Standard Condensation Control

Standard Condensation Control 4.2.1 Standard Assessment Methods... 

Table 4.1 Standard condensation control in roofs (after [4])...

Figure 4.1 Ridge detail for tiled vented roof design, according to standard condensation control practice.

A good condensate control program, using the correct mix of different distribution ratio (DR) neutralizing amines, will minimize corrosion and limit iron transport. A standard control method is often... 

Most of the gnidelines and standards on condensation control in Anglo-Saxon conntries go back to the studies on moisture accumulation in residential woodframe walls and... 

The standards [4] also include rules for the design of ventilated cavities. These design rules are based on analytical calculation methods developed to predict the potential of cavity ventilation for condensation control [11]. 

The principles and measures of condensation control described in scientific reports and applied in the standards have found their way to building industry, designers, contractors and builders through a variety of technical recommendations and commercial publications. Design guidelines may vary from coimtry to country, and range from simple to more differentiated. 

Mercury vapor discharge from vents of reactors or storage tanks at normal atmospheric pressure is controlled readily by means of activated carbon. Standard units (208-L (55-gal) dmms) of activated carbon equipped with proper inlet and outlet nozzles can be attached to each vent. To minimize the load on the carbon-absorbing device, a small water-cooled condenser is placed between the vent and the absorber. 

To meet the 1993 Energy Standards, the industry undertook, at considerable cost, the optimization of the various refrigeration system components. The most significant improvement was the increase in compressor efficiency, from an EER of about 4 to about 5.5. Other system improvements included more efficient fan motors, more effective heat transfer by the evaporator and the condenser, and less defrost energy. In the early 1980s, both the Whirlpool Corporation and White Consolidate Industries introduced electronic defrost controls. Heretofore, an electric timer initiated the defrost cycle, typically every t A elve hours, whether the evaporator needed it or not. With the electronic control the defrost inteiwal is more a function of frost accumulation than of time, and thus referred to as a variable defrost control or as adaptive defrost. It saves energy by being activated only when needed. 

Overall, these features mean that chemical control standards are necessarily high. For example, supplementation of the water treatment plant by condensate polishing plant and periodic chemical cleaning are particularly important. In addition, before each period of operation, a clean-up of the cycle is applied to remove crud. Stringent attention must be paid to the feed-water conditioning. 

For reactions at atmospheric pressure, standard laboratory glassware such as round-bottomed flasks or simple beakers from 0.25 to 2 L can be used. A protective mount in the ceiling of the cavity enables the connection of reflux condensers or distillation equipment. An additional mount in the sidewall allows for sample withdrawal, flushing with gas to create inert atmospheres, or live monitoring of the reaction with a video camera. Most of the published results in controlled MAOS have been obtained from reactions in sealed vessels, and thus in the following mostly accessories for sealed-vessel reaction conditions are described. 

The droplet size distribution produced by vaporization-condensation technique is strongly dependent on the chemical composition and properties of the liquid. If well controlled on a small scale, vaporization-condensation technique can produce moderately mono-disperse sprays with geometric standard deviations ranging from about 1.2 to 1.8.[88]... 

A degree of stereoselective control of the course of a reaction, which is absent or different from that prevalent when the reaction is conducted in the absence of quaternary ammonium salts, may be achieved under standard phase-transfer catalysed reaction conditions. The reactions, which are influenced most by the phase-transfer catalyst, are those involving anionic intermediates whose preferred conformations or configurations can be controlled by the cationic species across the interface of the two-phase system. For example, in the base-catalysed Darzens condensation of aromatic aldehydes with a-chloroacetonitriles to produce oxiranes (Section 6.3), the intermediate anion may adopt either of the two conformations, (la) or (lb) which are stabilized by interaction across the interface by the cations (Scheme 12.1) [1-4]. 

---