solution... 

A solution of 6-bromoindole (O.lOmol) in toluene (200 ml) was treated with Pd(PPh3)4 (5mol%) and stirred for 30 min. A solution of 4-fluorophenyl-boronic acid (0.25 M, 0.15 mol) in abs. EtOH was added, followed immediately by sal aq. NaHCOj (10 eq.). The biphasic mixture was refluxed for several hours and then cooled to room temperature. The reaction mixture was poured into sat. aq. NaCl (200 ml) and the layers separated. The aq. layer was extracted with additional EtOAc (200 ml) and the combined organic layers dried (Na2S04), filtered and concentrated in vacuo. The solution was filtered through silica gel using hexane-CHjCl -hexanc for elution and evaporated. Final purification by recrystallization gave the product (19 g, 90%). 

Aqueous mineral acids react with BF to yield the hydrates of BF or the hydroxyfluoroboric acids, fluoroboric acid, or boric acid. Solution in aqueous alkali gives the soluble salts of the hydroxyfluoroboric acids, fluoroboric acids, or boric acid. Boron trifluoride, slightly soluble in many organic solvents including saturated hydrocarbons (qv), halogenated hydrocarbons, and aromatic compounds, easily polymerizes unsaturated compounds such as butylenes (qv), styrene (qv), or vinyl esters, as well as easily cleaved cycHc molecules such as tetrahydrofuran (see Furan derivatives). Other molecules containing electron-donating atoms such as O, S, N, P, etc, eg, alcohols, acids, amines, phosphines, and ethers, may dissolve BF to produce soluble adducts. 

The reactor coolant pH is controlled using lithium-7 hydroxide [72255-97-17, LiOH. Reactor coolant pH at 300°C, as a function of boric acid and lithium hydroxide concentrations, is shown in Figure 3 (4). A pure boric acid solution is only slightly more acidic than pure water, 5.6 at 300°C, because of the relatively low ionisation of boric acid at operating primary temperatures (see Boron COMPOUNDS). Thus the presence of lithium hydroxide, which has a much higher ionisation, increases the pH ca 1—2 units above that of pure water at operating temperatures. This leads to a reduction in corrosion rates of system materials (see Hydrogen-ION activity). 

Boric acid and fluoride ion react to form a series of fluroborates where OH is displaced by (see Fluorine compounds, inorganic—Boron, FLUOROBORic acid). Stepwise formation of the ions fluorotrihydroxyborate [32554-53-3] BF(OH) 3, difluorodihydroxyborate [32554-52-2] BF2(OH) 2 trifluorotrihydroxyborate [18953-00-9] BF3(OH) 3, proceeds rapidly in acidic solutions, but tetrafluoroborate [14874-70-5], forms slowly (56). A... 

The influence of boron-bonded ligands on the kinetics and mechanistic pathways of hydrolysis of amine boranes has been examined (37,38). The stoichiometry of trimetbyl amine azidoborane [61652-29-7] hydrolysis in acidic solution is given in equation 10. It is suggested that protonation occurs at the azide ligand enabling its departure as the relatively labile HN species. 

Fatty acids, n-hydroxy acids, ursoUc add Apply sample solution, followed by methanoUc boron trifluoride solution, heat with a hot-air drier, allow to cool and develop. [70]... 

Ethyl-2-methyl-3-(10,11) -dihydro-5H-dibenzo [a,d] cycloheptene-5-ylidene)-1 -pyrrolinium iodide (4.7 g) was dissolved in 7 cc of methanol. To this solution there were added 1.4 g of sodium boron hydride within about 80 minutes with stirring and stirring of the solution was continued for two hours to complete the reaction. The reaction mixture was acidified with 10% aqueous hydrochloric acid solution and then the methanol was distilled off. The residual solution was alkalized with 20% aqueous sodium hydroxide solution and extracted with ether. The ether layer was dried over magnesium sulfate and the ether was distilled off. The resulting residue was further distilled under reduced pressure to yield 2.0 g of 1-ethyl-2-methyl-3-(10,11 ) dihydro-5H-dibenzo[a,d]cycloheptene-5-ylidene)pyrrolidine (boiling point 167°C/4 mm Hg.). 

Calibration. Take 5, 10, 25, 50, 75 and lOOmL of the standard boric acid solution (2.5 x 10 4M) and make each up to lOOmL with distilled water this yields a boron concentration range up to 2.70mgL 1. Continue with each solution as described under procedure (b), i.e. one-hour reaction time, except that the initial neutralisation of the boron solution to pH 5.5 is not necessary. Construct a calibration graph of absorbance at 516 nm against boron concentration, mg L 1. For maximum accuracy, the calibration should be carried out immediately prior to the analysis of samples. 

Ignite the filter in a platinum crucible, fuse with 2.0 g of anhydrous sodium carbonate, dissolve the melt in 40 mL of dilute sulphuric acid, and add 1 mL of sulphurous acid solution (about 6 per cent) to reduce any iron(III) salt, etc., formed in the fusion, and filter if necessary. Transfer the solution to a 100 mL graduated flask, dilute to the mark, and mix. This flask (B) contains the acid-insoluble boron. 

