Acrylonitrile polyacrylonitrile

Acrylonitrile Polyacrylonitrile (PAN) Rugs Orion and Acrilan are copolymers with other monomers... 

GH2=GHGN Acrylonitrile Polyacrylonitrile, Orion acrylics and acrylates... 

Acrylonitrile is also often copolymerized with other monomers to form fibers. These acrylic fibers have good abrasion resistance, flex life, toughness, and high strength. They have good resistance to stains and moisture. Modacrylic fibers contain between 35 and 85 percent acrylonitrile. Polyacrylonitrile polymers are also used as precursors to carbon fibers. 

Only if the polymer is insoluble in its own monomer such as vinyl chloride/poly (vinyl chloride) or acrylonitrile/polyacrylonitrile. 

CH2=CHCN Acrylonitrile Polyacrylonitrile, Orion acrylic and acrylate plastics... 

The principal monomer of nitrile resins is acrylonitrile (see Polyacrylonitrile ), which constitutes about 70% by weight of the polymer and provides the polymer with good gas barrier and chemical resistance properties. The remainder of the polymer is 20 to 30% methylacrylate (or styrene), with 0 to 10% butadiene to serve as an impact-modifying termonomer. 

Resin and Polymer Solvent. Dimethylacetamide is an exceUent solvent for synthetic and natural resins. It readily dissolves vinyl polymers, acrylates, ceUulose derivatives, styrene polymers, and linear polyesters. Because of its high polarity, DMAC has been found particularly useful as a solvent for polyacrylonitrile, its copolymers, and interpolymers. Copolymers containing at least 85% acrylonitrile dissolve ia DMAC to form solutions suitable for the production of films and yams (9). DMAC is reportedly an exceUent solvent for the copolymers of acrylonitrile and vinyl formate (10), vinylpyridine (11), or aUyl glycidyl ether (12). 

The first reported synthesis of acrylonitrile [107-13-1] (qv) and polyacrylonitrile [25014-41-9] (PAN) was in 1894. The polymer received Htde attention for a number of years, until shortly before World War II, because there were no known solvents and the polymer decomposes before reaching its melting point. The first breakthrough in developing solvents for PAN occurred at I. G. Farbenindustrie where fibers made from the polymer were dissolved in aqueous solutions of quaternary ammonium compounds, such as ben2ylpyridinium chloride, or of metal salts, such as lithium bromide, sodium thiocyanate, and aluminum perchlorate. Early interest in acrylonitrile polymers (qv), however, was based primarily on its use in synthetic mbber (see Elastomers, synthetic). 

The principal use of the peroxodisulfate salts is as initiators (qv) for olefin polymerisation in aqueous systems, particularly for the manufacture of polyacrylonitrile and its copolymers (see Acrylonitrile polymers). These salts are used in the emulsion polymerisation of vinyl chloride, styrene—butadiene, vinyl acetate, neoprene, and acryhc esters (see Acrylic ester polymers Styrene Vinyl polymers). 

Heterogeneous polymerization is characteristic of a number of monomers, including vinyl chloride and acrylonitrile. A completely satisfactory mechanism for these reactions has not been deterrnined. This is tme for VDC also. Earlier studies have not been broad enough to elucidate the mechanism (26,30,31). Morphologies of as-polymerized poly(vinyl chloride) (PVC) and polyacrylonitrile (PAN) are similar, suggesting a similar mechanism. 

Fig. 15. Oxygen permeability versus 1/specific free volume at 25 °C (30). 1. Polybutadiene 2. polyethylene (density 0.922) 3. polycarbonate 4. polystyrene 5. styrene-acrylonitrile 6. poly(ethylene terephthalate) 7. acrylonitrile barrier polymer 8. poly(methyl methacrylate) 9. poly(vinyl chloride) 10. acrylonitrile barrier polymer 11. vinyUdene chloride copolymer 12. polymethacrylonitrile and 13. polyacrylonitrile. See Table 1 for unit conversions.

This combination of monomers is unique in that the two are very different chemically, and in thek character in a polymer. Polybutadiene homopolymer has a low glass-transition temperature, remaining mbbery as low as —85° C, and is a very nonpolar substance with Htde resistance to hydrocarbon fluids such as oil or gasoline. Polyacrylonitrile, on the other hand, has a glass temperature of about 110°C, and is very polar and resistant to hydrocarbon fluids (see Acrylonitrile polymers). As a result, copolymerization of the two monomers at different ratios provides a wide choice of combinations of properties. In addition to providing the mbbery nature to the copolymer, butadiene also provides residual unsaturation, both in the main chain in the case of 1,4, or in a side chain in the case of 1,2 polymerization. This residual unsaturation is useful as a cure site for vulcanization by sulfur or by peroxides, but is also a weak point for chemical attack, such as oxidation, especially at elevated temperatures. As a result, all commercial NBR products contain small amounts ( 0.5-2.5%) of antioxidant to protect the polymer during its manufacture, storage, and use. 

