Weight Percentage composition

Table 8.2 Weight percentage composition of glasses in various commercial conventional glass-ionomer cements... 

Weight Percentage Composition of HEAR and LEAR Lipids and Phospholipid Components"... 

He also gives the volume and weight percentage compositions of 17 gases and vapours, the volumes of the constituents in 100 vols. being ... 

What is the weight percentage composition of the elementary constituents of ethanol, C2H5OH ... 

DRIFT spectroscopy of microscopic amounts of dye mixtures extracted from small textile samples has been reported raw and pretreated data matrices were interpreted with the use of chemomet-rics (PCA, SIMCA, FC) [145]. DRIFTS can readily detect 200 ng quantities of pure, standard dyes. Bridge et al. [42] have qualitatively characterised acid dyes (Cl Acid Red 17, Red 18, Red 44, Red 88, Blue 45 and Yellow 17) applied to wool and nylon. Near-infrared diffuse reflectance spectroscopy was evaluated for its ability to analyse solid antioxidant blends [146]. These opaque materials do not transmit near-IR light. This fast method effectively predicts weight percentage composition with a precision comparable to the currently accepted HPLC method of analysis, and can identify blend types and contaminated materials. 

Plant-fiber identification is described in TAPPI T8 and TIO. In order to identify synthetic fibers, it usually is necessary to conduct solubihty and physical properties tests in addition to light microscopy observations. Systematic sampling is required to obtain quantitative information on sample composition. Because different types of pulps contain varying numbers of fibers per unit weight, it is necessary to multiply the total number of each kind of fiber by a relative weight factor, thereby the weight percentage that each fiber type contributes to the sample can be deterrnined. 

Although the mbbery properties of ethylene—propylene copolymers are exhibited over a broad range of compositions, weight percentages of commercial products generally range from 50 50 to 75 25 ethylene propylene. 

Type of waste Heating value, Btu/lb Percentage composition by weight Density, Ib/fF... 

Certain thermodynamic relations exist between the state variables. In general for a binary alloy we choose p, T and Xg (the at% of component B) as the independent variables - though presently we shall drop p. The volume 1/ and the composition Xa (= 1 - Xg) are then determined they are the dependent variables. Of course, the weight percentages Wa and Wg can be used instead. 

If listed toxic chemicals are present equal to or above the de minimis cut-off level, your supplier must identify the specific components as they appear in Table II and provide their percentage composition by weight in the mixture or product, tf your supplier maintains that the identity ot a toxic chemical is a trade secret, a generic identity that is structurally descriptive must be supplied on the notice. A maximum concentration level must be provided if your supplier contends that chemical composition information is a trade secret. In either case, you do not need to make a trade secret claim on behalf of your supplier (unless you consider your use of the proprietary mixture a trade secret). On Form R, identify the toxic chemical you are reporting according to its generic name provided in the notification. (See the instructions for Part III, Section 2 on page 18 for more information.) tf the listed chemical is present below the de minimis level, no notification is required. 

Prepare a mixture, by weight, of A with compound (IV). Inject a 0.3 pL sample of this mixture, measure the various peak areas and, after making appropriate corrections for differences in detector sensitivity, determine the percentage composition of A. 

Table II. Carbohydrate compositions (weight percentage) of individual oligomer peaks purified (QAE-Sephadex or HPLC ion-exchange separation, respectively) from mixtures of citrus pectin oligomers or B fruit extracts Compositions shown are for peaks whose biological activity is described in Figure 4. Uronic acid values are based on colorimetric assay. Proportions of neutral sugars were determined by GC and adjusted so that totals equal 100%. In fact, some oligomers (G7 peaks 8, 9 and 10. B extract peak 10) produced small (less than 1 % of the total integrated area), unknown peaks in the GC chromatograms.

Feed composition, weight percentage water 2.4, aniline 73.0, nitrobenzene 3.2, cyclo-hexylamine trace. 

The hydrogenated (H) block copolymers will be designated by giving the butadiene (B) or isoprene (i) block sequence followed by a number which represents the total weight percentage of butadiene in the polymer. For example HBIB-27 is a hydrogenated triblock copolymer of butadiene-isoprene-butadiene which contains 27% butadiene. Since the polymer is symmetric, the relative composition of each block is therefore 13.5% B -73% I -13.5% B. 

Fraction Percentage lipid Percentage composition by dry weight Transport role... 

Normalization. Each peak is weighted to its fractional (or percentage) composition. This weighting prevents samples with large total concentrations from heavily influencing an analysis. Also, this scaling technique focuses the classification on questions about variations in relative composition of samples independently of the absolute concentration measured. Although... 

Composition and Heating Value Coal analyses are reported on several bases, and it is customary to select the basis best suited to the application. The as-recewed basis represents the weight percentage of each constituent in the sample as received in the laboratory. The sample itself may be coal as fired, as mined, or as prepared for a particular use. The moisture-free (dry) basis is a useful basis because performance calculations can be easily corrected for the actual moisture content at the point of use. The dry, ash-free basis is frequently used to approximate the rank and source of a coal. For example, the heating v ue of coal from a given deposit is remarkably constant when calculated on this basis. 

A chemical formula may be used to compute the percentage composition of a compound that is, the percentage by weight of each type of atom in the compound. 

Find the percentage composition of (the percentage by weight of each element... 

A mixture ofN2 and H2 jjas a density ofO 267 g/hter at 700 torr and 30°C por this mixture, calculate (a) the apparent molecular weight, (b) the percentage composition by volume, and (c) the number of molecules in one ml... 

If you completed only parts A, C, and D, it is possible to identify all the fatty acids present and to calculate the composition in weight percentage. 

The percentage composition of carotenoids in plants depends on growing conditions. The average weight percent ranges are /3-carotene, 25-40% lutein, 40-60% violaxanthin, 10-20% and neoxanthin, 5-13%. Carotenoids are biosynthesized by condensation of acetyl CoA through the mevalonic acid pathway and the Porter-Lincoln pathway. 

---