Binder oven

SILIKOFTAL ED binder, optical fiber coatings Actllane 230HD30 binder, org. solvent systems Ethyl hydroxyethyl ceUilose binder, outdoor paints Potassium silicate binder, oven anticorrosive paints SILIKOPHEN P 60/D SiLiKOPHEN P 65/W SiLiKOPHEN P 70/MPA SILIKOPHEN P 80/20 SILIKOPHEN ... 

SILIKOPHEN P40/W binder, oven insert anticorrosive paints... 

Post-deposition annealing of Au-covered PTFE was carried out in air at 300°C ( 3°C) for 1 h using a thermostat Binder oven. The heating rate was 5°C/min and the annealed samples were left to cool in air to room temperature (RT) [42]. 

Nonstabilized foams are referred to as froths froth-bonded fabrics are similar in properties to some saturation-bonded nonwovens. Typical foams used as nonwoven binder solutions have a consistency similar to shaving cream. AppHcation methods include knife-edge layering onto a horizontal web surface followed by vacuum penetration, and saturation and penetration of a vertical web surface using a horizontal-nip pad. Drying and curing is carried out in ovens, dmm dryers, or steam cans. 

Foundry Resins. In the foundry industry, phenoHc resins are used as the binder for sand in the manufacture of sheU molds and cores. The two mating halves are joined by clamps or a bonding agent to form a sheU mold into which the molten metal is poured for castings. The sheU is formed by depositing a resin—sand mix on a hot metal pattern plate. After a certain period the pattern is inverted and the excess resin sand is removed. The sand particles are bonded by an oven cure, and the sheU is ejected from the pattern plate. 

Pitch. The principal outlet for coal-tar pitch is as the binder for the electrodes used in aluminum smelting. These are of two types. Older plants employ Sn derberg furnaces, which incorporate paste electrodes consisting of a mixture of about 70% graded petroleum coke or pitch coke and 30% of a medium-hard coke-oven pitch. This paste is added periodically to the top of the monolithic electrode as it is consumed. The more modem smelters employ prebaked electrodes requiring less binder, about 18%. 

The demand for electrode binder pitch has grown as aluminium output has expanded and the requirement for aluminium smelting is now between 1.5 and 2 x 10 t /yr. In Japan pitch is used for mixing with coal for carbonization in coke ovens to make metallurgical coke. 

The principal binder material, coal-tar pitch, is produced by the distillation of coal tar. Coal tar is obtained primarily as a by-product of the destmctive distillation of bituminous coal in coke ovens during the production of metallurgical coke. Petroleum pitch is used to a much lesser extent as a binder in carbon and graphite manufacture. Because of its low sohds content, petroleum pitch is used as an impregnant to strengthen carbon artifacts prior to graphitization. 

Coke-making ovens Organic acids, aldehydes, smoke. Use of binders that will allow ovens... 

The wool passes through an oven, which cures the resinous binder and determines the thickness of the product. On leaving the oven, the insulation is trimmed, slit and chopped into the appropriate product length prior to reaching the packing station, where it is either packaged as rolls or slabs. 

The anodes of these two graphite samples were fabricated from a slurried mixture which contains 92 wt% of active graphite powder and 8wt% polyvinylidene difluoride (PVDF) polymer binder (Kureha 9130) and using 1 -methyl-2-pyrrolidinone (NMP) (Aldrich, >99%) as the solvent. After getting the homogenous slurry, the electrode laminates were coated on Cu current collector foil using a doctor blade in the laboratory-made laminate-coater. The laminates were then dried first at 75°C in air for 3 hrs and then the final heat treatment was carried out in a vacuum oven at 75 C for 10 hrs. Finally, the laminates were calendared to about 35% porosity in a dry room. 

Conditions to be met in oven drying enamels depend also on the composition of the binder. Paint systems containing melamine-formaldehyde or urea-formaldehyde resins, for instance, harden by polycondensation with other resins, such as epoxy resins, short-oil alkyd or acrylic resins at elevated temperatures. Baking is carried out at temperatures between 100 and almost 200°C and may last from a few minutes to more than an horn. A general trend towards energy conservation has shifted public attention towards binders which require low baking temperatures. 

Sources/Uses. Occur as emissions from coke ovens, from coking of coal tar pitch, and ftom Soderberg aluminum reduction electrolytic cells used for base coatings and paints for roofing and paving and as a binder for carbon electrodes... 

In cold molding, the compound is compacted in a mold at around room temperature. The compressing operation is similar to that employed in the production of KBr pellets from powdered KBr. The compound generally contains a lot of filler and binder. The compacted material is removed from the mold and placed in an oven where it becomes cross-linked. Ceramic materials are often produced using cold molding. 

Screen printing of UV inks is being done over paper, metal, films, foils, plastics, and PVC. Radiation curable materials are being used as vehicles for ceramic inks that are screened onto automotive windshields, cured, and then fired in an oven to bum off the organic binder and fuse the ceramic into the glass windshield. ... 

This technology (16, 17) produces sulphur concrete blocks by a manufacturing process very different from a hot poured sulphur concrete system. Solid sulphur, aggregate, liquid and a mineral binder are mixed together cold and compacted into a mold. Because of the presence of the small amount of liquid and mineral binder, the product retains its shape, although at this point the sulphur is not binding the product together in any way. The block is then dried to remove the liquid and heated in an oven to melt the sulphur. 

Comparison of Binder Properties After Thin-Film Oven Test (AASHTO T-179)... 

The final operation in propellant manufacture is the curing of the binder. The shaped material is placed in a curing oven for 16-48 hr at 80-110°C. The temperature and duration of this operation depend on the composition of the mixture, the dimensions of the charge and the physical properties desired. 

---