1,2,4-Triol, preparation

Poly (ester-urethane) Crosslinking of polyester triols prepared from D.L-lactide, c-caprolactone, or comonomer mixtures with ethyl 2,6-diisocyanatohexanoate. Chemical hydrolysis of polymer backbone. Storey et al, 1994... 

Diester/Ether Diol of Tetrabromophthalic Anhydride. This material [77098-07-8] is prepared from TBPA in a two-step reaction. First TBPA reacts with diethylene glycol to produce an acid ester. The acid ester and propylene oxide then react to give a diester. The final product, a triol having two primary and one secondary hydroxyl group, is used exclusively as a flame retardant for rigid polyurethane foam (53,54). 

Polyethers prepared from propylene oxide are soluble in most organic solvents. The products with the highest hydroxyl number (lowest molecular weight) are soluble in water, not in nonpolar solvents such as hexane. The solubihty of 3000 molecular weight triols is high enough in solvents such as toluene, hexane, and methylene chloride that the triols can be purified by a solvent extraction process. 

D,L-Arahinitol can be prepared by the action of hydrogen peroxide in the presence of formic acid on divinyl carbinol (36) and, together with ribitol (Fig. ld),fromD,L-erythron-4-pentyne-l,2,3-triol,HOCH2CHOHCHOHC=CH (37). 

Acetonide formation is the most commonly used protection for 1,2- and 1,3-diols. The acetonide has been used extensively in carbohydrate chemistiy to mask selectively the hydroxyls of the many different sugars. In preparing acetonides of triols, the 1,2-derivative is generally favored over the 1,3-derivative, but the extent to which the 1,2-acetonide is favored is dependent on stmcture. Note that the 1,2-selectivity for the ketal from 3-pentanone is better than that from acetone. ... 

A benzylidene acetal is a commonly used protective group for 1,2- and 1,3-diols. In the case of a 1,2,3-triol the 1,3-acetal is the preferred product. It has the advantage that it can be removed under neutral conditions by hydrogenolysis or by acid hydrolysis. Benzyl groups and isolated olefins have been hydrogenated in the presence of 1,3-benzylidene acetals. Benzylidene acetals of 1,2-diols are more susceptible to hydrogenolysis than are those of 1,3-diols. In fact, the former can be removed in the presence of the latter. A polymer-bound benzylidene acetal has also been prepared." ... 

One variation in polyester intermediates that has roused some interest are those prepared by a ring-opening polymerisation of e-caprolactone and methyl-e-caprolactones with titanium catalysts and diol and triol initiators Figure 27.6). 

Preparation—Cholestane-3(i,5a,6P-triol 3-Cathylate A solution of choles-tane-3/ ,5a,6j5-triol (1 g) in dioxane (10 ml) and pyridine (1.6 ml) is cooled to 25° and treated dropwise and with cooling with 2 ml of ethyl chlorocarbonate. After 1 hr, 25 ml of water and 1 ml of 36 % hydrochloric acid are added and the mixture is heated for 30 min on the steam bath and cooled. The product, a granular white solid, is filtered to yield 1.19 g mp 180-182°. Crystallization from methanol (75 ml) gives 0.62 g or prisms, mp 184.5-185°, and a second crop, 0.38 g, mp 183-184° (total yield 83%). Two recrystallizations of the 1st crop material yield prisms mp 184-185° [ ] —16° (CHCI3). 

Oxidation with lead tetraacetate, 243 preparation of 3/3-hydroxy-18-methyl-androst-4-en-17-one from 18-methyl-pregn-4-ene-3/3,17o ,20-triol, 243... 

An ethereal solution approximately 2.5 molar in methyllithium is prepared from 17 ml of methyl iodide and 4 g of lithium metal in 200 ml of anhydrous ether. A mixture consisting of 150 ml anhydrous ether, 3 g (10 mmoles) of 3jS-hydroxy-5a-androstane-ll,17-dione and 60 ml (0.15 moles) of the above methyllithium solution are stirred at room temperature for 40 hr. The reaction mixture is diluted with 100 ml of water and the ether is removed by distillation. Filtration of the chilled aqueous phase yields 2.6 g (77%) of 1 la,17a-dimethyl-5a-androstane-3a,l l/ ,17j5-triol mp 149-154°. Recrystallization from acetone-hexane yields pure material mp 164-166° [a] —5° (CHCI3). 

