Thermal cracking production

Products from catalytic cracking units are also more stable due to a lower olefin content in the liquid products. This reflects a higher hydrogen transfer activity, which leads to more saturated hydrocarbons than in thermally cracked products from delayed coking units, for example. 

Before considering the reactions of individual hydrocarbons it is worthwhile to review the general cracking behavior of the hydrocarbon classes. Table I shows a comparison of catalytic and thermal cracking products (Greensfelder, Voge, and Good, 1) ... 

Chains play an important part in all the mechanisms proposed for the acetylene production from methane in electric discharge. The composition of electrocracking products of various organic vapour in silent discharge resembles that of thermal cracking products (pyrolysis) of the same compounds. As the nature of active centers in these reactions is different, resembling product compositions would be expected only if the main amounts of these are generated by secondary processes this is only possible with chain mechanisms. 

Olefins are produced primarily by thermal cracking of a hydrocarbon feedstock which takes place at low residence time in the presence of steam in the tubes of a furnace. In the United States, natural gas Hquids derived from natural gas processing, primarily ethane [74-84-0] and propane [74-98-6] have been the dominant feedstock for olefins plants, accounting for about 50 to 70% of ethylene production. Most of the remainder has been based on cracking naphtha or gas oil hydrocarbon streams which are derived from cmde oil. Naphtha is a hydrocarbon fraction boiling between 40 and 170°C, whereas the gas oil fraction bods between about 310 and 490°C. These feedstocks, which have been used primarily by producers with refinery affiliations, account for most of the remainder of olefins production. In addition a substantial amount of propylene and a small amount of ethylene ate recovered from waste gases produced in petroleum refineries. 

Thermal Cracking. In addition to the gases obtained by distillation of cmde petroleum, further highly volatile products result from the subsequent processing of naphtha and middle distillate to produce gasoline, as well as from hydrodesulfurization processes involving treatment of naphthas, distillates, and residual fuels (5,61), and from the coking or similar thermal treatment of vacuum gas oils and residual fuel oils (5). 

As indicated in Table 4, large-scale recovery of natural gas Hquid (NGL) occurs in relatively few countries. This recovery is almost always associated with the production of ethylene (qv) by thermal cracking. Some propane also is used for cracking, but most of it is used as LPG, which usually contains butanes as well. Propane and ethane also are produced in significant amounts as by-products, along with methane, in various refinery processes, eg, catalytic cracking, cmde distillation, etc (see Petroleum). They either are burned as refinery fuel or are processed to produce LPG and/or cracking feedstock for ethylene production. 

The most important commercial use of ethane and propane is in the production of ethylene (qv) by way of high temperature (ca 1000 K) thermal cracking. In the United States, ca 60% of the ethylene is produced by thermal cracking of ethane or ethane/propane mixtures. Large ethylene plants have been built in Saudi Arabia, Iran, and England based on ethane recovery from natural gas in these locations. Ethane cracking units have been installed in AustraHa, Qatar, Romania, and Erance, among others. 

Reactions of /l-Butane. The most important industrial reactions of / -butane are vapor-phase oxidation to form maleic anhydride (qv), thermal cracking to produce ethylene (qv), Hquid-phase oxidation to produce acetic acid (qv) and oxygenated by-products, and isomerization to form isobutane. 

Production of maleic anhydride by oxidation of / -butane represents one of butane s largest markets. Butane and LPG are also used as feedstocks for ethylene production by thermal cracking. A relatively new use for butane of growing importance is isomerization to isobutane, followed by dehydrogenation to isobutylene for use in MTBE synthesis. Smaller chemical uses include production of acetic acid and by-products. Methyl ethyl ketone (MEK) is the principal by-product, though small amounts of formic, propionic, and butyric acid are also produced. / -Butane is also used as a solvent in Hquid—Hquid extraction of heavy oils in a deasphalting process. 

Manufacture of Monomers. The monomers of the greatest interest are those produced by oligomerization of ethylene (qv) and propylene (qv). Some olefins are also available as by-products from refining of petroleum products or as the products of hydrocarbon (qv) thermal cracking. 

The main limitation to thermal conversion is that the products can be unstable. Thermal cracking at low pressure gives olefins, particularly in the naphtha fraction such olefins yield an unstable product that tends to form gum as well as heavier products that form sediments (5). 

Alternatively, thermal cracking of acetals or metal-catalyzed transvinylation can be employed. Vinyl acetate or MVE can be employed for transvinylation and several references illustrate the preparation especially of higher vinyl ethers by such laboratory techniques. Special catalysts and conditions are required for the synthesis of the phenol vinyl ethers to avoid resinous condensation products (6,7). Direct reaction of ethylene with alcohols has also been investigated (8). 

Thermal Asphalt. Thermal asphalt products are in low supply because the thermal process has been virtually replaced by catalytic cracking processes. Thermal pitches, because of their high viscosity temperature susceptibiHty, are very hard at ordinary temperatures (Table 9), but become quite... 

Thermal Cracking. Heavy petroleum fractions such as resid are thermally cracked in delayed cokers or flexicokers (44,56,57). The main products from the process are petroleum coke and off-gas which contain light olefins and butylenes. This stream also contains a considerable amount of butane. Process conditions for the flexicoker are more severe than for the delayed coker, about 550°C versus 450°C. Both are operated at low pressures, around 300—600 kPa (43—87 psi). Flexicokers produce much more linear butenes, particularly 2-butene, than delayed cokers and about half the amount of isobutylene (Table 7). This is attributed to high severity of operation for the flexicoker (43). 

---