In acid solution 1-acyl-1//-azepines and alkyl l//-azepine-l-carboxylates undergo rapid aromatization to A-arylcarbamates,115,139,142 whereas 1/Z-azepine-l-carbonitrile suffers quantitative rearrangement and hydrolysis to phenylurea.163 Rearrangement of ethyl l//-azepine-l-carboxylate to ethyl A-phenylcarbamate is also rapid (5 min) and quantitative with boron trifluoride-diethyl ether complex in benzene.245... 

The dehydrogenation of 2,3-dihydro- and 2,5-dihydro-l//-l-benzazepines to 3//-l-benz-azepincs with heterocyclic enamines in the presence of boron trifluoride diethyl ether complex has been achieved in moderate yields (30-35%).241 In contrast, electrochemical oxidation of 2,5-dihydro-1 H- -benzazepines in buffered acetic acid solution furnishes initially 5//-l-benz-azepines in 35-45% yield.242... 

Yagi I, Ishida T, et al. 2004. Electrocatal)tic reduction of oxygen to water at Au nanoclusters vacuum-evaporated on boron-doped diamond in acidic solution. Electrochem Commun 6 773-779. 

Shinkai (65) exploited the boronic acid-diol motif mentioned above to self-assemble a polymer based on pyridine-magnesium porphyrin interactions. In this case, the evidence for polymerization comes from lightscattering experiments in dilute solution which yielded an average molecular weight of 109 g mol-1 for this system. 

A group of peptide derivatives such as peptide arginals and boronic acid peptide derivatives belong to another class of reversible thrombin inhibitors. One such inhibitor is PPACK (D-Phe-Pro-Arg chloromethyl ketone), which functions as a powerful irreversible thrombin inhibitor by alkylating the histidine residue at the catalytic site of thrombin (58). It, however, is unstable in neutral solution, as it undergoes cyclization and inactivation. However, the D-methyl derivative of D-Phe-Pro-Arg-H (D-Mephe-Pro-Arg-H) called efegatran, with a molecular mass of 515 Da, is a stable selective reversible inhibitor of thrombin with a K. of approximately 100 nM. The basic amino terminus in this compound is responsible for promoting the specificity toward thrombin (63). 

The proposed mechanism of the boron-catalyzed amidation is depicted in the Figure. It has been ascertained by H NMR analysis that monoacyloxyboronic add 1 is produced by heating the 2 1 mixture of 4-phenylbutyric add and [3,5-bis(trifluoromethyl)phenyl]boronic acid in toluene under reflux with removal of water. The corresponding diacyloxyboron derivative is not observed at all. When 1 equiv of benzylamine is added to a solution of 1 in toluene, the amidation proceeds even at room temperature, but the reaction stops before 50% conversion because of hydrolysis of 1. These experimental results suggest that the rate-determining step is the generation of 1. 

Lee J, Fujishima A, Honda K, Kumashiro Y (1985) Photoelectrochemicl behaviour of p-type boron phosphide photoelectrode in acidic solution. Bull Chem Soc Jpn 58 2634-2637... 

Toxicosis in animals has resulted from ingestion of boric acid or borax solutions, from topical applications of boric acid solutions to damaged skin, and from inhalation of boranes the exact mechanisms of action are not understood. Boron and its compounds are potent teratogens when applied directly to the embryo, bnt there is no evidence of mutagenicity or carcinogenicity. Boron s unique affinity for cancerons tissnes has been exploited in neutron capture radiation therapy of malignant hnman brain tnmors. 

A flask was charged with 4-bromo-iodobenzene (0.079 mol), 4-methoxy-2-methyl-phenyl boronic acid (0.087 mol), palladium acetate (0.004 mol), and triphenyl phosphine (0.008 mol) and then treated with 200 ml acetone and 250 ml 2M NaHCO i. The mixture was refluxed at 65°C for 18 hours and was then treated with water and diethyl ether and the organic layer isolated. This layer was washed with 40 ml saturated sodium chloride solution and water, dried over MgSC>4, filtered, and concentrated. The residue was purified by column chromatography using silica gel with CH2C12/ hexane, 1 1, and then recrystallized in / , 7 3, respectively, and 16.4 g of product isolated. 

A reactor containing 10 ml of toluene and 10 ml of aqueous Na2C03 was treated with the step 2 product (1.0 mmol), 2,7-dipinacol boron-9,9-di-octyl-fluoiene (1.0 mmol), tetrakis triphenylphosphine palladium (0.01 mmol), and 0.16 ml of tricaprylmethyl-ammonium chloride. The mixture was then treated with a few drops of bromobenzene and then refluxed for 1 hour and treated with a few drop of phenyl boronic acid and then further refluxed 15 hours and cooled. The mixture was diluted with toluene and isolated toluene layer washed with water. The mixture was filtered after adding 40 mg of the palladium scavenger 3-mercaptopropyl modified silica gel. The solution was then poured into methanol and a yellow polymer isolated. The polymer was redissolved in toluene and then purified using a short column of silica gel. The solution was rewashed with water, reprecipitated in ethanol, and 0.80 g of polymer isolated having an Mn of 32,800 Da. 

---