Unidirectional

The algorithm contains five minimisation procedures which are performed the same way as in the method " i.e. by minimisation of the RMS between the measured unidirectional distribution and the corresponding theoretical distribution of die z-component of the intensity of the leakage field. The aim of the first minimisation is to find initial approximations of the depth d, of the crack in the left half of its cross-section, die depth d in its right half, its half-width a, and the parameter c. The second minimisation gives approximations of d, and d and better approximations of a and c based on estimation of d,= d, and d,= d,j. Improved approximations of d] and d4 are determined by the third minimisation while fixing new estimations of d dj, dj, and dj. Computed final values dj , d/, a and c , whieh are designated by a subscript c , are provided by the fourth minimisation, based on improved estimations of d, dj, dj, and d . The fifth minimisation computes final values d, , d, dj, d while the already computed dj , d/, a and c are fixed. 

Chemical properties of deposited monolayers have been studied in various ways. The degree of ionization of a substituted coumarin film deposited on quartz was determined as a function of the pH of a solution in contact with the film, from which comparison with Gouy-Chapman theory (see Section V-2) could be made [151]. Several studies have been made of the UV-induced polymerization of monolayers (as well as of multilayers) of diacetylene amphiphiles (see Refs. 168, 169). Excitation energy transfer has been observed in a mixed monolayer of donor and acceptor molecules in stearic acid [170]. Electrical properties have been of interest, particularly the possibility that a suitably asymmetric film might be a unidirectional conductor, that is, a rectifier (see Refs. 171, 172). Optical properties of interest include the ability to make planar optical waveguides of thick LB films [173, 174]. 

Each set of p orbitals has three distinct directions or three different angular momentum m-quantum numbers as discussed in Appendix G. Each set of d orbitals has five distinct directions or m-quantum numbers, etc s orbitals are unidirectional in that they are spherically symmetric, and have only m = 0. Note that the degeneracy of an orbital (21+1), which is the number of distinct spatial orientations or the number of m-values. 

Another product is made with strands produced by flakers, having dimensions of about 0.8 x 13 x 300 mm (0.030 x 0.5 x 12 in.). The strands are dried and then coated with isocyanate adhesives. The strands are formed into mats with unidirectional orientation and pressed in a steam-through press. The large panels are then sawn into dimension lumber sizes. 

Applying the same derivation as for unidirectional diffusion through a stagnant medium, the results turn out to be... 

This leads to rate equations with constant mass transfer coefficients, whereas the effect of net transport through the film is reflected separately in thej/gj and Y factors. For unidirectional mass transfer through a stagnant gas the rate equation becomes... 

Equimolar Counterdiffusion. Just as unidirectional diffusion through stagnant films represents the situation in an ideally simple gas absorption process, equimolar counterdiffusion prevails as another special case in ideal distillation columns. In this case, the total molar flows and are constant, and the mass balance is given by equation 35. As shown eadier, noj/g factors have to be included in the derivation and the height of the packing is... 

General Situation. Both unidirectional diffusion through stagnant media and equimolar diffusion are idealizations that ate usually violated in real processes. In gas absorption, slight solvent evaporation may provide some counterdiffusion, and in distillation counterdiffusion may not be equimolar for a number of reasons. This is especially tme for multicomponent operation. 

Hot Pressing. Hot pressing may be used either to consoHdate a powder that has poor compactabiHty at room temperature, or to combine compaction and sintering in one operation. The technique is essentially the same as described for unidirectional die compacting. The powder is heated by either heating the entire die assembly in a furnace or by induction heating. In most instances, a protective atmosphere must be suppHed. 

Composites. High molecular weight PPS can be combiaed with long (0.6 cm to continuous) fiber to produce advanced composite materials (131). Such materials having PPS as the polymer matrix have been developed by usiag a variety of reinforcements, including glass, carbon, and Kevlar fibers as mat, fabric, and unidirectional reinforcements. Thermoplastic composites based on PPS have found application ia the aircraft, aerospace, automotive, appliance, and recreation markets (see Composite materials, polymer-matrix). 

Inflated Diaphragm Method (ASTM D3886). This method is appHcable both to woven and knitted fabrics. The specimen is abraded by mbbing either unidirectionally or multidirectionally against an abradant having specified surface characteristics. The specimen is supported by an inflated mbber diaphragm under a constant pressure. Evaluation of abrasion resistance can be either by determination of the number of cycles required to wear through the center of the fabric completely or by visual examination of the specimens after a specified number of cycles. 

Fig. 1. A unidirectional lamina. The material axes are labeled 1 for the fiber direction and 2 for the direction transverse to the fibers.

Fig. 2. Three layers of unidirectional material stacked together to form a laminate.

Fig. 5. Interlaminar fracture toughness, for a number of thermosetting and thermoplastic composites (36,37). Open white bars represent glass-fiber composites shaded bars are for carbon fibers. The materials are A, polyester (unidirectional) B, vinyl ester (CSM = chopped strand mat) C, epoxy (R/BR1424) D, epoxy (T300/914) E, PPS F, PES and G, PEEK. To convert J/m to fdbf/in. multiply by 2100.

The stiffness of of a unidirectional lamina in the fiber direction is also given approximately by the rule of mixtures ... 

Thus the addition of the stiff carbon fibers has a very great effect in stiffening the epoxy matrix. Eor the commonly used fiber volume fraction of 0.6 the unidirectional carbon—epoxy lamina has a predicted extensional stiffness E = 145 GPa (2.1 x 10 psi)-... 

---