Acrylonitrile temperatures

Fig-1 Emission spectra of p-pheny-lene diamine (/) and iV,N-dimethyl-p-toluidine (2) in frozen acrylonitrile (temperature 80 K)... 

A solution of 2,3-dimethylindole (145 g, 1 mol) in dry dioxan containing hydroquinone (100 mg) was treated with JV,JV,JV-trimethylbenzylammonium ethoxide (5 ml of a 40% solution in MeOH) and warmed to 35 C. Freshly distilled acrylonitrile (150 ml, 2.5 mol) was added at a rate such that the temperature did not rise above 40°C. The solution was then stirred overnight and diluted with 10% aq. acetic acid (11). The solution was extracted with CH Clj and the extract was washed with water and dried (MgS04). extract was then mixed with silica gel (800 g) and the solvent removed in vacuo. The silica was placed in a Soxhlet extractor and extracted with cyclohexane. The extract deposited the product as colourless needles (125 g, 63% yield). 

Small amounts of propionitrile and bis(cyanoethyl) ether are formed as by-products. The hydrogen ions are formed from water at the anode and pass to the cathode through a membrane. The catholyte that is continuously recirculated in the cell consists of a mixture of acrylonitrile, water, and a tetraalkylammonium salt the anolyte is recirculated aqueous sulfuric acid. A quantity of catholyte is continuously removed for recovery of adiponitrile and unreacted acrylonitrile the latter is fed back to the catholyte with fresh acrylonitrile. Oxygen that is produced at the anodes is vented and water is added to the circulating anolyte to replace the water that is lost through electrolysis. The operating temperature of the cell is ca 50—60°C. Current densities are 0.25-1.5 A/cm (see Electrochemical processing). 

The combination of durability and clarity and the ability to tailor molecules relatively easily to specific applications have made acryflc esters prime candidates for numerous and diverse applications. At normal temperatures the polyacrylates are soft polymers and therefore tend to find use in applications that require flexibility or extensibility. However, the ease of copolymerizing the softer acrylates with the harder methacrylates, styrene, acrylonitrile, and vinyl acetate, allows the manufacture of products that range from soft mbbers to hard nonfilm-forming polymers. 

Table 4 presents the solubiHty of acrylonitrile in water as a function of temperature (6). Vapor—Hquid equiHbria for acrylonitrile in combination with... 

Nitrile mbber finds broad application in industry because of its excellent resistance to oil and chemicals, its good flexibility at low temperatures, high abrasion and heat resistance (up to 120°C), and good mechanical properties. Nitrile mbber consists of butadiene—acrylonitrile copolymers with an acrylonitrile content ranging from 15 to 45% (see Elastomers, SYNTHETIC, NITRILE RUBBER). In addition to the traditional applications of nitrile mbber for hoses, gaskets, seals, and oil well equipment, new applications have emerged with the development of nitrile mbber blends with poly(vinyl chloride) (PVC). These blends combine the chemical resistance and low temperature flexibility characteristics of nitrile mbber with the stability and ozone resistance of PVC. This has greatly expanded the use of nitrile mbber in outdoor applications for hoses, belts, and cable jackets, where ozone resistance is necessary. 

Acrylonitrile has contributed the desirable properties of rigidity, high temperature resistance, clarity, solvent resistance, and gas impermeabiUty to many polymeric systems. Its availabiUty, reactivity, and low cost ensure a continuing market presence and provide potential for many new appHcations. 

Improved Hot—Wet Properties. Acryhc fibers tend to lose modulus under hot—wet conditions. Knits and woven fabrics tend to lose their bulk and shape in dyeing and, to a more limited extent, in washing and drying cycles as well as in high humidity weather. Moisture lowers the glass-transition temperature T of acrylonitrile copolymers and, therefore, crimp is lost when the yam is exposed to conditions requited for dyeing and laundering. 

Acrylonitrile—Butadiene—Styrene. Available only as sheet, ABS has good toughness and high impact resistance. It is readily therm oform able over a wide range of temperatures and can be deeply drawn. ABS has poor solvent resistance and low continuous-use temperature. It is often used in housings for office equipment (see Acrylonitrile polymers). 

