Cold baths

Simple cooling utilizes a cold-water bath. Cold-water baths are used to keep the reaction temperature from 15 to 50 Celsius. In some cases the water bath will have to be quickly drained, and then refilled with cold water in order to maintain the desired reaction temperature. In most cases cold-water baths are used for general long-term temperature control. 

The thermocouples were made from copper and constantan wire 0.0127 cm. in diameter. The junction was soldered with silver and the thermocouple was either peened into or spot welded to the calorimeter roughly at its center. The leads of the thermocouple were led out through a small hole in the end plate of the cell. Identical temperature rises were obtained with and without an ice-bath cold-junction and in general the wires were joined directly to the recorder inputs. 

Place 0 5 ml. of acetone, 20 ml. of 10% aqueous potassium iodide solution and 8 ml. of 10% aqueous sodium hydroxide solution in a 50 ml. conical flask, and then add 20 ml. of a freshly prepared molar solution of sodium hypochlorite. Well mix the contents of the flask, when the yellow iodoform will begin to separate almost immediately allow the mixture to stand at room temperature for 10 minutes, and then filter at the pump, wash with cold w ater, and drain thoroughly. Yield of Crude material, 1 4 g. Recrystallise the crude iodoform from methylated spirit. For this purpose, place the crude material in a 50 ml. round-bottomed flask fitted with a reflux water-condenser, add a small quantity of methylated spirit, and heat to boiling on a water-bath then add more methylated spirit cautiously down the condenser until all the iodoform has dissolved. Filter the hot solution through a fluted filter-paper directly into a small beaker or conical flask, and then cool in ice-water. The iodoform rapidly crystallises. Filter at the pump, drain thoroughly and dry. 

After about 20 minutes, when the liquid should be dry, filter it through a small fluted filter-paper into a 100 ml. distilling-flask attached to a water-condenser. Add some fragments of unglazed porcelain to the ethyl acetate, fit a 100° thermometer to the flask, and place the latter on a cold water-bath, which is then brought to the boil. Some ether is always formed as a by-product with the ethyl acetate, and by these means is carefully distilled off as a... 

Add in turn benzyl chloride (8 3 g., 8 o ml.) and powdered thiourea (5 gm.) to 10 ml. of 95% ethanol in a 100 ml. flask fitted with a reflux condenser. Warm the mixture on the water-bath with gentle shaking until the reaction occurs and the effervescence subsides then boil the mixture under reflux for 30 minutes. Cool the clear solution in ice-water, filter off the crystalline deposit of the benzylthiouronium chloride at the pump, wash it with ice-cold ethyl acetate, and dry in a desiccator. Yield, 11-12 g., m.p. 170-174°. The white product is sufficiently pure for use as a reagent. It is very soluble in cold water and ethanol, but can be recrystallised by adding ethanol dropwise to a boiling suspension in ethyl acetate or acetone until a clear solution is just obtained, and then rapidly cooling. 

Carry out this preparation precisely as described for the a-compound, but instead of zinc chloride add 2 5 g. of anhydrous powdered sodium acetate (preparation, p. 116) to the acetic anhydride. When this mixture has been heated on the water-bath for 5 minutes, and the greater part of the acetate has dissolved, add the 5 g. of powdered glucose. After heating for I hour, pour into cold water as before. The viscous oil crystallises more readily than that obtained in the preparation of the a-compound. Filter the solid material at the pump, breaking up any lumps as before, wash thoroughly with water and drain. (Yield of crude product, io o-io 5 g.). Recrystallise from rectified spirit until the pure -pentacetylglucose is obtained as colourless crystals, m.p- 130-131° again two recrystallisations are usually sufficient for this purpose. 

Boil the mixture gently on a sand-bath for 4 hours and then decant into a conical flask and cool. Seed the cold solution if necessary with a trace of a-methylglucoside. The glucoside separates as colourless crystals. When crystallisation ceases, filter the glucoside at the pump, drain, wash quickly with a small quantity of methanol, and then recrystallise from a minimum of methanol. For this purpose methanol of good quality, but not necessarily anhydrous, should be used. The a-methylglucoside is obtained as colourless crystals, m,p. 165°. Yield, 6-7 g. 

