Unite conversion factors for

Section 7.1 gives examples illustrating the use of quantity calculus for converting the values of physical quantities between different units. The table in section 7.2 lists a variety of non-SI units used in chemistry, with the conversion factors to the corresponding SI units. Conversion factors for energy and energy-related units (wavenumber, frequency, temperature and molar energy), and for pressure units, are also presented in tables inside the back cover. 

Table 15 shows the unit conversion factors for five properties. 

Conversion factors for mercury manometer pressure units are calculated using die standard value for the acceleration of gravity and die density of mercury at die stated temperature. Additional digits are not justified because the definitions of the units do not take into account die compressibility of mercury or the change in density caused by the revised practical temperature scale, ITS-90. Similar comments also apply to water manometer pressure units. Conversion factors for conventional mercury and water manometer pressure units are based on ISO 31-3. 

Unit conversion factors for selected electric properties... 

Unit conversion factors for electric dipole-magnetic dipole polarizability... 

The system of atomic units was developed to simplify mathematical equations by setting many fundamental constants equal to 1. This is a means for theorists to save on pencil lead and thus possible errors. It also reduces the amount of computer time necessary to perform chemical computations, which can be considerable. The third advantage is that any changes in the measured values of physical constants do not affect the theoretical results. Some theorists work entirely in atomic units, but many researchers convert the theoretical results into more familiar unit systems. Table 2.1 gives some conversion factors for atomic units. 

Exact numbers, such as the stoichiometric coefficients in a chemical formula or reaction, and unit conversion factors, have an infinite number of significant figures. A mole of CaCb, for example, contains exactly two moles of chloride and one mole of calcium. In the equality... 

The conversion factors for other compound units not Hsted can easily be generated from numbers given in the alphabetical Hst by the substitution of the converted units eg, to find the conversion factor from Ib-ft/s to kg-m/s ... 

The dimensions of permeabiUty become clear after rearranging equation 1 to solve for P. The permeabiUty must have dimensions of quantity of permeant (either mass or molar) times thickness ia the numerator with area times a time iaterval times pressure ia the denomiaator. Table 1 contains conversion factors for several common unit sets with the permeant quantity ia molar units. The unit nmol/(m-s-GPa) is used hereia for the permeabiUty of small molecules because this unit is SI, which is preferred ia current technical encyclopedias, and it is only a factor of 2, different from the commercial permeabihty unit, (cc(STP)-mil)/(100 in. datm). The molar character is useful for oxygen permeation, which could ultimately involve a chemical reaction, or carbon dioxide permeation, which is often related to the pressure in a beverage botde. 

The water-vapor transmission rate (WVTR) is another descriptor of barrier polymers. Strictly, it is not a permeabihty coefficient. The dimensions are quantity times thickness in the numerator and area times a time interval in the denominator. These dimensions do not have a pressure dimension in the denominator as does the permeabihty. Common commercial units for WVTR are (gmil)/(100 in. d). Table 2 contains conversion factors for several common units for WVTR. This text uses the preferred nmol/(m-s). The WVTR describes the rate that water molecules move through a film when one side has a humid environment and the other side is dry. The WVTR is a strong function of temperature because both the water content of the air and the permeabihty are direcdy related to temperature. Eor the WVTR to be useful, the water-vapor pressure difference for the value must be reported. Both these facts are recognized by specifying the relative humidity and temperature for the WVTR value. This enables the user to calculate the water-vapor pressure difference. Eor example, the common conditions are 90% relative humidity (rh) at 37.8°C, which means the pressure difference is 5.89 kPa (44 mm Hg). 

Table 15. Conversion factors for frequently reported damage dose units...

Conversion of units from one system to another is simply carried out if the quantities are expressed in terms of the fundamental units of mass, length, time, temperature. Typical conversion factors for the British and metric systems are ... 

Integers and exact numbers In multiplication or division by an integer or an exact number, the uncertainty of the result is determined by the measured value. Some unit conversion factors are defined exactly, even though they are not whole numbers. For example, 1 in. is defined as exactly 2.54 cm and the 273.15 in the conversion between Celsius and Kelvin temperatures is exact so 100.000°C converts into 373.150 K. 

The more permeable component is called the fast gas, so it is the one enriched in the permeate stream. Permeabihly through polymers is the product of solubility and diffusivity. The diffusivity of a gas in a membrane is inversely proportional to its kinetic diameter, a value determined from zeolite cage exclusion data (see Table 20-26 after Breck, Zeolite Molecular Sieves, Wiley New York, 1974, p. 636). Tables 20-27, 20-28, and 20-29 provide units conversion factors useful for calculations related to gas-separation membrane systems. 

In Figure 8 the doses per unit radon concentration are plotted as a function of the measured ventilation rate. The NEA conversion factor for low and moderate ventilation (NEA,1983, table 2.10) is multiplied by the appropriate equilibrium factor. In the figure no influence of the ventilation rate on the doses is found. 

Appendix. Conversion Factors for Commonly Used Units Universal Constants... 

---