Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

True alkali metals

One may rationalize emulsion type in terms of interfacial tensions. Bancroft [20] and later Clowes [21] proposed that the interfacial film of emulsion-stabilizing surfactant be regarded as duplex in nature, so that an inner and an outer interfacial tension could be discussed. On this basis, the type of emulsion formed (W/O vs. O/W) should be such that the inner surface is the one of higher surface tension. Thus sodium and other alkali metal soaps tend to stabilize O/W emulsions, and the explanation would be that, being more water- than oil-soluble, the film-water interfacial tension should be lower than the film-oil one. Conversely, with the relatively more oil-soluble metal soaps, the reverse should be true, and they should stabilize W/O emulsions, as in fact they do. An alternative statement, known as Bancroft s rule, is that the external phase will be that in which the emulsifying agent is the more soluble [20]. A related approach is discussed in Section XIV-5. [Pg.504]

Hydrides — True hydrides (i.e., those in which the hydrogen is in its anionic or most reduced form) are salt-like compounds in which the hydrogen is combined with alkali metals, either alone as simple hydrides or in association with other elements as complex hydrides. Hydrides react with water to release hydrogen. [Pg.174]

The true, all-aromatic system (see 18, below) described by Kime and Norymberski is unusual in the sense that all of the ether linkages bridge aromatic carbons ". Synthesis of 18, therefore, required extensive use of copper mediated coupling reactions. As expected for such reactions, yields were generally low. The aromatics such as 18 were ineffective at binding either alkali metal or ammonium cations ". ... [Pg.44]

Although the elements tantalum and niobium were discovered more than 200 years ago in the form of oxides, the true beginning of the chemistry of tantalum and niobium was the discovery and investigation of complex fluorotantalates and fluoroniobates of alkali metals. Application of complex fluoride compounds enabled the separation of tantalum and niobium and in fact initiated the development of the industrial production of the metals and their compounds. [Pg.398]

Intermetallic compounds are generally prepared by simply heating the elements in the correct molar proportion at or just below the liquidus temperature specified in the phase diagram. The major experimental problems associated with these methods are first, attack of the container material by the alkali metal or the intermetallic compound in the molten state second, the temperature chosen must be such as to attain true homogeneity of the intermetallic compound. [Pg.413]

Experimental data show that at the usual concentrations (10 to lOM), most salts and also the hydroxides of alkali metals are strong electrolytes. This is true also for some inorganic acids HCl, HCIO4, and others. Weak electrolytes are the organic acids and the hydroxides of metals other than alkah. Few electrolytes of the intermediate type (with moderate values of a) exist in particular, certain transition-metal halides such as ZnClj, Znl2, and CdCl2 are in this category. [Pg.105]

Copper oxides give rise to numerous accidents. When copper (II) oxide was heated with boron, it gave a highly violent reaction, which caused the melting of the Pyrex container. This is true for alkali metals and titanium as well as aluminium. The reactions lead to liquid metal copper. The emissions of glowing compounds make the reaction very dangerous. [Pg.207]

The quantity dyl3 In a2 at the potential of the electrocapillary maximum is of basic importance. As the surface charge of the electrode is here equal to zero, the electrostatic effect of the electrode on the ions ceases. Thus, if no specific ion adsorption occurs, this differential quotient is equal to zero and no surface excess of ions is formed at the electrode. This is especially true for ions of the alkali metals and alkaline earths and, of the anions, fluoride at low concentrations and hydroxide. Sulphate, nitrate and perchlorate ions are very weakly surface active. The remaining ions decrease the surface tension at the maximum on the electrocapillary curve to a greater or lesser degree. [Pg.222]

Summarizing all that has been said above concerning the structures of the octachloroditechnetates ( + 2.5), it may be concluded that their true composition is described by a formula with variable coefficients, namely M 6M"3-.,t(H30) [[Tc3Cl8] nH20, where x and n vary from 0 to 3. The substitution of some of the M ions by H30+ ions is possible by virtue of the similarity of the properties of the hydroxonium cation and the alkali metal cations both in solution and in the crystalline state [85,86],... [Pg.196]

Chemical Incompatibility Hazards While N2 and C02 may act as inerts with respect to many combustion reactions, they are far from being chemically inert. Only the noble gases (eg., Ar and He) can, for practical purposes, be regarded as true inerts. Frank (Frank, Inerting for Explosion Prevention, Proceedings of the 38th Annual Loss Prevention Symposium, AIChE, 2004) lists a number of incompatibilities for N2, C02, and CO (which can be present in gas streams from combustion-based inert gas generators). Notable incompatibilities for N2 are lithium metal and titanium metal (which is reported to burn in N2). C02 is incompatible with many metals (eg., aluminum and the alkali metals), bases, and amines, and it forms carbonic acid in water,... [Pg.37]

The Mechanism of the Ethyl Acetoacetate Synthesis—Before the tautomerism of ethyl acetoacetate is discussed we must consider the mechanism of its formation, which for decades has been the subject of lively discussion and was conclusively explained only in recent years (Scheibler). It has been found that even the C=0-group of the simple carboxylic esters, although in other respects inferior in activity to the true carbonyl group, can be enolised by alkali metals. Thus ethyl acetate is converted by potassium into the potassium salt of the tautomeric enol with evolution of hydrogen ... [Pg.258]

Occurrence. Thallium can be associated to heavy metals that occur in sulphidic ores (chalcophilic element behaviour) or to alkali metals in minerals such as car-nallite, sylvite, mica (the Tl+1 ion behaves as an alkali metal ion), or in true, but very rare, thallium minerals such as lorandite (T1AsS2), chalcothallite (Cu3T1S2). [Pg.482]

If we take a series of alkali metal halides, all with the rock salt structure, as we replace one metal ion with another, say sodium with potassium, we would expect the metal-halide internuclear distance to change by the same amount each time if the concept of an ion as a hard sphere with a particular radius holds true. Table 1.8 presents the results of this procedure for a range of alkali halides, and the change in internuclear distance on swapping one ion for another is highlighted. [Pg.53]

The activation energy for desorption comprises the heat of adsorption and the activation energy of adsorption, (see Fig. 1), but, as the adsorption of alkali metals and most gases on clean metal surfaces is non-activated, the activation energy of desorption is, in fact, equal to that of adsorption. Two classes of measurements have been made (1) those in which desorption occurred without subsequent readsorption, and (2) those where equilibrium conditions were approached during the desorption process. A true desorption velocity is observed in the first case only. [Pg.111]


See other pages where True alkali metals is mentioned: [Pg.156]    [Pg.156]    [Pg.125]    [Pg.56]    [Pg.53]    [Pg.290]    [Pg.424]    [Pg.735]    [Pg.300]    [Pg.24]    [Pg.288]    [Pg.28]    [Pg.75]    [Pg.109]    [Pg.320]    [Pg.359]    [Pg.77]    [Pg.64]    [Pg.87]    [Pg.245]    [Pg.152]    [Pg.661]    [Pg.392]    [Pg.399]    [Pg.125]    [Pg.519]    [Pg.286]    [Pg.160]    [Pg.36]    [Pg.27]    [Pg.345]    [Pg.137]    [Pg.62]    [Pg.48]   
See also in sourсe #XX -- [ Pg.156 ]




SEARCH



True

© 2024 chempedia.info