Place 0 5 ml. of the pyridine in a 200 ml. round- or flat-bottomed flask and add 34 ml. (30 g.) of benzene. Fit the flask with a reflux water-condenser, and then place it in a cold water-bath. If the experiment is conducted in a fume-cupboard, the top of the condenser can be closed with a calcium chloride tube bent downwards (as in Fig. 61, p. 105 or in Fig. 23(A), p. 45, where the outlet-tube A will carry the calcium chloride tube) and the hydrogen bromide subsequently allowed to escape if, however, the experiment is performed in the open laboratory, fit to the top of the condenser (or to the outlet-tube A) a glass delivery-tube which leads through a piece of rubber tubing to an inverted glass funnel, the rim of which dips just below the surface of some water... 

Add 23 g. of powdered (or flake ) sodium hydroxide to a solution of 15 ml. (18 g.) of nitrobenzene in 120 ml. of methanol contained in a 250 ml. short-necked bolt-head flask. Fix a reflux water-condenser to the flask and boil the solution on a water-bath for 3 hours, shaking the product vigorously at intervals to ensure thorough mixing. Then fit a bent delivery-tube to the flask, and reverse the condenser for distillation, as in Fig. 59, p. 100, or Fig. 23(D), p. 45). Place the flask in the boiling water-bath (since methanol will not readily distil when heated on a water-bath) and distil off as much methanol as possible. Then pour the residual product with stirring into about 250 ml. of cold water wash out the flask with water, and then acidify the mixture with hydrochloric acid. The crude azoxybenzene separates as a heavy oil, which when thoroughly stirred soon solidifies, particularly if the mixture is cooled in ice-water. 

Mix 6 2 ml. (6 4 g.) of pure ethyl acetoacetate and 5 ml. of pure phenylhydrazine in an evaporating-basin of about 75 ml. capacity, add 0 5 ml. of acetic acid and then heat the mixture on a briskly boiling water-bath (preferably in a fume-cupboard) for I hour, occasionally stirring the mixture with a short glass rod. Then allow the heavy yellow syrup to cool somewhat, add 30-40 ml. of ether, and stir the mixture vigorously the syrup may now dissolve and the solution shortly afterwards deposit the crystalline pyrazolone, or at lower temperatures the syrup may solidify directly. Note. If the laboratory has been inoculated by previous preparations, the syrup may solidify whilst still on the water-bath in this case the solid product when cold must be chipped out of the basin, and ground in a mortar with the ether.) Now filter the product at the pump, and wash the solid material thoroughly with ether. Recrystallise the product from a small quantity of a mixture of equal volumes of water and ethanol. The methyl-phenyl-pyrazolone is obtained... 

Whilst the solution is still hot, add dilute hydrochloric acid until the stirred solution is just acid to litmus, and then distil off as much ethanol as possible, using the water-bath. Now add more dilute hydrochloric acid to the residual hot solution until it is just acid to methyl-orange. The 5,5-dimethyl-cyclohexan-1,3-dione separates as an oil which solidifies on cooling. Filter the product at the pump, wash it with ice-cold water, and dry it in a desiccator. Yield of the pale cream-coloured crystals, 12 g. m.p. 136-145 (preliminary softening). 

Dissolve 13 g. of sodium in 30 ml. of absolute ethanol in a 250 ml. flask carrying a reflux condenser, then add 10 g. (9 5 ml.) of redistilled ethyl malonate, and place the flask on a boiling water-bath. Without delay, add a solution of 5 3 g. of thiourea in a minimum of boiling absolute ethanol (about 100 ml.). The sodium salt of thiobarbituric acid rapidly begins to separate. Fit the water-condenser with a calcium chloride guard-tube (Fig. 61, p. 105), and boil the mixture on the water-bath for 1 hour. Cool the mixture, filter off the sodium salt at the pump and wash it with a small quantity of cold acetone. Dissolve the salt in warm water and liberate the acid by the addition of 30 ml. of concentrated hydrochloric acid diluted with 30 ml. of water. Cool the mixture, filter off the thiobarbituric acid, and recrystallise it from hot water. Colourless crystals, m.p. 245 with decomposition (immersed at 230°). Yield, 3 5 -4 0 g. 

---