The T-bag method

Cut two sheets of polypropylene mesh material of size large enough to fit all the T-bags needed for the multiple synthesis. 

Mark a raster of 3 cm X 4 cm rectangles on one sheet of the polypropylene mesh, using the cardboard template. 

Mark a number with the ink pen on the bottom of each rectangle. 

Put the unmarked sheet on top of the sheet with the ink-marked labels and seal the lines between all the rectangles (the very top line remains open—three sides of the bags have to be sealed). The number is permanently sealed into the polypropylene to ensure identification of each bag. 

Cut the sheet into strips to form pockets and fill each with 100 mg of resin. 

---

Iterative Deconvolution. The first iterative library was composed of 400 separate hexapeptide mixtures, in which the first two positions from the amino terminus contained single individual amino acids. Out of the 20 proteinogenic amino acids, 400 dipeptides were formed (AA, AC, and so on through YW, YY). The remaining four positions were mixtures of 19 amino acids (cysteine was excluded), so that each mixture was composed of 19" or 130,321 individual peptides. Thus, a total of400 x 130,321 (52,128,400) hexapeptides were synthesized. This library was prepared using the T-bag method in combination with split-and-pool synthesis. ... 

Vanhatalo, A., I. Aronen and T. Varvikko, 1995. Intestinal nitrogen digestibility of heat-moisture treated rapeseed meals as assessed by the mobile-bag method in cows. Anim. Feed Sci. Technol. 55, 139-152. 

Synthesis of combinatorial arrays of compounds can, in principle, be performed three different ways. The Split and Mix (split and pool/recombine) concept introduced by Furka (4-6) is the most efficient method for preparation of sizable libraries (tens of thousands of compounds). However, the technique requires tracking of the chemical history of the resin beads and limits the quantity of synthesized material to the loading per solid phase unit (one unit can be represented by one particle, bead, lantern, etc., or one container, T-bag, Kan, etc.). Parallel synthesis, on the other hand, can supply any quantity per compound, but it requires handling large numbers of reaction vessels at one time. 

Results of applying the CCSD(T) method to selected tin compounds are also given in Table 1. Again, there are almost no data available in the literature for comparison. However, the predicted heat of formation for SnO is in reasonable agreement with experiment. Since data for Sn - O species are so limited, it is difficult to fully validate this model chemistry. Thus, we placed relatively high uncertainties on the calculated values. Nevertheless, we are sufficiently confident of the results to use them to establish BAG parameters for Sn - OH bonds. The resulting BAC-MP4 predictions as well as the... 

The reagent BOP and the more recent reagents PyBOP, AOP, and PyAOP are widely used in solutionP P l and in sohd-phase synthesis with rnanual,P l automated, tea bag,t l or pint methods. One-pot or preactivation conditions as well... 

The pulp to be treated with cellulolytic enzymes should first be screened in a laboratory flat screen to remove any shives. The screened pulp is beaten either in a laboratory Hollander beater (TAPPI Standard Method T 200 os-70) or in a PFI mill (TAPPI Standard Method T 248cm-85), depending on the amount of pulp to be treated, to a final Canadian Standard Freeness of 200-300 ml. The beating operation helps convert shives into fibers and improves the digestibility of the pulp towards cellulolytic enzymes. The pulp is dewatered to a consistency of approximately 25% and stored in a polyethylene bag after fluffing. 

Drugs may require i.v. administration as continuous infusions or at intervals (q4h, q6h, ql2h, etc.). Manual methods require the administration of the drug into the i.v. system at an injection site (Y-site, T-connector, stopcock, etc.), added to the i.v. solution in a mixing chamber, or added to an i.v. bag to be administered via gravity. A syringe pump or another mechanical device may be used for drug administration. 

Husar( 1971) studied the coagulation of ultrahne particles produced by a propane torch aerosol in a 90-m polyethylene bag. The size distribution was measured as a function of time with an electrical mobility analyzer. The results of the experiments are shown in Fig. 7.11 in which the size distribution is plotted as a function of particle diameter and in Fig. 7.12 in which is shown as a function of t) both based on particle radius. Numerical calculations were carried out by a Monte Carlo method, and the results of the calculation are also shown in Fig. 7.12. The agreement between experi ment and the numerical calculations is quite satisfactory. 

A 0.40-g (17.4-mmol) sample of sodium hydride (NaH) is placed in a twonecked flask of 2S0-mL capacity with ground-glass or Teflon stopcocks. This is washed three (3) times with dry hexane in an evacuable glove-bag and stored under dry nitrogen. Hexane and tetrahydrofuran (THF) were distilled over sodium benzophenone and stored over Li[AlH4] under vacuum. The 1.7 M t-BuLi in pentane (Aldrich Chemical Co.) is used as received. The nido-2,3-((CH3)3Si)2-2,3-C2B4.H6 is prepared by the method described above. 

Figure 5 With the new die change method, die exchange was reduced to 1.5 min. New hardware /2 turn die clamps air bag die lifters in press bolster in-and-out ball transfer table for exchanging dies. Tool modifications standardize shut heights subplated die sets. Press modifications new boslter and ram plates with T slots. End result eliminated fork truck and additional personnel for die exchange average time for die clamp, unclamp, and die exchange in 3 Minutes.

The present experiments used a method based on the work of Mauron t al. (1955) and Steinhart and Kirchgessner (1973) and consisting of a two-step hydrolysis, using first pepsin in a closed system, and then pancreatin in a dialysis bag (Savoie et al.> 1980 Gauthier et al., 1982). 

---