Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Water molecular weight

Fig. 4. Upper temperature limit for solubiUty of poly(ethylene oxide) in water. Molecular weight is 2 x 10 (3). Fig. 4. Upper temperature limit for solubiUty of poly(ethylene oxide) in water. Molecular weight is 2 x 10 (3).
Absolute humidity H equals the pounds of water vapor carried by 1 lb of diy air. If ideal-gas behavior is assumed, H = M p/[M P — p)], where M,, = molecular weight of water = molecular weight of air p = partial pressure of water vapor, atm and P = total pressure, atm. [Pg.1151]

Ethyl laurate-water Molecular weight cutoff = 500Da, Product name BM5, Berghof 116... [Pg.566]

A solution of glucose (molecular weight 180.16) in water (molecular weight 18.01) is prepared. The mole fraction of glucose in the solution is 0.100. What is the molality of... [Pg.212]

This same research group also reported [318] the cationic polymerization of p-methoxystyrene in miniemulsion. DBSA was used as both a protonic initiator and surfactant. A monomer conversion of 100% was achieved in eight hours at 60 °C. Molecular weights were low (approximately 1,000) and solids of up to 40% could be achieved with good colloidal stability. Polymerization takes place at the interface, initiated by the proton, and terminated by water. Molecular weight increased with conversion, suggesting either reversible termination or decreasing termination. [Pg.243]

Ethyl benzene flow rate Ethyl benzene molecular weight Steam flow rate Water molecular weight Mixed feed temperature Inlet pressure Final conversion... [Pg.416]

Fig. 8. Dependence of on temperature for poly-(dimethoxyethylene) (PDME) in water. Molecular weight of the polymer M 1 80000, 2 25000, tjred = 0-89 cP... Fig. 8. Dependence of on temperature for poly-(dimethoxyethylene) (PDME) in water. Molecular weight of the polymer M 1 80000, 2 25000, tjred = 0-89 cP...
For convenience, the amount of a species in solution is often expressed as a molality rather than as a mole fraction. The molality of a solute is its amount in moles per kilogram of solvent. For an aqueous solution containing n moles of solute and nw moles of water (molecular weight 0.018 kg mol-1) the molality, m, , of the solute is... [Pg.447]

The moles is a defined unit in the SI system such that i mol is an amount of matter that contains exactly IVa molecules, where Na = 6.022 x 10 3 mol is Avogadro s number.fi The mass of 1 mol is the molar mass and is numerically equal to the molecular weight multiplied by lo-skg. For example, the molar mass of water (molecular weight 18.015) is... [Pg.35]

Acid / Salt pK value Solubility in water Molecular weight (g) Gross energy (KJ/g) Physical condition... [Pg.2]

Henry s constant is a measure of the escaping tendency of a solvent from a very dilute solution. It is given by a simple equation Henry s constant = p x ( t where p is the pressure of pure solvent at the solution temperature and ( ) is the solvent concentration in the liquid phase. A high value of Henry s constant indicates that solvent can be easily stripped from dilute water solution. It can also be used to calculate TLV levels by knowing concentration of a solvent in a solution according to the equation TLV (in ppm) = [18 H (concentration of solvent in water)]/ molecular weight of solvent. [Pg.64]

Fig. 3 Dynamic test frequency oscillation sweep. For viscoelastic fluid of 1 wt% poly (ethylene-oxide)(PEO) in 55 wt% glycerol water. Molecular weight of PEO is 2 X 10 g/mol... Fig. 3 Dynamic test frequency oscillation sweep. For viscoelastic fluid of 1 wt% poly (ethylene-oxide)(PEO) in 55 wt% glycerol water. Molecular weight of PEO is 2 X 10 g/mol...
Kinetic studies on the radiation-induced polymerization and post-polymerization of TFE were carried out using chlorofluorohydrocarbons as solvents. The remarkable postpolymerization is again explained by the unusually slow rate of the bimolecular chain termination. A chain transfer reaction was also discussed by Hisasue et al. [721]. Suwa et al. [679] discussed the emulsion polymerization of TFE by radiation with ammonium perfluorooctanoate (FC-143) as the emulsifier. The polymerization rate is proportional to the 0.8 power of the dose rate and is almost independent of the emulsifier concentration (up to 2wt% in water). Molecular weights between 10 and 10 were observed, which increases with reaction time but decreases with the emulsifier concentration. In general, the molecular weight of PTFE prepared by radiation-induced polymerization in solution and in emulsion is relatively low compared with commercial PTFE. However, it is also possible to produce molecular weight of up to 3 x 10 if an emulsifier-free polymerization are carried out [677,678,723]. [Pg.225]

Under some circumstances, such as when the bubble size is very small and low gas flow rates are used, the concentrations of the VOCs in all phases are at thermodynamic equilibrium. In this case, the removal kinetics of the VOCs is given by Eq. (11) [82-84], where t is the removal time and k is the apparent removal rate constant, given by Eq. (12) [84]. is the water molecular weight, E is the mass of latex in the devolatilizer, and X is the mass fraction of polymer in the latex. [Pg.986]

Here - the water molecular weight, Pl - the water density in the liquid phase,... [Pg.69]


See other pages where Water molecular weight is mentioned: [Pg.283]    [Pg.48]    [Pg.153]    [Pg.193]    [Pg.283]    [Pg.406]    [Pg.2203]    [Pg.180]    [Pg.32]    [Pg.2187]    [Pg.296]    [Pg.482]    [Pg.123]    [Pg.155]    [Pg.1175]    [Pg.441]    [Pg.1428]    [Pg.150]    [Pg.120]    [Pg.990]    [Pg.343]    [Pg.29]    [Pg.6]    [Pg.214]   
See also in sourсe #XX -- [ Pg.232 ]

See also in sourсe #XX -- [ Pg.22 ]

See also in sourсe #XX -- [ Pg.2 ]

See also in sourсe #XX -- [ Pg.87 ]




SEARCH



High molecular weight polyethers water content

Low-molecular-weight water-soluble chitosan

Molecular water

Molecular weight of water vapor

Molecular weight standards water soluble

Molecular weight water-soluble

Molecular weight water-soluble organic matter

Water weight

Water-soluble cellulose ether molecular weight

© 2024 chempedia.info