Substituted dissolution

We have formulated defect reactions which describe intrinsic ionic and electronic disorder, nonstoichiometry, variable ionisation of point defects, and substitutional dissolution of aliovalent cations and ions and anions. Ahovalent elements may be compensated by electronic defects or by point defects, of which the former involve red-ox-reactions. 

Iodine is only slightly soluble in water and no hydrates form upon dissolution. The solubiHty increases with temperature, as shown in Table 2 (36). Iodine is soluble in aqueous iodide solutions owing to the formation of polyiodide ions. For example, an equiHbrium solution of soHd iodine and KI H2O at 25°C is highly concentrated and contains 67.8% iodine, 25.6% potassium iodide, and 6.6% water. However, if large cations such as cesium, substituted ammonium, and iodonium are present, the increased solubiHty may be limited, owing to precipitation of sparingly soluble polyiodides. Iodine is also more... 

This type of cement has been further improved by the substitution of -hexyl van ill ate [84375-71-3] and similar esters of vanillic acid [121 -34-6] and/or syringic acid [530-57 ] for eugenol (93—95). These substituted cements are strong, resistant to dissolution, and, unlike ZOE and EBA cements, do not inhibit the polymerization of resin-base materials. Noneugenol cements based on the acid—base reaction of zinc and similar oxides with carboxyhc acids have been investigated, and several promising types have been developed based on dimer and trimer acids (82). 

Planar-octahedral equilibria. Dissolution of planar Ni compounds in coordinating solvents such as water or pyridine frequently leads to the formation of octahedral complexes by the coordination of 2 solvent molecules. This can, on occasions, lead to solutions in which the Ni has an intermediate value of jie indicating the presence of comparable amounts of planar and octahedral molecules varying with temperature and concentration more commonly the conversion is complete and octahedral solvates can be crystallized out. Well-known examples of this behaviour are provided by the complexes [Ni(L-L)2X2] (L-L = substituted ethylenediamine, X = variety of anions) generally known by the name of their discoverer I. Lifschitz. Some of these Lifschitz salts are yellow, diamagnetic and planar, [Ni(L-L)2]X2, others are blue, paramagnetic, and octahedral, [Ni(L-L)2X2] or... 

In principle, the oxidation of proceeds at an electrode potential that is more negative by about 0.7 V than the anodic decomposition paths in the above cases however, because of the adsorption shift, it is readily seen that practically there is no energetic advantage compared to CdX dissolution in competing for photogenerated holes. Similar effects are observed with Se and Te electrolytes. As a consequence of specific adsorption and the fact that the X /X couples involve a two-electron transfer, the overall redox process (adsorption/electron trans-fer/desorption) is also slow, which limits the degree of stabilization that can be attained in such systems. In addition, the type of interaction of the X ions with the electrode surface which produces the shifts in the decomposition potentials also favors anion substitution in the lattice and the concomitant degradation of the photoresponse. 

Pancreatic enzyme replacement is the mainstay of gastrointestinal therapy. Most enzyme products are formulated as capsules containing enteric-coated microspheres or microtablets to avoid inactivation of enzymes in the acidic stomach instead, they dissolve in the more alkaline environment of the duodenum. Capsules may be opened and the microbeads swallowed with food, as long as they are not chewed. A powder form is available for patients unable to swallow the capsules or microbeads, but bioavailability is poor. While products may contain similar enzyme ratios, they are not bioequivalent and cannot be substituted. Generic enzyme products generally display poor dissolution and should not be used.5 Table 13-3 lists commonly used enzyme replacement products. 

Addition of an alkali metal oxide as a "network modifier to the "network former causes pH sensitivity, i.e., small amounts of alkali metal induce superficial gel layer formation as a merely local chemical attack and so with limited alkali error larger amounts will result in more pronounced dissolving properties of the glass up to complete dissolution, e.g., water-glass with large amounts of sodium oxide. Simultaneous addition of an alkaline earth metal oxide, however, diminishes the dissolution rate. Substitution of lithium for sodium in pH-sensitive glass markedly reduces the alkali error. 

Azoniaspiro[4.8]tridecane 129 was formed from the substituted triazacyclononane 128 (X = OMe) on standing in methanol for ten days (Scheme 15) <2000AJC791 >. It was precipitated as the tetraphenylborate salt 130 (X = BPli, ) since attempts to isolate the methoxide derivative by evaporation of the solvent led to elimination reactions yielding a mixture of triazacyclononane 131 and allene 132 in the ratio of 1 10. Re-dissolution of these allows further hydro-amination reactions to occur. Precipitation and analysis of their tetraphenylborate salts suggested the products to be 130-132 in a ratio of 1 8 1. Owing to their chemical similarities these components were not isolated. 

Dependence on Base Concentration. The dissolution rates of substituted PHHPs at different alkali concentrations are displayed 1n Figure 1 for seven different novolac resins. In each case, there appears to be a limiting concentration C0 below which the rate of dissolution 1s too slow to be measured 1n the experimental time scale. The ascending portion of the curve can be represented by a power law dependence of the rate on concentration C, eq.(1),... 

Figure 1. Dissolution of para-substituted PHMPs at different KOH concentrations.

The workhorse of the VLSI industry today is a composite novolac-diazonaphthoquinone photoresist that evolved from similar materials developed for the manufacture of photoplates used in the printing industry in the early 1900 s (23). The novolac matrix resin is a condensation polymer of a substituted phenol and formaldehyde that is rendered insoluble in aqueous base through addition of 10-20 wt% of a diazonaphthoquinone photoactive dissolution inhibitor (PAC). Upon irradiation, the PAC undergoes a Wolff rearrangement followed by hydrolysis to afford a base-soluble indene carboxylic acid. This reaction renders the exposed regions of the composite films soluble in aqueous base, and allows image formation. A schematic representation of the chemistry of this solution inhibition resist is shown in Figure 6. 

---