Acetone, reaction with

What would be the effect of carrying out the sodium iodide in acetone reaction with the alkyl halides using an iodide solution half as concentrated ... 

Reaction of HjPtGlg with benzene in aq CF3CO2H acid gives the phenyl analog of I in 40% yield after workup from acetone . Reactions with toluene, ethylbenzene, chlorobenzene and anisole give inseparable mixtures of meta and para products in which the meta/para ratio varies in different runs of the same reaction. As in the C—H oxidative addition reactions in 5.8.2.6.4, no ortho product is observed. 

For the Ni-ALPON catalyst, acetone reaction with hydrogen was carried out in a fixed bed reactor operating at 1 atm and 200 °C with a feed stream containing 20 mol% acetone in H2. Prior to catalytic activity measurements, samples were H2 (100 cm mim ) reduced at 400 C. After heating to 400 °C at a rate of 8 °Cmin-, the time on stream of the isothermal part of the treatment was varied between 0 and 12 h. The W/Fao ratio was kept constant for all experiments, and was equal to 0.647 gear h mol acetone Selectivities were defined as the molar fraction of the reacted acetone which was converted into a given product. 

Reaction of the cnrbaiilon (acetone anion) with the carbonyl carbon of ethyl acetate, accompanied by the release of an ethoxide ion, to form acetyl-acetone ... 

In all its reactions the lone pair of thiazole is less reactive than that of pyridine. Table 1-61 shows three sets of physicochemical data that illustrate this difference. These are (1) the thermodynamic basicity, which is three orders of magnitude lower for thiazole than for pyridine (2) the enthalpy of reaction with BF3 in nitrobenzene solution, which is 10% lower for thiazole than for pyridine and (3) the specific rate of quaterni-zation by methyl iodide in acetone at 40°C, which is about 50% lower for... 

Arrange the isomers of molecular formula C4H9CI in order of decreasing rate of reaction with sodium iodide in acetone... 

Acetone cracks to ketene, and may then be converted to anhydride by reaction with acetic acid. This process consumes somewhat less energy and is a popular subject for chemical engineering problems (24,25). The cost of acetone works against widespread appHcation of this process, however. 

With aldehydes, primary alcohols readily form acetals, RCH(OR )2. Acetone also forms acetals (often called ketals), (CH2)2C(OR)2, in an exothermic reaction, but the equiUbrium concentration is small at ambient temperature. However, the methyl acetal of acetone, 2,2-dimethoxypropane [77-76-9] was once made commercially by reaction with methanol at low temperature for use as a gasoline additive (5). Isopropenyl methyl ether [116-11-OJ, useful as a hydroxyl blocking agent in urethane and epoxy polymer chemistry (6), is obtained in good yield by thermal pyrolysis of 2,2-dimethoxypropane. With other primary, secondary, and tertiary alcohols, the equiUbrium is progressively less favorable to the formation of ketals, in that order. However, acetals of acetone with other primary and secondary alcohols, and of other ketones, can be made from 2,2-dimethoxypropane by transacetalation procedures (7,8). Because they hydroly2e extensively, ketals of primary and especially secondary alcohols are effective water scavengers. 

Ketones with labile hydrogen atoms undergo enol acetylation on reaction with ketene. Strong acid catalysis is required. If acetone is used, isoptopenyl acetate [108-22-5] (10) is formed (82—85). Isopropenyl acetate is the starting material for the production of 2,4-pentanedione (acetylacetone) [123-54-6] (11). 

Furalazine, Acetylfuratrizine, Panfuran-S. Heating nitrovin in butanol or dimethylformamide at 100—130°C affords furalazine, 6-[2-(5-nitro-2-furanyl)ethenyl]-l,2,4-triazine-3-amine (34). An improved synthesis originates with 5-nitro-2-furancarboxaldehyde and acetone, proceeds through 4-(5-nitro-2-furanyl)-3-buten-2-one followed by a selenium dioxide oxidation to the pymvaldehyde hydrate, and subsequent reaction with aininoguariidine (35). Furalazine, acetylfuratrizine (36), and the A[-A/-bis(hydroxymethyl) derivative, Panfuran-S, formed from the parent compound and formaldehyde (37), are systemic antibacterial agents. 

