Table legs

How to Use Cut a hole that corresponds in size and shape to a cross-section of each table leg through the center of an aluminum pie plate. Invert the cut pans and slide 1 up each table leg. Fold each pan downward to form a cup and cover the inside of the cupped plate with sticky coating. Seal the crack between the pie plate and the table leg with caulking or sticky coating. Renew the sticky coating when necessary. Leave the traps in place permanently to guard against ants. 

Inserts bolts into table legs using pin machine pushes table leg against rotating drill Cements precut laminated plastic covering to plywood panels for desktops, countertops, etc. Uses solvent to remove excess cement... 

Four 2" X 2" table legs, cut to desired table height... 

Figure 61 The first step in assembling the platen table is to slide the table legs onto the stationary posts.

Figure 59 Platen table legs. Make 4 from 1 square x 11 gauge wall square tubing.

Cut four, 8 lengths of 1 square x 11 gauge wall steel square tubing for the platen table legs. See figure 59. 

A variability risk table (as shown in Figure 2.28 for the eover support leg analysis above) is a more elfieient and traeeable way of presenting the results of the first part of the analysis. A blank variability risks results table is provided in Appendix VII. It eatalogues all the important design information, sueh as the toleranee plaeed on the eharaeteristie, the eharaeteristie dimension itself, surfaee roughness value, and then allows the praetitioner to input the results determined from the variability risks analysis, both manufaeturing and assembly. 

Figure 2.28 Variability risks table for the cover support leg...

For example, the characteristic dimension A on the cover support leg was critical to the success of the automated assembly process, the potential failure mode being a major disruption to the production line. An FMEA Severity Rating (S) = 8 is allocated. See a Process FMEA Severity Ratings table as provided in Chrysler Corporation et al. (1995) for guidance on process orientated failures. The component cost, Pc = 5.93 and the number planned to be produced per annum, N = 50000. 

Valve thickness 16 gage (0.060 in.), 4-legs Valve material carbon steel, see Table 8-24. 

Table 4-4 gives the calculations of the force in each leg of the derrick due to the centered load (i.e., 613,500 lb), the hoist-line load (i.e., the fast-line load ... 

The actual load on the derrick is the sum of the bottom row in Table 4-4. The equivalent load is four times the force in leg A, which is the largest load of all four legs. 

Whilst they will differ depending upon gas properties, the procedures and precautions appropriate for transport of cylinder gases are exemplified for LEG in Table 15.16. 

Calculation of material halances of the polystyrene latexes through these LEG systems showed significant retention of the sample within the column. Percent recoveries of polystyrene latexes calculated at 2 k nm for the columns oj Set II are given in Table IV. The small particle sizes (<1000 A) are completely recovered, while significant loss of sample is seen for the larger particle sizes. 

Whole-body dosimeters are processed post-exposure as follows. The whole-body dosimeter is laid on a table covered with fresh aluminum foil and is sectioned into various pieces using a solvent-cleaned pair of scissors. The whole-body dosimeter is usually cut just at the knees to provide two lower leg sections, at the waist to provide an upper leg section, at the elbow to provide two lower arm sections, at the edge of each shoulder to provide two upper arm sections, and across the shoulders and down each side of the chest area to provide a front torso and back torso sample. The two-dosimeter sections from symmetrical parts of the body are combined to form one sample and wrapped in aluminum foil prior to storage. The upper leg, front torso, and back torso pieces are kept separate, and each is wrapped in aluminum foil prior to storage. 

TABLE 38-3. Frequently Used Medications for Restless-Legs Syndrome49... 

In Table IV are tabulated the concentrations of DDT found in the tissues of the chickens killed after one year of feeding. The concentration of DDT was markedly higher in the fat than in the diet. Only small amounts of the insecticide were found in the breast and leg muscle tissues. In each case the fatty tissues contained DDT at markedly higher levels than the eggs. 

The kitchen has an ancient bottled-gas stove, a Formica table with an oil lamp on it and a scatter of jewelry tools and materials, a tiled fireplace laid ready with raw-smelling coal, and a beautiful inlaid Queen Anne wall clock tocking away in the corner, showing the phases of the moon and the movement of the sun through the zodiac. As I head out of the back door and find the privy, a black shadow of a cat with blue eyes slips past my legs and away like warm smoke. 

Table 4 presents the amounts of chlorpyrifos used to fortify the various substrates in this study. Chlorpyrifos "low" spike levels for coverall sections (arms, legs, and torso) as well as t-shirts and briefs, handwashes, and head patches ranged from 5.1 pg to 1198 pg. "High" spike levels of these substrates ranged form 1456 pg to 191,720 pg. Air tubes and Gelman filters were fortified with only "low" amounts of chlorpyrifos which ranged from 0.1 pg to 36 pg. 

---