Anhydrides, acid esterification

In general, the reactions of the perfluoro acids are similar to those of the hydrocarbon acids. Salts are formed with the ease expected of strong acids. The metal salts are all water soluble and much more soluble in organic solvents than the salts of the corresponding hydrocarbon acids. Esterification takes place readily with primary and secondary alcohols. Acid anhydrides can be prepared by distillation of the acids from phosphoms pentoxide. The amides are readily prepared by the ammonolysis of the acid haUdes, anhydrides, or esters and can be dehydrated to the corresponding nitriles (31). 

Esters are most commonly prepared by the reaction of a carboxyHc acid and an alcohol with the elimination of water. Esters are also formed by a number of other reactions utilizing acid anhydrides, acid chlorides, amides, nitriles, unsaturated hydrocarbons, ethers, aldehydes, ketones, alcohols, and esters (via ester interchange). Detailed reviews of esterification are given in References 1—9. 

In a typical process for manufacture on a commercial scale bleached wood pulp or cotton linters are pretreated for 12 hours with 40-50% sulphuric acid and then, after drying, with acetic acid. Esterification of the treated cellulose is then carried out using a mixture of butyric acid and acetic anhydride, with a trace of sulphuric acid as catalyst. Commercial products vary extensively in the acetate/ butyrate ratios employed. 

Esterification of linalool requires special reaction conditions since it tends to undergo dehydration and cyclization because it is an unsaturated tertiary alcohol. These reactions can be avoided as follows esterification with ketene in the presence of an acidic esterification catalyst below 30 °C results in formation of linalyl acetate without any byproducts [71]. Esterification can be achieved in good yield, with boiling acetic anhydride, whereby the acetic acid is distilled off as it is formed a large excess of acetic anhydride must be maintained by continuous addition of anhydride to the still vessel [34]. Highly pure linalyl acetate can be obtained by transesterification of tert-butyl acetate with linalool in the presence of sodium methylate and by continuous removal of the tert-butanol formed in the process [72]. 

Dehydrolinalool, obtained by ethynylation of 6-methyl-5-hepten-2-one, can be converted into dehydrolinalyl acetate with acetic anhydride in the presence of an acidic esterification catalyst. Partial hydrogenation of the triple bond to linalyl acetate can be carried out with, for example, palladium catalysts deactivated with lead [73]. 

Cobalt catalysts completely dominated industrial hydroformylation rmtil the early 1970s, when rhodium catalysts were commercialized. Most aldehydes produced are hydrogenated to alcohols or oxidized to carboxylic acids. Esterification of the alcohols with phthalic anhydride produces dialkyl phtha-late plasticizers that are primarily used for polyvinyl chloride plastics - the largest single end-use. Detergents and surfactants make up the next largest category, followed by solvents, lubricants, and chemical intermediates. 

The key to the formation of acyl derivatives involves removing the influence of the oxygen lone pairs on the electron-deficient carbon atom of the carbonyl group. This may be achieved either by protonation or by the formation of a mixed anhydride. Thus esterification occurs with an alcohol and an acid catalyst (Scheme 3.56). Protonation of the carbonyl... 

A new acidic esterification has been reported in which a carboxylic silyl ester is condensed with an alcohol under the action of p-trifluoromethylbenzoic anhydride and a combination of HfCU and AgOTf as catalyst (Eq. 15). The esters are obtained in high yields even if almost equimolar amounts of substrates are employed. The method is applicable to the esterification of a,j8-enoic acids, such as crotonic acid, which is often hampered by side reactions, e.g. E Z isomerization, deconjugation, and the Michael reaction [21a,b]. 

This method, although requiring longer reaction times than the symmetrical method, results in products virtually free of impurities arising horn enantio-merization and dipeptide formation (6). It involves formation of a mixed anhydride between an Fmoc-amino acid derivative and 2,6-dichlorobenzoyl chloride (DCB) in DMF/pyridine (Figure 3). This anhydride effects esterification of resin-bound hydroxyl groups in yields of typically > 70% in 18 h. Levels of D-isomer and dipeptide formation for most amino acids are typically less than 1%, with 5-acetamidomethyl cysteine giving the most enantio-merization (6.5% D-isomer) of the amino acids tested (8). 

The process of substitution undertaken on carboxylic acids and the derivatives of carboxylic acids (anhydrides, acid halides, esters, amides, and nitriles) generally involves a series of replacement processes. Thus, individually, substitution may involve replacement of (a) the proton attached to oxygen of the -OH group (i.e., ionization of the acid) (b) the hydroxyl (-OH) portion of the carboxylic acid (or derivative) (e.g., esterification) (c) the carbonyl oxygen and the hydroxyl (-OH) (e.g., orthoester formation, vide infra) (d) the entire carboxylic acid functionality (e.g., the Hunsdiecker reaction, already discussed Scheme 9.101) and the decarboxylation of orotic acid (as orotidine monophosphate) to uracil (as uridine monophosphate)—catalyzed by the enzyme orotidine monophosphate decarboxylase (Scheme 9.115) or (e) the protons (if any) on the carbon to which the carboxylic acid functional group is attached (e.g., the Dieckman cycUzation, already discussed earlier, c Equation 9.91). Indeed, processes already discussed (i.e., reduction and oxidation) have also accomplished some of these ends. Some additional substitutions for the carboxylic acid group itself are presented in Table 9.6, while other substitutions for derivatives of carboxylic acids are shown in Tables 9.7-9.10 and discussed subsequently. 