MAA and MMA may also be prepared via the ammoxidation of isobutylene to give meth acrylonitrile as the key intermediate. A mixture of isobutjiene, ammonia, and air are passed over a complex mixed metal oxide catalyst at elevated temperatures to give a 70—80% yield of methacrylonitrile. Suitable catalysts often include mixtures of molybdenum, bismuth, iron, and antimony, in addition to a noble metal (131—133). The meth acrylonitrile formed may then be hydrolyzed to methacrjiamide by treatment with one equivalent of sulfuric acid. The methacrjiamide can be esterified to MMA or hydrolyzed to MAA under conditions similar to those employed in the ACH process. The relatively modest yields obtainable in the ammoxidation reaction and the generation of a considerable acid waste stream combine to make this process economically less desirable than the ACH or C-4 oxidation to methacrolein processes. 

Acrylic ESTER POLYMERS Acrylonitrile POLYMERS Cellulose esters). Engineering plastics (qv) such as acetal resins (qv), polyamides (qv), polycarbonate (qv), polyesters (qv), and poly(phenylene sulfide), and advanced materials such as Hquid crystal polymers, polysulfone, and polyetheretherketone are used in high performance appHcations they are processed at higher temperatures than their commodity counterparts (see Polymers containing sulfur). 

Blends of poly(vinyl chloride) (PVC) and a-methylstyrene—acrylonitrile copolymers (a-MSAN) exhibit a miscibiUty window that stems from an LCST-type phase diagram. Figure 3 shows how the phase-separation temperature of 50% PVC blends varies with the AN content of the copolymer (96). This behavior can be described by an appropriate equation-of-state theory and interaction energy of the form given by equation 9. 

Ammonia is used in the fibers and plastic industry as the source of nitrogen for the production of caprolactam, the monomer for nylon 6. Oxidation of propylene with ammonia gives acrylonitrile (qv), used for the manufacture of acryHc fibers, resins, and elastomers. Hexamethylenetetramine (HMTA), produced from ammonia and formaldehyde, is used in the manufacture of phenoHc thermosetting resins (see Phenolic resins). Toluene 2,4-cHisocyanate (TDI), employed in the production of polyurethane foam, indirectly consumes ammonia because nitric acid is a raw material in the TDI manufacturing process (see Amines Isocyanates). Urea, which is produced from ammonia, is used in the manufacture of urea—formaldehyde synthetic resins (see Amino resins). Melamine is produced by polymerization of dicyanodiamine and high pressure, high temperature pyrolysis of urea, both in the presence of ammonia (see Cyanamides). 

BP. These nitrile alloy membranes are compounded from PVC, flexibilized by the addition of butadiene—acrylonitrile copolymers, PVC, and other proprietary ingredients. Typically reinforced with polyester scrim, NBP membranes are 1 mm thick and have a width of 1.5 m. They ate ptedominandy used in mechanically fastened roofing systems. NBP membranes exhibit excellent teat and puncture resistance as well as good weatherabihty, and remain flexible at low temperatures. They ate resistant to most chemicals but ate sensitive to aromatic hydrocarbons. The sheet is usually offered in light colors. The physical characteristics of NBP membranes have been described (15). 

Nitrile Rubber. Nitrile mbbers are made by the emulsion copolymerization of acrylonitrile (9—50%) and butadiene (6) and designated NBR. The ratio of acrylonitrile (ACN) to butadiene has a direct effect on the properties on the nature of the polymers. As the ACN content increases, the oil resistance of the polymer increases (7). As the butadiene content increases, the low temperature properties of the polymer are improved (see Elastomers, SYNTHETIC-NITRILE RUBBER). 

By comparison, temperatures as high as 150°C are often required for mold-enclosed hard natural mbber compounds, where mold plattens are directly heated by steam or electricity. Synthetic latex mbber compounds, however, can be vulcanised at temperatures higher than those for natural mbber neoprene and acrylonitrile—butadiene can be vulcanised at as high as 135°C. 

The properties of PVDC (Table 3) ate usually modified by copolymerization. Copolymers of high VDC content have lower melting temperatures than PVDC. Copolymers containing mote than mol % acrylate or methacrylate ate amorphous. Substantially mote acrylonitrile (25%) or vinyl chloride (45%) is required to destroy crystallinity completely. 

Fig. 3. Effect of comonomer stmcture on the glass-transition temperature of VDC copolymers (72), where A represents acrylonitrile B, methyl acrylate ...

---