Many of the reactions already discussed for the preparation of bis-oxygenated pregnanes can also be used for the synthesis of 17,20,21-tris-oxygenated pregnanes by proper choice of substrate. Thus, reaction of a 17-vinyl-17-hydroxy steroid or a A -21-hydroxypregnene with osmium tetroxide will give the 17,20,21-triol, and the Stork reaction can be applied to 17a-hydroxy-20-keto steroids. 

Diborane reduction of an ortho ester that is prepared from a triol with CH3C(OEt)3, PPTS. ... 

This is one of the few methods available for the direct and efficient conversion of an acid, via the acid chloride, to an ortho ester. The preparation of the oxetane is straightforward, and a large number of oxetanes have been prepared [triol, (EtO)2CO, KOH]." In addition, the -butyl analogue has been used for the protection of acids. During the course of a borane reduction, the ortho ester was reduced to form a ketal. This was attributed to an intramolecular delivery of the hydride. ... 

To overcome these problems with the first generation Brmsted acid-assisted chiral Lewis acid 7, Yamamoto and coworkers developed in 1996 a second-generation catalyst 8 containing the 3,5-bis-(trifluoromethyl)phenylboronic acid moiety [10b,d] (Scheme 1.15, 1.16, Table 1.4, 1.5). The catalyst was prepared from a chiral triol containing a chiral binaphthol moiety and 3,5-bis-(trifluoromethyl)phenylboronic acid, with removal of water. This is a practical Diels-Alder catalyst, effective in catalyzing the reaction not only of a-substituted a,/ -unsaturated aldehydes, but also of a-unsubstituted a,/ -unsaturated aldehydes. In each reaction, the adducts were formed in high yields and with excellent enantioselectivity. It also promotes the reaction with less reactive dienophiles such as crotonaldehyde. Less reactive dienes such as isoprene and cyclohexadiene can, moreover, also be successfully employed in reactions with bromoacrolein, methacrolein, and acrolein dienophiles. The chiral ligand was readily recovered (>90%). 

The top layer was washed with water and ethylene glycol and dried to give 135 g of a yellow oily material that from infrared spectral analysis was identified to be the same triol used to prepare the flexible polyurethane foam. 

Because the condensation between a diketene acetal and a diol proceeds without the evolution of volatile byproducts, this method allows the preparation of dense, crossUnked materials by using reagents having a functionality greater than 2 (15). Even though either or both the ketene acetal and alcohol could have functionalities greater than 2, only triols were investigated because the synthesis of trifunctional ketene acetals is extremely difficult. 

To prepare crosslinked material, 2 eq of the diketene acetal is reacted with 1 eq of the diol and the resulting prepolymer is then reacted with a triol or a mixture of diols and triols. 

FIGURE 18 In vivo cumulative weight loss (o) and cumulative release of levonorgestrel (o) from a crossUnked polymer prepared from a 3,9-bis(ethylidene-2,4,8,10-tetraoxaspiro[5,5]undecane)/3-methyl-1,5-pentanediol prepolymer crossUnked with 1,2,6-hexane triol. Polymer rods, 2.4 X 20 mm, containing 30 wt% levonorgestrel and 7.1 mol% Mg(OH)2. Devices implanted subcutaneously in rabbits. (From Ref. 15.)... 

Me, m-OMe, m-Cl, m-CF3, etc.) have been prepared by hydrolysis of the corresponding X-C6H4Si(OMe)3 compounds in an H20/MeOH mixture. Again, the formation of an alcohol, MeOH, rather than a hydrogen halide is beneficial in the synthesis of such sensitive triols (102). 

Recently, catalytic asymmetric Diels-Alder reactions have been investigated. Yamamoto reported a Bronsted-acid-assistcd chiral (BLA) Lewis acid, prepared from (R)-3-(2-hydroxy-3-phcnylphenyl)-2,2 -dihydroxy-1,1 -binaphthyl and 3,5A(trifluoromethy I) - be nzeneboronic acid, that is effective in catalyzing the enantioselective Diels-Alder reaction between a,(3-enals and various dienes.62 The interesting aspect is the role of water, THF, and MS 4A in the preparation of the catalyst (Eq. 12.19). To prevent the trimerization of the boronic acid during the preparation of the catalyst, the chiral triol and the boronic acid were mixed under aqueous conditions and then dried. Using the catalyst prepared in this manner, a 99% ee was obtained in the Diels-Alder reaction... 