Carbonyl Compounds. Cychc ketals and acetals (dioxolanes) are produced from reaction of propylene oxide with ketones and aldehydes, respectively. Suitable catalysts iaclude stannic chloride, quaternary ammonium salts, glycol sulphites, and molybdenum acetyl acetonate or naphthenate (89—91). Lactones come from Ph4Sbl-cataly2ed reaction with ketenes (92). 

Linalool can be converted to geranyl acetone (63) by the CarroU reaction (34). By transesterification with ethyl acetoacetate, the intermediate ester thermally rearranges with loss of carbon dioxide. Linalool can also be converted to geranyl acetone by reaction with methyl isopropenyl ether. The linalyl isopropenyl ether rearranges to give the geranyl acetone. 

Trichloroacetone [921-03-9] (13a) is prepared by chlorination of acetone. The reaction is nonselective and the required compound is isolated by distillation. The selectivity has been improved by catalyzing the reaction with iodine (31). 

Acetalation. As polyhydroxy compounds, carbohydrates react with aldehydes and ketones to form cycHc acetals (1,13). Examples are the reaction of D-glucose with acetone and a protic or Lewis acid catalyst to form l,2 5,6-di-0-isoprop5lidene-a-D-glucofuranose [582-52-5] and its reaction with benzaldehyde to form 4,6-0-benzyhdene-D-glucopyranose [25152-90-3]. The 4,6-0-(l-carboxyethyhdine) group (related to pymvic acid) occurs naturally in some polysaccharides. 

Reaction of HOCl, formed from calcium hypochlorite and CO2, with highly substituted alkenes in CH2CI2 is a convenient route to aHyUc chlorides (111). Ketones are chlorinated to a-chloroketones by reaction with HOCl Acetone initially gives CH2COCH2CI (112). Methyl ethyl ketone gives 78% CH3CHCICOCH3, 15% CH3CH2COCH2CI, and 7% dichlorides (113). 

Chloroform can be manufactured from a number of starting materials. Methane, methyl chloride, or methylene chloride can be further chlorinated to chloroform, or carbon tetrachloride can be reduced, ie, hydrodechlorinated, to chloroform. Methane can be oxychlorinated with HCl and oxygen to form a mixture of chlorinated methanes. Many compounds containing either the acetyl (CH CO) or CH2CH(OH) group yield chloroform on reaction with chlorine and alkali or hypochlorite. Methyl chloride chlorination is now the most common commercial method of producing chloroform. Many years ago chloroform was almost exclusively produced from acetone or ethyl alcohol by reaction with chlorine and alkali. 

Another appHcation of 4-chlorophenol is in the synthesis of a dmg, ethyl a, a-dimethyl-4-chlorophenoxy acetate [637-07-0] (60), used as a cholesterol-reducing agent. This synthesis involves reaction with acetone and chloroform, followed by ethanol esterification. 

Other modifications of the polyamines include limited addition of alkylene oxide to yield the corresponding hydroxyalkyl derivatives (225) and cyanoethylation of DETA or TETA, usuaHy by reaction with acrylonitrile [107-13-1/, to give derivatives providing longer pot Hfe and better wetting of glass (226). Also included are ketimines, made by the reaction of EDA with acetone for example. These derivatives can also be hydrogenated, as in the case of the equimolar adducts of DETA and methyl isobutyl ketone [108-10-1] or methyl isoamyl ketone [110-12-3] (221 or used as is to provide moisture cure performance. Mannich bases prepared from a phenol, formaldehyde and a polyamine are also used, such as the hardener prepared from cresol, DETA, and formaldehyde (228). Other modifications of polyamines for use as epoxy hardeners include reaction with aldehydes (229), epoxidized fatty nitriles (230), aromatic monoisocyanates (231), or propylene sulfide [1072-43-1] (232). 

---