TLV—

Li and Neumann sought an equation of state of interfacial tensions of the form 7 l = /(Tlv. TSv). Based on a series of measurements of contact angles on polymeric surfaces, they revised an older empirical law (see Refs. 216, 217) to produce a numerically robust expression [129, 218]... 

Exposure limits (threshold limit value or TLV) are those set by the Occupational Safety and Health Administration and represent conditions to which most workers can be exposed without adverse effects. The TLV value is expressed as a time weighted average airborne concentration over a normal 8-hour workday and 40-hour workweek. 

TABLE 11.49 TLV Concentration Limits for Gases and Vapors Continued)... 

Material Safety Data Sheets (MSDS) issued by suppHers of acetone ate requited to be revised within 90 days to include new permissible exposure limits (PEL). Current OSHA PEL (54) and ACGIH threshold limit values (TLV) (55) ate the same, 750 ppm TWA and 1000 ppm STEL. Eot comparison, the ACGIH TWA values for the common mbbing alcohols are ethyl, 1000, and isopropyl, 400 ppm. A report on human experience (56) concluded that exposure to 1000 ppm for an 8-h day produced no effects other than slight, transient irritation of the eyes, nose, and throat. 

Current TLV/TWA values are provided in Matena/Safety Data Sheets provided by manufacturers upon request. Values for 1989 (83,107) appear in Table 5. 

Monomer Acute oral LD q, rats, mg/kg Acute precutaneous LD q, rabbits, mg/kg Inhalation LC q, rats, mg/L TLV, ppm... 

The 2-cyanoacryhc esters have sharp, pungent odors and are lacrimators, even at very low concentrations. These esters can be irritating to the nose and throat at concentrations as low as 3 ppm eye irritation is observed at levels of 5 ppm (13). The TLV for methyl 2-cyanoacrylate is 2 ppm and the short-term exposure limit is 4 ppm (14). Good ventilation when using the adhesives is essential. 

Exposure limits for siHcon carbide and powders of zirconium compounds (including zirconium dioxide) have been estabHshed by ACGIH. TLV—TWA s are 10 mg/m and 5 mg/m, respectively. OSHA guidelines for zirconium compounds call for a PEL of 5 mg/m. There are no exposure limits for siHcon nitride powder, but pmdent practice suggests a TLV—TWA of 0.1 mg/m. The soHd ceramics present no apparent health hazard. In machining such ceramics, however, care should be taken to prevent inhalation of respirable particles in amounts in excess of estabHshed limits. Disposal should be in approved landfills the materials are inert and should pose no danger to the environment. 

Because EPA was so slow in promulgating standards for HAPs prior to the 1990 Amendments, most states developed and implemented their own TAP control programs. Such programs, as well as the pollutants they regulate, differ widely from state to state. The ambient standards for a given substance are usually selected to be some small fraction of the TLV for that substance. 

The OSHA permissible exposure limit (11) and the American Conference of Governmental Industrial Hygienists (ACGIH) estabHshed threshold limit value (TLV) (12) for fluorides is 2.5 mg of fluoride per cubic meter of air. This is the TLV—TWA concentration for a normal 8-h work day and a 40-h work week. 

The toxicity of these fluoroaluminates is mainly as inorganic fluorides. The ACGIH adopted (1992—1993) values for fluorides as F is TLV 2.5 mg/m. The oral toxicity in laboratory animal tests is reported to be LD q rat 2.15 mg/kg (41). Because of the fine nature of the products they can also be sources of chronic toxicity effects as dusts. 

Health and Safety Factors. Boron trifluoride is primarily a pulmonary irritant. The toxicity of the gas to humans has not been reported (58), but laboratory tests on animals gave results ranging from an increased pneumonitis to death. The TLV is 1 ppm (59,60). Inhalation toxicity studies in rats have shown that exposure to BF at 17 mg/m resulted in renal toxicity, whereas exposure at 6 mg/m did not result in a toxic response (61). Prolonged inhalation produced dental fluorosis (62). High concentrations bum the skin similarly to acids such as HBF and, if the skin is subject to prolonged exposure, the treatment should be the same as for fluoride exposure and hypocalcemia. No chronic effects have been observed in workers exposed to small quantities of the gas at frequent intervals over a period of years. 

The ACGIH adopted TLV/TWA for 1992—1993 for fluorides as F is TWA 2.5 mg/m, and for cobalt as Co metal dust TWA 0.05 mg/m. Dust masks should be used while handling both the cobalt fluorides and all other cobalt compounds. CoF is shipped as an oxidizer and a corrosive material. 

Mild exposure to HF via inhalation can irritate the nose, throat, and respiratory system. The onset of symptoms may be delayed for several hours. Severe exposure via inhalation can cause nose and throat bums, lung inflammation, and pulmonary edema, and can also result in other systemic effects including hypocalcemia (depletion of body calcium levels), which if not promptly treated can be fatal. Permissible air concentrations are (42) OSHA PEL, 3 ppm (2.0 mg/m ) as E OSHA STEL, 6 ppm (5.2 mg/m ) as E and ACGIH TLV, 3 ppm (2.6 mg/m ) as E. Ingestion can cause severe mouth, throat, and stomach bums, and maybe fatal. Hypocalcemia is possible even if exposure consists of small amounts or dilute solutions of HE. 

Mercury salts are highly toxic and must be handled carefliUy. It is necessary to consult the material safety data sheet prior to handling. Strict adherence to OSHA/EPA regulations is essential. The ACGIH adopted (1991—1992) TLV for mercury as inorganic compounds is TWA 0.1 mg/m and for fluorides as F 2.5 mg/m. ... 

Toxicology and Handling. The lethal dose by ingestion in guinea pigs is 150 mg/kg body weight (13). The TLV for KHF2 is 2.5 mg /m ... 

Stannous fluoride is used in dentifrices and dental preparations. The OSHA permissible exposure limit (44) and ACGIH (45) estabUshed TLV for fluoride is 2.5 mg/m of air. 

---