Following the convergent procedure, dendrimers of type 58,59 and 60 have been prepared from the chiral core triol 54 and achiral Frechet-type [62] ben-zylic branch bromides. In the series of dendrimers with aromatic spacers (60) and without spacers (58), the optical activity [a]D decreased on going from the 1st (not shown in Fig. 21) to the 2nd generation, whereas with aliphatic spacers... 

Oxidation of 1-boraadamantane THF complex 42 with H2O2 in basic media <1979IZV2544> or by trimethylamine iV-oxide dihydrate <2003JA12179, 20010L3063> gave rise to the triol, m, r-l,3,5-tris(hydroxymethyl)cyclohexane 43. The triol 44 was also prepared from the adduct 45 using the first procedure (Scheme 11) <1979IZV2724>. 

Figure 11. Mooney-Rivlin plot of stress-strain data (32) for three triol-based polyester networks prepared from sebacoyl chloride and LHT240 at various initial dilutions in diglyme as solvent. Conditions P100 is 0% solvent P130 is 30% solvent PI 65 is 65% solvent.

Polyurethane networks were prepared from polyoxypropylene (POP) triols(Union Carbide Niax Polyols) after removal of water by azeotropic distillation with benzene. For Niax LHT 240, the number-average molecular weight determined by VPO was 710 and the number-average functionality fn, calculated from Mjj and the content of OH groupSj determined by using excess phenyl isocyanate and titration of unreacted phenyl isocyanate with dibutylamine, was 2.78 the content of residual water was 0.02 wt.-%. For the Niax LG-56, 1 =2630, fn=2.78, and the content of H2O was 0.02wt.-%. The triols were reacted with recrystallized 4,4"-diphenylmethane diisocyanate in the presence of 0.002 wt.-% dibutyltin dilaurate under exclusion of moisture at 80 C for 7 days. The molar ratio r0H = [OH]/ [NCO] varied between 1.0 and 1.8. For dry samples, the stress-strain dependences were measured at 60 C in nitrogen atmosphere. The relaxation was sufficiently fast and no extrapolation to infinite time was necessary. 

The equilibrium shear modulus of two similar polyurethane elastomers is shown to depend on both the concentration of elastically active chains, vc, and topological interactions between such chains (trapped entanglements). The elastomers were carefully prepared in different ways from the same amounts of toluene-2,4-diisocyanate, a polypropylene oxide) (PPO) triol, a dihydroxy-terminated PPO, and a monohydroxy PPO in small amount. Provided the network junctions do not fluctuate significantly, the modulus of both elastomers can be expressed as c( 1 + ve/vc)RT, the average value of vth>c being 0.61. The quantity vc equals TeG ax/RT, where TeG ax is the contribution of the topological interactions to the modulus. Both vc and Te were calculated from the sol fraction and the initial formulation. Discussed briefly is the dependence of the ultimate tensile properties on extension rate. 

Studies have been made of the elastic (time-independent) properties of single-phase polyurethane elastomers, including those prepared from a diisocyanate, a triol, and a diol, such as dihydroxy-terminated poly (propylene oxide) (1,2), and also from dihydroxy-terminated polymers and a triisocyanate (3,4,5). In this paper, equilibrium stress-strain data for three polyurethane elastomers, carefully prepared and studied some years ago (6), are presented along with their shear moduli. For two of these elastomers, primarily, consideration is given to the contributions to the modulus of elastically active chains and topological interactions between such chains. Toward this end, the concentration of active chains, vc, is calculated from the sol fraction and the initial formulation which consisted of a diisocyanate, a triol, a dihydroxy-terminated polyether, and a small amount of monohydroxy polyether. As all active junctions are trifunctional, their concentration always... 

Elastomers Prepared. The three elastomers discussed herein were prepared from PPG, toluene-2,4-diisocyanate (TDI), and either LHT-240 or TIPA. Elastomers prepared by a one-step procedure are designated LHT-240 and TIPA, indicative of the triol used. A third elastomer, designated Tri-NCO, was prepared by first reacting LHT-240 with all of the required TDI for two hours at 50°C to obtain a triisocyanate (or essentially... 

---