ASTM scale

The other scale is the American Society for Testing and Materials (ASTM) scale. Unlike the Gulfjjort scale, which measures wood damage, the ASTM scale is a wood soundness scale measuring loss of cross-sectional area and has... 

When referring to data published by Dartmouth University, we have performed this conversion so that all values in this chapter appear in the ASTM scale. 

As a consequence, other than its use in the ndM method, the refractive index is very often used in process operations because it can indicate smaii differences in product quality that would be missed by other measurements. The only restriction is that the color of the sample should be less than 5 on the ASTM D 1500 scale. 

ASTM proposes representing the kinematic viscosity of hydrocarbons by a straight line on graph paper, called viscometric, for which the scales are such that ... 

The tendency of the color to become darker with time is often indicative of chemical degradation. The test is conducted with the aid of a colorimeter (NF T 60-104 and ASTM D 1500) and by comparison with colored glass standards. The scale varies from 0.5 to 8. The French specifications stipulate that diesel fuel color should be less than 5, which corresponds to an orange-brown tint. Generally, commercial products are light yellow with indices from 1 to 2. 

One problem associated with discussing flame retardants is the lack of a clear, uniform definition of flammabiHty. Hence, no clear, uniform definition of decreased flammabiHty exists. The latest American Society for Testing and Materials (ASTM) compilation of fire tests Hsts over one hundred methods for assessing the flammabiHty of materials (2). These range in severity from small-scale measures of the ignitabiHty of a material to actual testing in a full-scale fire. Several of the most common tests used on plastics are summarized in Table 1. 

Fracture mechanics is now quite weU estabHshed for metals, and a number of ASTM standards have been defined (4—6). For other materials, standardization efforts are underway (7,8). The techniques and procedures are being adapted from the metals Hterature. The concepts are appHcable to any material, provided the stmcture of the material can be treated as a continuum relative to the size-scale of the primary crack. There are many textbooks on the subject covering the appHcation of fracture mechanics to metals, polymers, and composites (9—15) (see Composite materials). 

This table shows the relationship between hardness testing scales, but should not be used for hardness converson. See ASTM E140 (2) for specific materials conversions. 

Conversion to other hardness scales from Vickers is approximated for specific materials Hsted in ASTM E140 (2). Conversions outside the stated areas should be avoided unless supported by test data. 

Scleroscope hardness numbers are convertible to other hardness scales (see ASTM E140) (2). 

Barcol Indenter. The Barcol hardness tester is a hand-held, spring-loaded instmment with a steel indenter developed for use on hard plastics and soft metals (ASTM D2583) (2). In use the indenter is forced into the sample surface and a hardness number is read direcdy off the integral dial indicator caUbrated on a 0 to 100 scale. Barcol hardness numbers do not relate to nor can they be converted to other hardness scales. The Barcol instmment is caUbrated at each use by indenting an aluminum ahoy standard disk suppHed with it. The Barcol test is relatively insensitive to surface condition but may be affected by test sample size and thickness. 

International Rubber Hardness. The International mbber hardness test (ASTM D1415) (2) for elastomers is similar to the Rockwell test ia that the measured property is the difference ia penetration of a standard steel ball between minor and major loads. The viscoelastic properties of elastomers require that a load appHcation time, usually 30 seconds, be a part of the test procedure. The hardness number is read directly on a scale of 0 to 100 upon return to the minor load. International mbber hardness numbers are often considered equivalent to Durometer hardness numbers but differences ia iadenters, loads, and test time preclude such a relationship. 

Color. Colors of hydrocarbon resins are routinely deterrnined on the Gardner scale (ASTM D154) or on the Saybolt scale (ASTM D156). 

Flame Resistance. Traditionally, small-scale laboratory flammabiUty tests have been used to initially characterize foams (38). However, these do not reflect the performance of such materials in bulk form. Fire characteristics of thermal insulations for building appHcations are generally reported in the form of quaHtative or semiquantitative results from ASTM E84 or similar tunnel tests (39). Similar larger scale tests are used for aircraft and marine appHcations. 

Eigelstein, H. C., and E. N. Skinner. The Effect of Composition on the Scaling of Iron-Chromium-Nickel Alloys Subjected to Cyclic Temperature Conditions, ASTM, STP No. 165 (1954). 

IPS), nominal inside diameter. One example of dimensional comparison for IPS pipe for Schedules 5 and 10 are compared to one standard scale of tubing in Table 2-1. The tubing conforms to ANSI/ASTM A-403-78 Class CR (stainless) or MSS Manufacturers Standard Society SP-43, Sch 5S. 

Mass-gain determinations are most common in studies of the extent and rate of oxidation or scaling at elevated temperatures (see ASTM G54 1984). 

Evaluation of loop-test results Although the thermal loop test approximates to the conditions which obtain in a dynamic heat-transfer system, in evaluating the results it is necessary to be aware of those aspects in which the test differs from the full-scale unit, as otherwise unwarranted confidence may be placed in the data. Assuming that adequate attention has been paid to the purity and condition of components, etc., the following factors will, according to ASTM G68 1980, influence the observed corrosion behaviour ... 

It is the general consensus within the worldwide fire community that the only proper way to evaluate the fire safety of products is to conduct full-scale tests or complete fire-risk assessments. Most of these tests were extracted from procedures developed by the American Society for Testing and Materials (ASTM) and the International Electrotechnical Commission (IEC). Because they are time tested, they are generally accepted methods to evaluate a given property. Where there were no universally accepted methods the UL developed its own. 

Tests for indention under load are performed basically like the ASTM measure the hardness of other materials, such as metals and ceramics. There are at least four popular hardness scales in use. Shore A and Shore D is for soft to relatively hard plastics and elastomers. Barcol is used from the mid-range of Shore D to above it as well as RPs. Rockwell M is used for very hard plastics (Chapter 5, MECHANICAL PROPERTY, Hardness),... 

Not darker than color standard No 5 of ASTM platinum-cobalt scale Not more than 1° and shall... 

---