Suppliers Data

Process Conceptual Design Equipment selection and sizing Inventory of process Single vs. Multiple trains Utility requirements Overdesign and flexibility Recycles and buffer capacities Instrumentation and control Location of plant Preliminary plant layout Materials of construction As above plus equipment suppliers data, raw materials data, company design procedures and requirements... 

However, if suppliers data were to be applied without a complete analysis of the test data for each property, the result could prove costly and embarrassing. The nature of plastic materials is such that an oversight of even a small detail in its properties or the method by which they were derived could result in problems and product failure. 

The wheat bran used in these studies was milled for us from a single lot of Waldron hard red spring wheat. Other foods and diet ingredients were purchased from local food suppliers. Data from HS-I was analyzed statistically by Student s paired t test, each subject acting as his own control. A three-way analysis of variance (ANOVA) was performed to test for significant differences betwen diet treatments, periods and individuals in HS-II and HS-III. 

International Chemical Safety Cards and NIOSH Pocket Guides, 75 manufacturer and supplier data, 72-73... 

The density of the polyurethane needs to be known. This may be determined experimentally or from the material suppliers data used. In this example, the volume is assumed to be 1.10 liters and the density of the polyurethane is 1.07 g/m3. 

The information and data presented in this book are not intended to be used as a substitute for more up-to-date and accurate information on the specific plastics and processes. Such specific details can be obtained from in-house sources, testing laboratories, computer databases, material suppliers, data/information sources, consultants, and various institutions. References in this book represent examples for additional sources of plastics and processes. 

For linear fractions of dextrans in water, Senti, et al. 12) reported values of 97.8 X 10 and 0.50 for the constants, and for branched dextrans the value of the exponent was 0.20. Cerney, et al. 16) reported values of 10.3 X 10 and 0.25 for branched dextrans in methanol-water. The suppliers data in 0.05 M Na2S04 yields values of 9 X 10 and 0.50 at 30 °C for a broad range of molecular weights 17). The results of this work are in line with those reported for dextrans, and the exponent corresponds to that for a highly branched coil about 0.0-0.5 18). 

Commodity Supplier Data Bureau of Internal Revenue Internal Revenue Bulletin Alcohol Tax Unit... 

Appendices 8.11, 8.12 and 8.13 open up a relatively new topic where a possible technical gap between the information given in polymer supplier data sheets and the properties of the plastic used in the final pack can be identified. 

Method Database /supplier Data Compounds Remarks... 

The values for FAW and FD can be found in the material suppliers data sheets. The thickness h measurement requires greater care with specimens having a bag side (usually produees a rougher surface than the tool side). 

Note values are those reported in suppliers data sheets. Please eoutaet the supplier for values to be used in speeiheations. 

Sources Supplier data sheets and CRC Handbook of Solubility Parameters and Other Cohesion Parameters, 2nd Ed., (A. Barton, ed.) CRC Press (1991). 

Source Compiled from various suppliers data sheets. Contact suppliers for specification values. 

Note Many sections are accompanied by suppliers data sheets. 

There are three important sources of data and information on RPs. Obtain data from products your organization previously fabricated there is the data sheet compiled by a manufacturer of the material and derived from tests conducted in accordance with standardized specifications. If suppliers data were to be applied without a complete analysis of the test data for each property, the result could prove costly and embarrassing. Final source is preparing your own test specimens and conducting your own tests. Either one or both specimen preparation and test evaluation could be conducted by an outside source. If the fabricator prepares the specimens a duplicate of the fabricating process to be used will be produced or as close to the process as possible. The amount and degree of testing is usually related to factors such as (I) if a prototype is to be prepared and tested and (2) product requirement such as safety. 

CibaTINUVlN 622, supplier data sheet. Ciba Specialty Chemicals, Inc. 1999. 

Superb antistat for PE food packaging with GRINSTED PGE 308, supplier data sheet. Danisco USA. 

Efficient antistat performance in PP injection molding applications with DIMODAN HS K-A, supplier data sheet. Danisco A/S. 

Product information ExCAL CW calcium carbonate, supplier data sheets. Excalibar Minerals Inc. 2005. 

Transmare 14CNF30.0.001, supplier data sheet. Transmare Compounding B.V. 28 June 2006. 

Cel-Span 306P, supplier data sheet. Phoenix Plastics Co., Inc. 

DuPont Entira Strong Polymer Modifier, supplier data sheet (K-11015 5/06). DuPont 2006. 

MCX 111281 Antimicrobial Masterbatch, supplier data sheet. RTP Company 15 January 2007. 

---