Absorption, interferences selective

In practice, one usually deals with multicomponent samples. The analysis is done on the basis of the individual spectra and measurements performed at properly selected wavelengths to reduce absorption interferences. Apart from the PA signal amplitude the PA phase yields additional information for the analysis. A broad tuning range of the laser source and a narrow line width are advantageous for obtaining a high selectivity which is further enhanced for species with well structured spectra. 

A wavelength selector that uses either absorption, or constructive and destructive interference to control the range of selected wavelengths. 

A simple instrument for measuring absorbance that uses absorption or interference filters to select the wavelength. 

Selectivity The selectivity of molecular fluorescence and phosphorescence is superior to that of absorption spectrophotometry for two reasons first, not every compound that absorbs radiation is fluorescent or phosphorescent, and, second, selectivity between an analyte and an interferant is possible if there is a difference in either their excitation or emission spectra. In molecular luminescence the total emission intensity is a linear sum of that from each fluorescent or phosphorescent species. The analysis of a sample containing n components, therefore, can be accomplished by measuring the total emission intensity at n wavelengths. 

Atomic emission is used for the analysis of the same types of samples that may be analyzed by atomic absorption. The development of a quantitative atomic emission method requires several considerations, including choosing a source for atomization and excitation, selecting a wavelength and slit width, preparing the sample for analysis, minimizing spectral and chemical interferences, and selecting a method of standardization. 

Hardness can also be calculated by summation of the individually deterrnined alkaline earths by means of atomic absorption analysis. Basic samples must be acidified, and lanthanum chloride must be added to minimise interferences from phosphate, sulfate, and aluminum. An ion-selective electrode that utilizes ahquid ion exchanger is also available for hardness measurement however, this electrode is susceptible to interferences from other dissolved metal ions. 

I have carried out widespread studies on the application of a sensitive and selective preconcentration method for the determination of trace a mounts of nickel by atomic absorption spectrometry. The method is based on soi ption of Cu(II) ions on natural Analcime Zeolit column modified with a new Schiff base 5-((4-hexaoxyphenylazo)-N-(n-hexyl-aminophenyl)) Salicylaldimine and then eluted with O.IM EDTA and determination by EAAS. Various parameters such as the effect of pH, flow rate, type and minimum amount of stripping and the effects of various cationic interferences on the recovery of ions were studied in the present work. 

With interference filters two narrow wavelength bands are selected. These are the absorption (or measurement) and reference bands, within which the gas absorption is as high and as low as possible. The filters are mounted on a rotating disk, and the intensities are registered synchronously. The ratio of the intensities is used as the signal related to the gas concentration (Fig, 1... 

Spectral interferences in AAS arise mainly from overlap between the frequencies of a selected resonance line with lines emitted by some other element this arises because in practice a chosen line has in fact a finite bandwidth . Since in fact the line width of an absorption line is about 0.005 nm, only a few cases of spectral overlap between the emitted lines of a hollow cathode lamp and the absorption lines of metal atoms in flames have been reported. Table 21.3 includes some typical examples of spectral interferences which have been observed.47-50 However, most of these data relate to relatively minor resonance lines and the only interferences which occur with preferred resonance lines are with copper where europium at a concentration of about 150mgL 1 would interfere, and mercury where concentrations of cobalt higher than 200 mg L 1 would cause interference. 

With flame emission spectroscopy, there is greater likelihood of spectral interferences when the line emission of the element to be determined and those due to interfering substances are of similar wavelength, than with atomic absorption spectroscopy. Obviously some of such interferences may be eliminated by improved resolution of the instrument, e.g. by use of a prism rather than a filter, but in certain cases it may be necessary to select other, non-interfering, lines for the determination. In some cases it may even be necessary to separate the element to be determined from interfering elements by a separation process such as ion exchange or solvent extraction (see Chapters 6, 7). 

Apart from the interferences which may arise from other elements present in the substance to be analysed, some interference may arise from the emission band spectra produced by molecules or molecular fragments present in the flame gases in particular, band spectra due to hydroxyl and cyanogen radicals arise in many flames. Although in AAS these flame signals are modulated (Section 21.9), in practice care should be taken to select an absorption line which does not correspond with the wavelengths due to any molecular bands because of the excessive noise produced by the latter this leads to decreased sensitivity and to poor precision of analysis. 

X-ray absorption spectroscopy combining x-ray absorption near edge fine structure (XANES) and extended x-ray absorption fine structure (EXAFS) was used to extensively characterize Pt on Cabosll catalysts. XANES Is the result of electron transitions to bound states of the absorbing atom and thereby maps the symmetry - selected empty manifold of electron states. It Is sensitive to the electronic configuration of the absorbing atom. When the photoelectron has sufficient kinetic energy to be ejected from the atom It can be backscattered by neighboring atoms. The quantum Interference of the Initial... 

Puacz et al. (1995) developed a catalytic method, based on the iodine-azide reaction, for the determination of hydrogen sulfide in human whole blood. The method involves the generation of hydrogen sulfide in an evolution-absorption apparatus. In addition, the method allows for the determination of sulfide in blood without interference from other sulfur compounds in blood. A detection limit of 4 g/dm3 and a percent recovery of 98-102% were achieved. Although the accuracy and precision of the catalytic method are comparable to those of the ion-selective electrode method, the catalytic method is simpler, faster, and would be advantageous in serial analysis. 

Figure 12.7.1 The phenomena of light reflection, absorption, and interference to create the appearance of color. Color arises as certain wavelengths of reflected light are selectively reinforced through constructive interference, while other wavelengths of light are canceled through destructive interference.

---