Steam Reformers

Steam reforming is, along with catalytic reforming, a process that can produce the additional hydrogen needed for upgrading and converting the heavy fractions of crude oil. 

Phosphoric Acid Fuel Cell. Concentrated phosphoric acid is used for the electrolyte ia PAFC, which operates at 150 to 220°C. At lower temperatures, phosphoric acid is a poor ionic conductor (see Phosphoric acid and the phosphates), and CO poisoning of the Pt electrocatalyst ia the anode becomes more severe when steam-reformed hydrocarbons (qv) are used as the hydrogen-rich fuel. The relative stabiUty of concentrated phosphoric acid is high compared to other common inorganic acids consequentiy, the PAFC is capable of operating at elevated temperatures. In addition, the use of concentrated (- 100%) acid minimizes the water-vapor pressure so water management ia the cell is not difficult. The porous matrix used to retain the acid is usually sihcon carbide SiC, and the electrocatalyst ia both the anode and cathode is mainly Pt. 

Steam reforming of CH is commonly carried out at 750 to 900°C, thus at the lower operating temperature of MCFCs a high activity catalyst is required. The internal reforming of methane in IRMCFCs, where the steam-reforming reaction... 

A viable electrocatalyst operating with minimal polarization for the direct electrochemical oxidation of methanol at low temperature would strongly enhance the competitive position of fuel ceU systems for transportation appHcations. Fuel ceUs that directiy oxidize CH OH would eliminate the need for an external reformer in fuel ceU systems resulting in a less complex, more lightweight system occupying less volume and having lower cost. Improvement in the performance of PFFCs for transportation appHcations, which operate close to ambient temperatures and utilize steam-reformed CH OH, would be a more CO-tolerant anode electrocatalyst. Such an electrocatalyst would reduce the need to pretreat the steam-reformed CH OH to lower the CO content in the anode fuel gas. Platinum—mthenium alloys show encouraging performance for the direct oxidation of methanol. 

Separation, combustion, pyrolysis, hydrogena-tion, anaerobic fermen-tation, aerobic fermen-tation, biophotolysis, partial oxidation, steam reforming, chemical hy-drolysis, enzyme hydrol-ysis, other chemical conversions, natural processes... 

Steam Reforming. When relatively light feedstocks, eg, naphthas having ca 180°C end boiling point and limited aromatic content, are available, high nickel content catalysts can be used to simultaneously conduct a variety of near-autothermic reactions. This results in the essentiaHy complete conversions of the feedstocks to methane ... 

In general, the proven technology to upgrade methane is via steam reforming to produce synthesis gas, CO + Such a gas mixture is clean and when converted to Hquids produces fuels substantially free of heteroatoms such as sulfur and nitrogen. Two commercial units utilizing the synthesis gas from natural gas technology in combination with novel downstream conversion processes have been commercialized. 

Coal gasification technology dates to the early nineteenth century but has been largely replaced by natural gas and oil. A more hydrogen-rich synthesis gas is produced at a lower capital investment. Steam reforming of natural gas is appHed widely on an iadustrial scale (9,10) and ia particular for the production of hydrogen (qv). 

J. R. Rostmp-Nielsen, Steam Reforming Catalysts Teknisk Fodag A/S, Copenhagen, 1975. 

Synthesis Gas Chemicals. Hydrocarbons are used to generate synthesis gas, a mixture of carbon monoxide and hydrogen, for conversion to other chemicals. The primary chemical made from synthesis gas is methanol, though acetic acid and acetic anhydride are also made by this route. Carbon monoxide (qv) is produced by partial oxidation of hydrocarbons or by the catalytic steam reforming of natural gas. About 96% of synthesis gas is made by steam reforming, followed by the water gas shift reaction to give the desired H2 /CO ratio. 

Methane. The largest use of methane is for synthesis gas, a mixture of hydrogen and carbon monoxide. Synthesis gas, in turn, is the primary feed for the production of ammonia (qv) and methanol (qv). Synthesis gas is produced by steam reforming of methane over a nickel catalyst. 

Industrial. The main means of producing hydrogen industrially are steam reforming of hydrocarbons... 

Parameter Steam reforming (SR) Partial oxidation (POX) Texaco gasification (TG) Water electrolysis... 

Steam Reforming. In steam reforming, light hydrocarbon feeds ranging from natural gas to straight mn naphthas are converted to synthesis gas (H2, CO, CO2) by reaction with steam (qv) over a catalyst in a primary reformer furnace. This process is usually operated at 800—870°C and 2.17—2.86... 

Because hydrocarbon feeds for steam reforming should be free of sulfur, feed desulfurization is required ahead of the steam reformer (see Sulfur REMOVAL AND RECOVERY). As seen in Figure 1, the first desulfurization step usually consists of passing the sulfur-containing hydrocarbon feed at about 300—400°C over a Co—Mo catalyst in the presence of 2—5% H2 to convert organic sulfur compounds to H2S. As much as 25% H2 may be used if olefins... 

Fig. 1. Hydrogen production flow sheet, showing steam reforming, shift, hot potassium carbonate CO2 removal, and methanation.

---