Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Spray-spin method

Abe, M., Tamaura, Y., Oishi, M., Saitoh, T., Itoh, T. Gomi, M. (1987). Plating of ferrite film on 8" disc at 70 °C by spray-spin-coating method. IEEE Transactions on Magnetics, MAG-23, 3432-4. [Pg.92]

Typical processing methods - compounding, spraying, spinning ... [Pg.270]

Application is mainly by padding followed by curing at 150-180 °C, although minimum add-on techniques such as slop padding, spraying and foam application have been successful. They can also be applied by discontinuous methods, such as exhaust or dip-spin [501]. [Pg.271]

After the precursor stock solution is prepared, various techniques can be used to coat the substrate, depending on the solution viscosity, required film thickness and coverage. The most common methods in the semiconductor industry are spin- and dip-coating. Other processes that are used for deposition include spray coating and stamping. A summary of the uses, limitations, and advantages of the various thin film deposition methods is reported in Table 2.2. [Pg.49]

Airjet spinning, cotton yarn, <5 17 Airjet textured yarn process, 20 19 Airjet texturing, 19 753 Air-knife chemical finishing, 17 513 Air knife coating, 7 10-11 method summarized, 7 5t Air-laid processes, 11 179-180 Air legislation (EU), 23 121 Airless atomization, in spray coating, 7 69-70... [Pg.24]

In an evaluation of various techniques for droplet generation,1[88] periodic vibration of liquid jet, spinning disk and ultrasonic atomization techniques have been rated as the most appropriate methods for producing monodisperse sprays. These techniques were found to be very effective and appeared promising for refinement,... [Pg.62]

Experimental methods presented in the literature may prove of value in combustion studies of both solid and liquid suspensions. Such suspensions include the common liquid spray. Uniform droplets can be produced by aerosol generators, spinning disks, vibrating capillary tubes, and other techniques. Mechanical, physicochemical, optical, and electrical means are available for determination of droplet size and distribution. The size distribution, aggregation, and electrical properties of suspended particles are discussed as well as their flow and metering characteristics. The study of continuous fuel sprays includes both analytical and experimental procedures. Rayleigh s work on liquid jet breakup is reviewed and its subsequent verification and limitations are shown. [Pg.137]

For some applications it is desirable to prepare aerogels as thin hints that are either self-supporting or supported on another substrate. All common coating methods such as dip coating, spin coating, and spray coating can be used lo prepare gel films. [Pg.43]

Indirect tooling methods are many. Examples include cast aluminum, investment metal cast, cast plastics, cast kirksite, sprayed steel, spin-castings, plaster casting, electroforming, room temperature vulcanizing (RTV) silicone elastomer (Chapter 2 Silicone Elastomer), elastomer/ rubber, reaction injection, stereolithography,338 344 (Table 17.4), direct metal laser sintering, and laminate construction. [Pg.548]


See other pages where Spray-spin method is mentioned: [Pg.363]    [Pg.124]    [Pg.37]    [Pg.155]    [Pg.83]    [Pg.219]    [Pg.297]    [Pg.164]    [Pg.81]    [Pg.1787]    [Pg.1806]    [Pg.4]    [Pg.145]    [Pg.126]    [Pg.156]    [Pg.566]    [Pg.276]    [Pg.304]    [Pg.259]    [Pg.367]    [Pg.44]    [Pg.47]    [Pg.97]    [Pg.210]    [Pg.442]    [Pg.443]    [Pg.191]    [Pg.145]    [Pg.4]    [Pg.126]    [Pg.8]    [Pg.147]    [Pg.67]    [Pg.137]    [Pg.153]    [Pg.240]    [Pg.685]    [Pg.224]   
See also in sourсe #XX -- [ Pg.83 ]




SEARCH



Spinning methods

© 2024 chempedia.info