The mechanisms of the Fischer esterification and the reactions of alcohols with acyl chlorides and acid anhydrides will be discussed m detail m Chapters 19 and 20 after some fundamental principles of carbonyl group reactivity have been developed For the present it is sufficient to point out that most of the reactions that convert alcohols to esters leave the C—O bond of the alcohol intact... 

The acyl group of the carboxylic acid acyl chloride or acid anhydride is trans ferred to the oxygen of the alcohol This fact is most clearly evident m the esterification of chiral alcohols where because none of the bonds to the chirality center is broken m the process retention of configuration is observed... 

Esterification with carboxylic acid anhydrides (Section 15 8) Car... 

Acetic anhydride acetylates free hydroxyl groups without a catalyst, but esterification is smoother and more complete ia the presence of acids. For example, ia the presence of -toluenesulfonic acid [104-15-4], the heat of reaction for ethanol and acetic anhydride is —60.17 kJ/mol (—14.38 kcal/mol) (13) ... 

Butyrolactone. y-Butyrolactone [96-48-0] dihydro-2(3H)-furanone, was fkst synthesized in 1884 via internal esterification of 4-hydroxybutyric acid (146). In 1991 the principal commercial source of this material is dehydrogenation of butanediol. Manufacture by hydrogenation of maleic anhydride (147) was discontinued in the early 1980s and resumed in the late 1980s. Physical properties are Hsted in Table 4. 

Rea.ctlons, As with other tertiary alcohols, esterification with carboxyUc acids is difficult and esters are prepared with anhydrides (181), acid chlorides (182), or ketene (183). Carbamic esters may be prepared by treatment with an isocyanate (184) or with phosgene followed by ammonia or an amine (185). 

Chlorendic Acid. Chlorendic acid [115-28-6] and its anhydride [115-27-5] are widely used flame retardants. Chlorendic acid is synthesized by a Diels-Alder reaction of maleic anhydride and hexachlorocyclopentadiene (see CyclopentadlENE and dicyclopentadiente) in toluene followed by hydrolysis of the anhydride using aqueous base (60). The anhydride can be isolated directly from the reaction mixture or can be prepared in a very pure form by dehydration of the acid. The principal use of chlorendic anhydride and chlorendic acid has been in the manufacture of unsaturated polyester resins. Because the esterification rate of chlorendic anhydride is similar to that of phthalic anhydride, it can be used in place of phthalic anhydride in commercial polyester... 

The synthesis of 2,4-dihydroxyacetophenone [89-84-9] (21) by acylation reactions of resorcinol has been extensively studied. The reaction is performed using acetic anhydride (104), acetyl chloride (105), or acetic acid (106). The esterification of resorcinol by acetic anhydride followed by the isomerization of the diacetate intermediate has also been described in the presence of zinc chloride (107). Alkylation of resorcinol can be carried out using ethers (108), olefins (109), or alcohols (110). The catalysts which are generally used include sulfuric acid, phosphoric and polyphosphoric acids, acidic resins, or aluminum and iron derivatives. 2-Chlororesorcinol [6201-65-1] (22) is obtained by a sulfonation—chloration—desulfonation technique (111). 1,2,4-Trihydroxybenzene [533-73-3] (23) is obtained by hydroxylation of resorcinol using hydrogen peroxide (112) or peracids (113). 

Many of the physical properties are not affected by the optical composition, with the important exception of the melting poiat of the crystalline acid, which is estimated to be 52.7—52.8°C for either optically pure isomer, whereas the reported melting poiat of the racemic mixture ranges from 17 to 33°C (6). The boiling poiat of anhydrous lactic acid has been reported by several authors it was primarily obtained duriag fractionation of lactic acid from its self-esterification product, the dimer lactoyUactic acid [26811-96-1]. The difference between the boiling poiats of racemic and optically active isomers of lactic acid is probably very small (6). The uv spectra of lactic acid and dilactide [95-96-5] which is the cycHc anhydride from two lactic acid molecules, as expected show no chromophores at wavelengths above 250 nm, and lactic acid and dilactide have extinction coefficients of 28 and 111 at 215 nm and 225 nm, respectively (9,10). The iafrared spectra of lactic acid and its derivatives have been extensively studied and a summary is available (6). 

Esterification. Both mono- and dialkyl maleates and fumarates are obtained on treatment of maleic anhydride or its isomeric acids with alcohols or alkoxides (25). An extensive review is available (59). Alkyl fumarates (18) often are made from isomeri2ation of the corresponding maleate (19) (60). 

Commodity Phthalate Esters. The family of phthalate esters are by far the most abundandy produced woddwide. Both orthophthaUc and terephthahc acid and anhydrides are manufactured. The plasticizer esters are produced from these materials by reaction with an appropriate alcohol (eq. 1) terephthalate esterification for plasticizers is performed more abundandy in the United States. Phthalate esters are manufactured from methanol (C ) up to Qyj alcohols, although phthalate use as PVC plasticizers is generally in the range to The lower molecular weight phthalates find use in nitrocellulose the higher phthalates as synthetic lubricants for the automotive industries. 

The properties of polymers formed by the step growth esterification (1) of glycols and dibasic acids can be manipulated widely by the choice of coreactant raw materials (Table 1) (2). The reactivity fundamental to the majority of commercial resins is derived from maleic anhydride [108-31-6] (MAN) as the unsaturated component in the polymer, and styrene as the coreactant monomer. Propylene glycol [57-55-6] (PG) is the principal glycol used in most compositions, and (i9f2v (9)-phthahc anhydride (PA) is the principal dibasic acid incorporated to moderate the reactivity and performance of the final resins. 

---