Sterically stabilized

Anotlier model system consists of polymetliylmetliacrylate (PMMA) latex, stabilized in organic solvents by a comb polymer, consisting of a PMMA backbone witli poly-12-hydroxystearic acid (PHSA) chains attached to it [10]. The PHSA chains fonn a steric stabilization layer at tire surface (see section C2.6.4). Such particles can approach tire hard-sphere model very well [111. 

In practice, tliere are various ways by which ( ) can be detennined for a given sample, and tire results may be (slightly) different. In particular, for sterically stabilized particles, tire effective hard-sphere volume fraction will be different from tire value obtained from tire total solid content. 

Because model colloids tend to have a ratlier well defined chemical composition, elemental analysis can be used to obtain detailed infonnation, such as tlie grafted amount of polymer in tire case of sterically stabilized particles. More details about tire chemical stmcture can be obtained using NMR techniques (section B1.13). In addition, NMR... 

For so-called steric stabilization to be effective, tire polymer needs to be attached to tire particles at a sufficiently high surface coverage and a good solvent for tire polymer needs to be used. Under such conditions, a fairly dense polymer bmsh witli tliickness L will be present around the particles. Wlren two particles approach, such tliat r < d + 2L, tire polymer layers may be compressed from tlieir equilibrium configuration, tluis causing a repulsive interaction. 

Finally, we briefly mention interactions due to adsorbing polymers. Block copolymers, witli one block strongly adsorbing to tire particles, have already been mentioned above. Flere, we focus on homopolymers tliat adsorb moderately strongly to tire particles. If tliis can be done such tliat a high surface coverage is achieved, tire adsorbed polymer layer may again produce a steric stabilization between tire particles. 

The behaviour of tliese systems is similar to tliat of suspensions in which short-range attractions are induced by changing solvent quality for sterically stabilized particles (e.g. [103]). Anotlier case in which narrow attractions arise is tliat of solutions of globular proteins. These crystallize only in a narrow range of concentrations [104]. 

Disc-like particles can also undergo an Onsager transition—here tire particles fonn a discotic nematic, where tire short particle axes tend to be oriented parallel to each other. In practice, clay suspensions tend to display sol-gel transitions, witliout a clear tendency towards nematic ordering (for instance, [22]). Using sterically stabilized platelets, an isotropic-nematic transition could be observed [119]. 

Steric stabilization Sterilant Sterilants Sterile filling Sterile filtration... 

Surface Modification. Reaction or adsorption at the soHd surface can alter its properties and lead to a surface charge or steric stabilization... 

Chemical Grafting. Polymer chains which are soluble in the suspending Hquid may be grafted to the particle surface to provide steric stabilization. The most common technique is the reaction of an organic silyl chloride or an organic titanate with surface hydroxyl groups in a nonaqueous solvent. For typical interparticle potentials and a particle diameter of 10 p.m, steric stabilization can be provided by a soluble polymer layer having a thickness of - 10 nm. This can be provided by a polymer tail with a molar mass of 10 kg/mol (25) (see Dispersants). 

Because of this interaction, PVP has found appHcation in surfactant formulations, where it functions as a steric stabilizer for example to generate uniform particle-size polystyrene emulsions (110—112). In a variety of formulations, a surfactant s abiHty to emulsify is augmented by PVP s abiHty to stabilize coUoids stericaHy and to control rheology. 

Deflocculants. Deflocculants (34), dispersants (qv), or anticoagulants are added to slurries to improve dispersion and dispersion stabiHty. Dispersants break up floes in a slurry by lowering van der Waals interparticle forces. Deflocculants adsorb on particle surfaces and prevent the approach of particles either by electrostatic or steric stabilization. Deflocculation by electrostatic stabilization is common in clay slurries, as weU as with ceramic particles dispersed in polar Hquids such as water. 

Oleic acid is a good deflocculant for oxide ceramic powders in nonpolar Hquids, where a stable dispersion is created primarily by steric stabilization. Tartaric acid, benzoic acid, stearic acid, and trichloroacetic acid are also deflocculants for oxide powders in nonpolar Hquids. 

DLVO Theory. The overall stabiUty of a particle dispersion depends on the sum of the attractive and repulsive forces as a function of the distance separating the particles. DLVO theory, named for Derjaguin and Landau (11) and Verwey and Overbeek (12), encompasses van der Waals attraction and electrostatic repulsion between particles, but does not consider steric stabilization. The net energy, AGp between two particles at a given distance is the sum of the repulsive and attractive forces ... 

Suppose we have a physical system with small rigid particles immersed in an atomic solvent. We assume that the densities of the solvent and the colloid material are roughly equal. Then the particles will not settle to the bottom of their container due to gravity. As theorists, we have to model the interactions present in the system. The obvious interaction is the excluded-volume effect caused by the finite volume of the particles. Experimental realizations are suspensions of sterically stabilized PMMA particles, (Fig. 4). Formally, the interaction potential can be written as... 

FIG. 4 Sterically stabilized colloidal particles are coated with short polymer brushes. A hard sphere-like interaction arises. 

The hard sphere (HS) interaction is an excellent approximation for sterically stabilized colloids. However, there are other interactions present in colloidal systems that may replace or extend the pure HS interaction. As an example let us consider soft spheres given by an inverse power law (0 = The energy scale Vq and the length scale cr can be com-... 

Monosized polystyrene particles in the size range of 2-10 /am have been obtained by dispersion polymerization of styrene in polar solvents such as ethyl alcohol or mixtures of alcohol with water in the presence of a suitable steric stabilizer (59-62). Dispersion polymerization may be looked upon as a special type of precipitation polymerization and was originally meant to be an alternative to emulsion polymerization. The components of a dispersion polymerization include monomers, initiator, steric stabilizer, and the dispersion medium... 

Theoretical Studies of Enzymic Reactions Dielectric, Electrostatic and Steric Stabilizations of the Carbonium Ion in the Reaction of Lysozyme A. Warshel and M. Levitt Journal of Molecular Biology 103 (1976) 227-249... 

Monomer-soluble initiators are used in this polymerization technique. The monomer phase containing an initiator is dissolved in an inert solvent or solvent mixture including a steric stabilizer. The polymers or oligomer... 

Figure 9 The schematical representation of dispersion polymerization process, (a) initially homogeneous dispersion medium (b) particle formation and stabilizer adsorption onto the nucleated macroradicals (c) capturing of radicals generated in the continuous medium by the forming particles and monomer diffusion to the forming particles (d) polymerization within the monomer swollen latex particles, (e) latex particle stabilized by steric stabilizer and graft copolymer molecules (f) list of symbols.

Some typical dispersion polymerization recipes and the electron micrograph of the uniform polymeric particles with Recipe I are given in Table 5 and Fig. 10, respectively. As seen in Table 5, the alcohols or alcohol-water mixtures are usually utilized as the dispersion media for the dispersion polymerization of apolar monomers. In order to achieve the monodispersity in the final product, a costabilizer can be used together with a primary steric stabilizer, which is usually in the polymeric form as in... 

One commonly used procedure for studying the steric stability of the carbanion is comparison of the rate of base-catalyzed H/D exchange reaction (kel) on the chiral carbon with the rate of racemization (fcrac). By this comparison, inversion, racemization or... 

---