Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Upper mold half

Replacement of upper mold half — PP integral skin foam still a long way from satisfying current standards... [Pg.338]

In positive type mold makes, the force in the upper mold half is allowed to enter the cavity in the lower half with a tight fit between the two components, thus providing direct and positive pressure on the compound in the mold cavity as well... [Pg.71]

Such bobbins may be molded with the cylindrical body axis parallel to the parting surface of the mold. The cavity of the bottom half has the half-round shape to mold half of the body of the bobbin, as well as two thin slots at each end to mold half of each flange. The upper mold half... [Pg.470]

Light RTM (LRTM) The upper mold half is made from semi-transparent composite shell which may be supported by a steel structure. LRTM was developed to reduce the tooling cost in RTM, and also shorten the labor time of vacuum-bagging in VARTM and thus shorten the cycle time. [Pg.250]

Compression mold upper mold half (male mold or force) (2) press table (3) press cylinder (4) press tie bars (5) compression mold lower mold half (female mold) (6) compression molding brace (7) ejector cylinder... [Pg.80]

Transfer piston (2) transfer cyiinder (3) fiash opening (4) external clamping (5) upper mold half (6) lower mold half... [Pg.84]

Test mold for transfer molding process (1) Upper clamping plate (2) transfer piston (3) external clamping (4) mold core (5) transfer cylinder (6) bypass channel (7) mold leader pin (8) upper mold half (9) hand grip (10) lower mold half (11) lower clamping plate... [Pg.87]

Upper mold half (2) loading chamber (3) shut-off edge (4) lower mold half... [Pg.89]

Dovetailed sliders (2) ejector plate (3) upper mold half (4) split cavity ... [Pg.92]

FIGURE 1.99 Upper mold half [Picture Buderus Edelstahl GmbH/Peguform]... [Pg.104]

Especially for larger components, the mixing head is attached to the upper mold half for accessibility. The position of the gate should be chosen so the flow path end of all flow paths can be reached at the same time. A position very deep inside the mold is preferable to avoid swirls and shifting due to the down-flowing and rising foam as much as possible. [Pg.112]

Upper mold half (for self-locking molds often rotatable)... [Pg.115]

Lower mold half (2) upper mold half (3) front of the mold (4) slider, flap (5) swivel cylinder (6) clamp cylinder (7) product... [Pg.115]

In the pure metal stamp forming process, both mold halves are made from metal. In silicone stamp forming, one mold half is mostly made from elastic material (mostly the upper mold half). Table 1.11 shows a comparison between both processes concerning the most important features. [Pg.241]

Upper heated platen Upper mold half... [Pg.293]

Match the upper mold half with the lower and once again place the closed mold centered on the lower platen of the press. [Pg.298]

See other pages where Upper mold half is mentioned: [Pg.485]    [Pg.683]    [Pg.242]    [Pg.338]    [Pg.442]    [Pg.444]    [Pg.1271]    [Pg.594]    [Pg.114]    [Pg.121]    [Pg.121]    [Pg.133]    [Pg.135]    [Pg.244]    [Pg.246]    [Pg.268]    [Pg.291]    [Pg.292]    [Pg.293]    [Pg.300]    [Pg.1271]    [Pg.1272]   
See also in sourсe #XX -- [ Pg.54 , Pg.63 , Pg.89 ]



SEARCH



© 2024 chempedia.info