Solution Polymerization These processes may retain the polymer in solution or precipitate it. Polyethylene is made in a tubular flow reactor at supercritical conditions so the polymer stays in solution. In the Phillips process, however, after about 22 percent conversion when the desirable properties have been attained, the polymer is recovered and the monomer is flashed off and recyled (Fig. 23-23 ). In another process, a solution of ethylene in a saturated hydrocarbon is passed over a chromia-alumina catalyst, then the solvent is separated and recyled. Another example of precipitation polymerization is the copolymerization of styrene and acrylonitrile in methanol. Also, an aqueous solution of acrylonitrile makes a precipitate of polyacrylonitrile on heating to 80°C (176°F). 

Because the polymer degrades before melting, polyacrylonitrile is commonly formed into fibers via a wet spinning process. The precursor is actually a copolymer of acrylonitrile and other monomer(s) which are added to control the oxidation rate and lower the glass transition temperature of the material. Common copolymers include vinyl acetate, methyl acrylate, methyl methacrylate, acrylic acid, itaconic acid, and methacrylic acid [1,2]. 

The commercial fibers are produced from rayon, polyacrylonitrile, and petroleum pitch. When acrylonitrile is heated in air at moderate temperatures (= 220°C ), HCN is lost, and a ladder polymer is thought to be the intermediate ... 

The second group includes SAHs obtained by radical grafting of acrylonitrile (AN) on natural polymers, mostly starch, under the action of cerium initiators [43 -46, 50, 51], The proper crosslinked hydrophilic polymer is formed at the stage of alkali hydrolysis of grafted polyacrylonitrile (PAN), the final characteristics depending on many factors, in particular the sort of starch [46], the methods of its preparation [51], the component ratio, etc. The nature of starch is exhibited through... 

SBR (Styrene Butadiene Rubber) ABS (Acrylonitrile Butadiene Styrene Polymethyl methacrylate PAN (Polyacrylonitrile)... 

Acrylonitrile, CH,CHCN, is used in the synthesis of acrylic fibers (polyacrylonitriles), such as Orion. Write the Lewis structure of acrylonitrile and describe the hybrid orbitals on each carbon atom. What are the approximate values of the bond angles ... 

The principal use of acrylonitrile since the early 1950s has been in the manufacture of so-called acrylic textile fibers. Acrylonitrile is first polymerized to polyacrylonitrile, which is then spun into fiber. The main feature of acrylic fibers is their wool-like characteristic, making them desirable for socks, sweaters, and other types of apparel. However, as with all synthetic textile fibers, fashion dictates the market and acrylic fibers currently seem to be in disfavor, so this outlet for acrylonitrile may be stagnant or declining. The other big uses for acrylonitrile are in copolymers, mainly with styrene. Such copolymers are very useful for the molding of plastic articles with very high impact resistance. 

Polyacrylonitrile, known commercially as Orion, is made by polymerizing acrylonitrile (see Figure 13-3) Orion is used to make fibers for carpeting and clothing. Draw the Lewis structure of polyacrylonitrile, showing at least three repeat units. 

Acrylonitrile polymerizes in the same way as ethylene. Notice that this polymer has the same structure as polyethylene, except that a CN group is attached to every second carbon atom, so the structure is a reasonable one. A line structure of polyacrylonitrile eliminates the clutter caused by the H atoms. A ball-and-stick model of the same polymer segment is included for comparison. 

There are two pathways for the degradation of nitriles (a) direct formation of carboxylic acids by the activity of a nitrilase, for example, in Bacillus sp. strain OxB-1 and P. syringae B728a (b) hydration to amides followed by hydrolysis, for example, in P. chlororaphis (Oinuma et al. 2003). The monomer acrylonitrile occurs in wastewater from the production of polyacrylonitrile (PAN), and is hydrolyzed by bacteria to acrylate by the combined activity of a nitrilase (hydratase) and an amidase. Acrylate is then degraded by hydration to either lactate or P-hydroxypropionate. The nitrilase or amidase is also capable of hydrolyzing the nitrile group in a number of other nitriles (Robertson et al. 2004) including PAN (Tauber et al. 2000). 

Polymerization of acrylonitrile adsorbed on polyacrylonitrile" An intimate mixture of polyacrylonitrile solvated by its monomer is obtained if one melts acrylonitrile crystals which have been subjected to high energy radiation at low temperatures. The polymer forms under irradiation within the crystal lattice and upon melting, a gel-like phase is obtained in which the individual polymer molecules do not aggregate, presumably because most of the CN groups are then associated in pairs with the -CN groups of the monomer. Such a polyacrylonitrile solvated by its monomer should indeed be an ideal medium for the matrix effect to operate. 

---