Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Bag moldings

Bag molding Hinterspritzen This patented process allows virgin or recycled TPs such as PP, PC/ABS, etc. to thermally bond with the backing of multilayer PP based fabrics providing good elasticity. This one step molding technique provides a low cost approach for in-mold fabric lamination that range from simple to complex shapes. [Pg.512]

Lost-wax Also called RP molding, fusible-core. A bar (or any shape) of wax is wrapped with RP. After the RP is cured (bag molding, etc.) in a simplified restrictor mold to keep the RP-wax shape, the wax is removed by drilling a hole or removing the end caps by applying a low temperature so that the RP is not effected (review in this chapter INJECTION MOLDING, Modified... [Pg.517]

Pressure bag molding This is a take-of to vacuum bag molding where the bag and mold is placed in a closed system and is subjected to pressure during the curing cycle. [Pg.517]

Compression molding Filament winding Hand lay-up Mat molding Pressure bag molding Continuous pultrusion Injection molding Spray-up... [Pg.557]

Because closer tolerances were reqd the case walls were much smaller than those produced previously, the conventional female bag molding technique could not be applied to the fabrication of felt body cases. It became necessary to design new molds and to modify the fabrication technique... [Pg.205]

Vacuum-Bag Molding. After hand lay-up, the assembly is covered with an air-tight film, typically polyvinyl alcohol, occasionally nylon or other material. Then a vacuum is pulled on the underside of the film, to let atmospheric pressure squeeze out air and excess resin. Use of a hand-held paddle may help. The assembly is allowed to stand until cured. Products are void-free, and quality is better than simple hand lay-up. [Pg.685]

Pressure-Bag Molding. This is similar to vacuum-bag molding, but 345 kPa (50 psi) air... [Pg.685]

Autoclave Molding. This is similar to pressure-bag molding, but it is carried out in an autoclave to apply the pressure to the outside of the cover film. [Pg.686]

Compression Molding Flexible Plunger Flexible Bag Molding Laminate Hand Lay-Up Vacuum Bag Molding Vacuum Bag Molding and Pressure Pressure Bag Molding Autoclave Molding Autoclave Press Clave Wet Lay-Up... [Pg.457]

Bag Molding Hinterspritzen Contact Molding Filament Winding Fabricating RP Tank... [Pg.457]


See other pages where Bag moldings is mentioned: [Pg.86]    [Pg.810]    [Pg.517]    [Pg.1026]    [Pg.208]    [Pg.440]    [Pg.445]    [Pg.445]    [Pg.473]    [Pg.503]    [Pg.512]    [Pg.517]    [Pg.523]    [Pg.636]    [Pg.672]    [Pg.672]    [Pg.692]    [Pg.701]    [Pg.84]    [Pg.155]    [Pg.95]    [Pg.95]    [Pg.86]    [Pg.810]    [Pg.1689]    [Pg.88]    [Pg.222]    [Pg.133]    [Pg.135]    [Pg.136]    [Pg.136]    [Pg.136]    [Pg.216]    [Pg.459]    [Pg.478]   
See also in sourсe #XX -- [ Pg.588 ]

See also in sourсe #XX -- [ Pg.272 ]

See also in sourсe #XX -- [ Pg.327 ]

See also in sourсe #XX -- [ Pg.50 ]




SEARCH



Bag Molding Hinterspritzen

Bag Molding and Pressures

Bagging

Flexible bag moldings

Pressure bag molding

Reinforced-plastic bag molding

Reinforced-plastic pressure bag molding

Reinforced-plastic vacuum-bag molding

Vacuum bag molding

© 2024 chempedia.info