Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Suitability for processing

PCTFE plastic is available in products that conform to ASTM 1430-89 Type 1 (Grades 1 and 2) and is suitable for processing into parts that meet MIL-P 46036 (Federal Specification LP-385C was canceled 1988). Standards for fabricated forms are available for compression molded heavy sections (AMS-3645 Class C), thin-walled tubing, rod, sheet, and molded shapes (AMS-3650). PCTFE plastics have been approved for use in contact with food by the FDA (55). [Pg.394]

Roto-Louvre diyers are suitable for processing coarse granular solids which do not offer high resistance to air flow, require intimate gas contacting, and do not contain significant quantities of dust. [Pg.1212]

It is for these reasons that pneumatic equipment is especially suitable for processing heat-sensitive, easily oxidized, explosive, or flammable materials wriich cannot be exposed to process conditions for extended periods. [Pg.1225]

Most domestic battery scrap is processed in blast furnaces, rotary furnaces, or reverberatory furnaces. A reverberatory furnace is more suitable for processing fine particles and may be operated in conjunction with a blast furnace. [Pg.131]

This method is suitable for processing routine orders however, where there are nonstandard conditions a more variable process needs to be developed. Providing you define the approach you intend to take in your procedures, you should be able to demonstrate that your methods provide an adequate degree of control. [Pg.328]

Concentrates of columbate-tantalate are most suitable for processing and are most frequently used in the production of tantalum, niobium and their compounds. [Pg.253]

The instrument has been evaluated by Luster, Whitman, and Fauth (Ref 20). They selected atomized Al, AP and NGu as materials for study that would be representative of proplnt ingredients. They found that only 2000 particles could be counted in 2 hours, a time arbitrarily chosen as feasible for control work. This number is not considered sufficient, as 18,000 particles are required for a 95% confidence level. Statistical analysis of results obtained for AP was impossible because of discrepancies In the data resulting from crystal growth and particle agglomeration. The sample of NGu could not be handled by the instrument because it consisted of a mixt of needles and chunky particles. They concluded that for dimensionally stable materials such as Al or carborundum, excellent agreement was found with other methods such as the Micromerograph or visual microscopic count. But because of the properties peculiar to AP and NGu, the Flying Spot Particle Resolver was not believed suitable for process control of these materials... [Pg.531]

Tucker, G. and Heydon, G Trans.I.Chem.E. 76 Part C (1998) 208. Food particle residence time measurement for the design of commercial tubular heat exchangers suitable for processing suspensions of solids im liquids,... [Pg.229]

To develop the rate equations suitable for process modeling and reactor design, experimental data have been analyzed on the basis of the postulated reaction mechanism [2] given in Table 1. Here the formation of polymer is excluded because it is not detected under our experimental conditions. All of the reactions are equilibrium-limited and the net rates for the formation of each component with some assumptions [3] are given as follows ... [Pg.709]

In this study the problem of estimating an unknown function from its examples is revisited. Its mathematical description is attempted to map as closely as possible the practical problem that the potential NN user has to face. The objective of the chapter is twofold (1) to draw the framework in which NN solutions to the problem can be developed and studied, and (2) to show how careful considerations on the fundamental issues naturally lead to the Wave-Net solution. The analysis will not only attempt to justify the development of the Wave-Net, but will also refine its operational characteristics. The motivation for studying the functional estimation problem is the derivation of a modeling framework suitable for process control. The applicability of the derived solution, however, is not limited to control implementations. [Pg.161]

Many analytical techniques are in use for the qualitative and quantitative evaluation of monomers and oligomers extracted from PA6 (GC, differential refrac-tometry, IR, PC, SEC, HPLC, RPLC, etc.). FTIR has been used for quantitative analysis of caprolactam oligomer content (extract %) in polyamide-6 [113], The method, which involves a 3h extraction in boiling methanol, is suitable for process control and plant environment. Kolnaar [114] has used FTIR characterisation of fractional extracts with pentane, hexane, and heptane of HDPE for blow moulding applications. Vinyl acetate in packaging film has similarly been determined by quantitative FUR. [Pg.316]

This type is similar in principle to the tank type, but the cooling surfaces are continually scraped or agitated to prevent the fouling by deposited crystals and to promote heat transfer. They are suitable for processing high-viscosity liquors. Scraped-surface... [Pg.438]

The three basic types of impeller which are used at high Reynolds numbers (low viscosity) are shown in Figures 10.55a, b, c. They can be classified according to the predominant direction of flow leaving the impeller. The flat-bladed (Rushton) turbines are essentially radial-flow devices, suitable for processes controlled by turbulent mixing (shear controlled processes). The propeller and pitched-bladed turbines are essentially axial-flow devices, suitable for bulk fluid mixing. [Pg.470]

As the gas cools the Internal pressure will decrease until It reaches a level suitable for processing through the ventilation system. [Pg.245]

Readily available, inexpensive titanium grade 2 is a suitable SCWO reactor liner material for TD and MD, and with the addition of a titanium wear liner, as shown in Figure 5-2, it is suitable for processing GB and HD. [Pg.144]

Bulk physical property tests, such as density and heating value, as well as some compositional tests, such as the Orsat analysis and the mercuric nitrate method for the determination of unsaturation, are still used. However, the choice of a particular test is dictated by (1) the requirements of the legislation, (2) the properties of the gas under study, and (3) the selection by the analyst of a suitable suite of tests to meet the various requirements. For example, judgment by the analyst is necessary whether or not a test that is applied to liquefied petroleum gas is suitable for process gas or natural gas insofar as inference from the nonhydrocarbon constituents will be minimal. [Pg.248]

This section describes characteristics and selection of commercially available spectral and photometric LIE process instruments. While a comprehensive assessment was the objective, the author acknowledges that some vendors and instruments may have been inadvertently omitted. Nevertheless, the following survey of LIE instruments suitable for process and field enviromnents was based on instruments defined within scientific literature and those actively marketed by common process analytical instrument vendors. Thus, emerging in-line LIE instruments is perhaps a potential gap within the following discussion. [Pg.343]

The design of the stack was inadequate for the service especially since the scrubbing process introduced solid material into the stack. A good structural or mechanical design does not necessarily ensure suitability for process conditions. The stack should have been reinforced and should have been equipped with some means of minimizing deposits within the inner liner. [Pg.347]

Research to develop a catalyst suitable for processing of residual feedstocks has focused on the many faceted requirements of such a catalyst. [Pg.336]


See other pages where Suitability for processing is mentioned: [Pg.616]    [Pg.52]    [Pg.210]    [Pg.528]    [Pg.1088]    [Pg.489]    [Pg.815]    [Pg.915]    [Pg.193]    [Pg.443]    [Pg.438]    [Pg.88]    [Pg.510]    [Pg.22]    [Pg.271]    [Pg.25]    [Pg.195]    [Pg.22]    [Pg.6]    [Pg.4]    [Pg.172]    [Pg.67]    [Pg.9]    [Pg.239]    [Pg.348]    [Pg.93]    [Pg.166]    [Pg.169]    [Pg.169]    [Pg.426]    [Pg.172]   


SEARCH



Suitability

© 2024 chempedia.info