Uniform cycle

The Ziegler and Nichols closed-loop method requires forcing the loop to cycle uniformly under proportional control. The natural period of the cycle—the proportional controller contributes no phase shift to alter it—is used to set the optimum integral and derivative time constants. The optimum proportional band is set relative to the undamped proportional band P , which produced the uniform oscillation. Table 8-4 lists the tuning rules for a lag-dominant process. A uniform cycle can also be forced using on/off control to cycle the manipulated variable between two limits. The period of the cycle will be close to if the cycle is symmetrical the peak-to-peak amphtude of the controlled variable divided by the difference between the output limits A, is a measure of process gain at that period and is therefore related to for the proportional cycle ... 

A uniform cycle can also be forced by using on-off control to cycle the manipulated variable between two limits. The period of the cycle will be close to Tn if the cycle is symmetric the peak-to-peak ampli-... 

A uniform cycle for all assembly stations set by the pace of the station with the longest cycle time... 

Set uniform cycle times Bushing 2. Decrease plunger fonivard time... 

Owing to the cycHc nature of the TBRC operation, waste heat recovery from the off-gases is not practical and the SO2 content of the gas varies with the converter cycle. In order to supply a relatively uniform flow and strength SO2 gas to a sulfuric acid plant, a system has been installed at RonnskAr whereby the SO2 from fluctuating smelter gases is partially absorbed in water. During smelter gas intermption, SO2 is stripped with air and the concentrated gas deflvered to the acid plant. 

The characteristics of interior paints that require testing and analysis include hiding and appearance, package stabiHty, adhesion, spatter resistance, flow and leveling, color and sheen uniformity, touch-up, stain removal, burnish resistance, and block and print resistance. A popular test that assesses the wet abrasion resistance of an interior paint is to measure its scmb resistance. A mechanical device is used to scmb a paint film of a specified thickness with a standard bmsh and abrasive cleanser suspension. The number of scmb cycles (back and forth movements of the weighted bmsh) at various end points (first cut through, or 50% removal of the film) is then recorded. Scmb resistance usually holds steady or decreases slightly as PVC is increased, but drops quickly once the CPVC is exceeded in a paint formulation. 

ASTM D1175, Uniform Abrasion Method (5000 cycles). 

Because hospital loads are not uniform, certain assumptions were made by the manufacturers of sterilizers in arriving at recommended cycles. These recommendations include a safety factor, as well as allowance for heatup time. Exposure recommendations for various types of articles are available (12). 

Uniform depth of loading in dryers and furnaces handling particulate solids is essential to consistent operation, minimum heating cycles, or control of final moisture. After a tray has been loaded, the bed should be leveled to a uniform depth. Special preform devices, noodle extruders, pelletizers, etc., are employed occasionally for preparing pastes and filter cakes so that screen bottom trays can be used and the advantages of through circulation approached. 

If any solids present in small amounts are soluble in a hquid portion of the mix, it is well to add them as a solution, making provision to distribute the liquid uniformly throughout the mass. When a trace of solid material which is not soluble in any other ingredients is to be added, it may be expedient to add it as a solution in a neutral solvent, with provision to evaporate the solvent at the end of the mixing cycle. 

Batch Percolators The batch tank is not unlike a big nutsche filter it is a large circiilar or rectangiilar tank with a false bottom. The solids to be leached are dumped into the tank to a uniform depth. They are sprayed with solvent until their solute content is reduced to an economic minimum and are then excavated. Countercurrent flow of the solvent through a series of tanks is common, with fresh solvent entering the tank containing most nearly exhausted material. In a typical ore-dressing operation the tanks are 53 by 20 by 5.5 m (175 by 67 by 18 ft) and extract about 8200 Mg (9000 U.S. tons) of ore on a 13-day cycle. Some tanks operate under pressure, to contain volatile solvents or increase the percolation rate. A series of pressure tanks operating with countercurrent solvent flow is called a diffusion battery. 

Pressure leaf filters are used to separate much the same lands of slurries as are filter presses and are used much more extensively than filter presses for filter-aid filtrations. They should be seriously considered whenever uniformity of production permits long-time operation under essentially constant filtration conditions, when thorough washing with a minimum of hquor is desired, or when vapors or fumes make closed construction desirable. Under such conditions, if the filter medium does not require frequent changing, they may show a considerable advantage in cycle and labor economy over a filter press, which has a lower initial cost, and advantages of economy and flexibility over continuous vacuum filters, which have a higher first cost. 

---