Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Insertion Subject

An elementary account of the subject has been given in the previous Section. For the fractional distillation under diminished pressure of liquids diflfering only slightly in boiling point, a firactionating column (see Sections 11,15 and 11,17) must be used. Provision must, of course, be made for the insertion of a capillary tube into the fiask containing the mixture. This can be done by any of the following methods —... [Pg.119]

The small-spiral-large-sbaft type (Fig. ll-60b) is inserted in a solids-product line as pipe banks are in a fluid line, solely as a heat-transfer device. It features a thin burden ring carried at a high rotative speed and subjected to two-sided conductance to yield an estimated heat-transfer coefficient of 285 W/(m °C) [50 Btu/(h fU °F)], thereby ranking thermally next to the sheU-fluidizer type. This device for powdered solids is comparable with the Votator ol the fluid field. [Pg.1094]

There is much evidence that there are many cases in which the interaction between liquids and solids cannot be described in terms of dispersion forces alone. For example, Dann [75] found significant non-dispersion-force contributions to the work of adhesion between ethanol/water mixtures, mixed glycols, and polyglycols and a mixture of formamide and 2-ethoxyethanol against a variety of solids. The nature of these other interactions , however, were at first the subject of some dispute. We may account for them in a general way with a term /sl inserted into Eq. 11 ... [Pg.33]

Example 2.1 A ball-point pen made from polypropylene has the clip design shown in Fig. 2.11. When the pen is inserted into a pocket, the clip is subjected to a deflection of 2 mm at point A. If the limiting strain in the material is to be 0.5% calculate (i) a suitable thickness, d, for the clip (ii) the initial stress in the clip when it is first inserted into the pocket and (iii) the stress in the clip when it has been in the pocket for 1 week. The creep curves in Fig. 2.5 may be used and the short-term modulus of polypropylene is 1.6 GN/m. ... [Pg.54]

Frequently, a product becomes loaded when it is subjected to a defined deflection. The actual load then is a result of the structural reaction of the product to the applied strain. Unlike directly applied loads, strain-induced loads are dependent on the modulus of elasticity and, with TPs, will generally decrease in magnitude over time. Many assembly and thermal stresses could be the result of strain-induced loads. They include metal insert press fits in the plastic and clamping or screw attachments. [Pg.138]

The subject of transmitting motion and power by means of gears, their construction, and detail requirements are fully covered in textbooks, technical handbooks, and industrial literature of gear suppliers. The knowledge of gear fundamentals is a prerequisite for the understanding of where and how to insert the appropriate plastic behavioral information into the gear formulas so that the application results in favorable operation. [Pg.220]

Recombinant protein is a protein produced by a genetically modified cell or an organism, which expresses a DNA that was subjected to recombination and inserted into its genome. [Pg.1063]

The Rieske protein II (SoxF) from Sulfolobus acidocaldarius, which is part, not of a bci or b f complex, but of the SoxM oxidase complex 18), could be expressed in E. coli, both in a full-length form containing the membrane anchor and in truncated water-soluble forms 111). In contrast to the results reported for the Rieske protein from Rhodobacter sphaeroides, the Rieske cluster was more efficiently inserted into the truncated soluble forms of the protein. Incorporation of the cluster was increased threefold when the E. coli cells were subject to a heat shock (42°C for 30 min) before induction of the expression of the Rieske protein, indicating that chaperonins facilitate the correct folding of the soluble form of SoxF. The iron content of the purified soluble SoxF variant was calculated as 1.5 mol Fe/mol protein the cluster showed g values very close to those observed in the SoxM complex and a redox potential of E° = +375 mV 111). [Pg.146]

The subjects of structure and bonding in metal isocyanide complexes have been discussed before 90, 156) and will not be treated extensively here. A brief discussion of this subject is presented in Section II of course, special emphasis is given to the more recent information which has appeared. Several areas of current study in the field of transition metal-isocyanide complexes have become particularly important and are discussed in this review in Section III. These include the additions of protonic compounds to coordinated isocyanides, probably the subject most actively being studied at this time insertion reactions into metal-carbon bonded species nucleophilic reactions with metal isocyanide complexes and the metal-catalyzed a-addition reactions. Concurrent with these new developments, there has been a general expansion of descriptive chemistry of isocyanide-metal complexes, and further study of the physical properties of selected species. These developments are summarized in Section IV. [Pg.22]

This chapter is concerned entirely with the insertion of carbon monoxide into transition metal-carbon cr-bonds. Sulfur dioxide insertion 154, 239), also common among transition metal-carbon complexes, will be treated in a complementary review, which is to appear later. Subject to the restrictions given at the beginning of Section VI, an attempt has been made at a complete literature coverage of the insertion of CO. Particular emphasis focuses on recent results, especially those of a kinetic and stereochemical nature. [Pg.90]

CO insertion (as inferred from the nature of products), but in which the actual insertion or decarbonylation step has received at most peripheral attention. This particularly applies to industrial carbonylation processes such as hydroformylation. The interested reader is referred to several excellent articles on these subjects (30, 32, 62, 117, 198a, 203a, 228). [Pg.118]

Palladium(O)- and Pd(II)-catalyzed carbonylation reactions have been the subject of several recent articles 32, 116, 119, 124, 173, 228, 232). In one case, the attending CO insertion into a Pd—C bond was shown to proceed with retention of configuration at carbon 131a, 218). [Pg.138]


See other pages where Insertion Subject is mentioned: [Pg.24]    [Pg.101]    [Pg.24]    [Pg.101]    [Pg.466]    [Pg.67]    [Pg.331]    [Pg.416]    [Pg.254]    [Pg.48]    [Pg.196]    [Pg.34]    [Pg.341]    [Pg.341]    [Pg.230]    [Pg.157]    [Pg.1233]    [Pg.338]    [Pg.112]    [Pg.368]    [Pg.257]    [Pg.1134]    [Pg.322]    [Pg.221]    [Pg.1067]    [Pg.171]    [Pg.569]    [Pg.572]    [Pg.183]    [Pg.434]    [Pg.842]    [Pg.33]    [Pg.102]    [Pg.246]    [Pg.123]    [Pg.127]    [Pg.135]    [Pg.80]    [Pg.619]    [Pg.589]   
See also in sourсe #XX -- [ Pg.2 , Pg.3 , Pg.4 , Pg.11 , Pg.14 ]




SEARCH



Subject insertion reactions

Subject migratory insertion

© 2024 chempedia.info