Tanning imported

Fig. 10.20 presents the release of Ag from polyester/Ag (160 s) and polyester/ Ag-TaN (20 s). For the polyester/Ag samples up to the eighth cycle, the level of Ag release drops from 8 to about 4 ppb/cm, and for the Ag-TaN (20 s) sample, Ag release drops from 4 to about 1 ppb/cm. TaN sputtered on polyester will therefore improve the biocompatibUity level of Ag because the disinfection process occurs at a lower Ag release level. The TaN is known for its excellent biocompatibility, which makes Ag-TaN an important material in biorelated applications.This feature makes polyester—Ag-TaN important to biochemical applications in implants because of nitride TaN-proven biocompatibihty concomitant with observed accelerated bacterial... 

All compounds of chromium are colored the most important are the chromates of sodium and potassium and the dichromates and the potassium and ammonium chrome alums. The dichromates are used as oxidizing agents in quantitative analysis, also in tanning leather. 

For an air/glass interface, tan 0b = n, the refractive index of glass. In a gas laser, the light must be reflected back and forth between mirrors and through the gas container hundreds of times. Each time the beam passes through the cavity, it must pass through transparent windows at the ends of the gas container (Figure 18.10b), and it is clearly important that this transmission be as efficient as possible. 

Many procedures have been studied for detoxification of aflatoxkis, including heat and treatment with ammonia, methylamine, or sodium hydroxide coupled with extraction from an acetone—hexane—water solvent system. Because ki detoxification it is important to free the toxki from cellular constituents to which it is bound, a stabifi2ation of protekis uskig a tanning compound such as acetaldehyde (qv) or glutaraldehyde may be a solution to the problem (98). 

The chrome-tanned leather is removed from the dmm and wmng to remove the absorbed tanning solution. The leather is then inspected for quaUty of the grain and other characteristics of importance for the leather being made. In large tanneries where very uniform hides are worked, the leather may be trimmed and spHt to the desired thickness. Hides spHt before tanning need no splitting at this point. 

Chrome Tanning. The original chrome tanning was a two-bath process. The unhaired hides, delimed and bated, were treated with a solution of sodium bichromate [10588-01-9]. The amount of bichromate used was about 3—5% based on the weight of the hides. The bichromate was absorbed or adsorbed into the hide, the solution drained, and the hides refloated. Sodium bisulfite was added and two important reactions resulted in the formation of a basic chromium and coUoidal sulfur in the hide. This gave a chrome taimage and also helped to fiH the hide with the soHd sulfur. This cmde system, which continued in the industry in some types of leather for over 50 years, is obsolete. 

Naphthalene derivatives are of diverse importance as intermediates for agricultural, constmction, pharmaceutical, photographic, mbber, tanning, and textile chemicals. In this article production figures, economics, and processes are discussed for most commercially important compounds. Sources for a more comprehensive study of naphthalene derivatives are available (1 8). 

Naphthalenesulfonic Acid—Formaldehyde Condensates. The sodium salts of the condensation products of naphthalenesulfonic acid with formaldehyde constitute an important class of compounds which are mainly used in the area of concrete additives (32,33), agricultural formulations, mbber formulations, and synthetic tanning agents. They are also used in photographic materials (34). Hampshire Chemical Co. and Henkel of America, Inc., are the largest suppHers of naphthalene sulfonate in concrete additives (superplasticizer) and reportedly hold 75—80% of this market. It was estimated that naphthalene sulfonate demand from U.S. producers would reach approximately... 

Hydroxynaphthalenesulfonic acids are important as intermediates either for coupling components for a2o dyes or a2o components, as well as for synthetic tanning agents. Hydroxynaphthalenesulfonic acids can be manufactured either by sulfonation of naphthols or hydroxynaphthalenesulfonic acids, by acid hydrolysis of arninonaphthalenesulfonic acids, by fusion of sodium naphthalenepolysulfonates with sodium hydroxide, or by desulfonation or rearrangement of hydroxynaphthalenesulfonic acids (Table 6). 

Leather Tanning and Textiles. Although chromium (VT) compounds are the most important commercially, the bulk of the appHcations in the textile and tanning industries depend on the abiUty of Cr(III) to form stable complexes with proteins, ceUulosic materials, dyestuffs, and various synthetic polymers. The chemistry is complex and not well understood in many cases, but a common denominator is the coordinating abiUty of chromium (ITT) (see LEATHER Textiles). 

The chrome tanning is one step in a compHcated series of leather operations leading from the raw hide to the finished products. Chrome tanning is the most important tannage for all hides except heavy catde hides, which are usually vegetable tanned. In heavy shoe uppers and soles, a chrome tanned leather is frequently given a vegetable retan to produce chrome retan leather. 

The models of Matranga, Myers and Glandt [22] and Tan and Gubbins [23] for supercritical methane adsorption on carbon using a slit shaped pore have shown the importance of pore width on adsorbate density. An estimate of the pore width distribution has been recognized as a valuable tool in evaluating adsorbents. Several methods have been reported for obtaining pore size distributions, (PSDs), some of which are discussed below. 

Sulfur in crude oils is mainly present in the form of organosulfur compounds. Hydrogen sulfide is the only important inorganic sulfur compound found in crude oil. Its presence, however, is harmful because of its corrosive nature. Organosulfur compounds may generally be classified as acidic and non-acidic. Acidic sulfur compounds are the thiols (mercap-tans). Thiophene, sulfides, and disulfides are examples of non-acidic sulfur compounds found in crude fractions. Extensive research has been carried out to identify some sulfur compounds in a narrow light petroleum fraction.Examples of some sulfur compounds from the two types are ... 

Total acid number (TAN) is a measure of the amount of acid or acid-like material in the oil sample. Because new oils contain additives that affect the TAN number, it is important to compare used oil samples with new, unused, oil of the same type. Regular analysis at specific intervals is important to this evaluation. 

In the context of this section it is important that Ruchardt and Tan (1970 a) found that (solid) benzenediazonium fluoroborate gave benzyne adducts with potassium acetate in the presence of aryne trapping agents such as tetracyclone or anthracene. This is, however, not the case if water is present (Cadogan, 1971). As a consequence of these observations, Cadogan et al. (1971) simplified the formation of arynes from diazonium ions by converting aniline or its substitution products into arynes in a... 

---