Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

High-voltage source

The technical specification for this component is perhaps the most difficult of all to meet. Its special requirements derive from two sources high voltage, outdoor environment in polluted conditions. These combine to give an especially demanding specification. [Pg.317]

Protection from on-site sources (high voltage switch gear and supply cables) could be provided by appropriate shielding of the potential sources and by administrative measures (such as in the case of telephones). Protection from off-site interference should be assessed by means of appropriate qualification of equipment [12]. Special attention should be paid to the installation of qualified equipment in order to fulfil the requirements for emissions and immunity. [Pg.64]

Source High voltage High voltage and heating filament High voltage... [Pg.319]

Radiation. Protection against high voltage and fixed isotope sources of radiation is usually a matter of shielding and the observance of strict... [Pg.109]

Fig. 4. A schematic of the plasma source ion implantation system, a plasma source chamber linked to a high voltage pulser. The plasma can be created from... Fig. 4. A schematic of the plasma source ion implantation system, a plasma source chamber linked to a high voltage pulser. The plasma can be created from...
Static eliminating devices that ionize the atmosphere around the device are available. Static eliminators are divided into two main groups silent (corona) discharge eliminators, such as inductive eliminators, or high voltage eliminators which initiate an impact ionization of the air by applying strong electrostatic fields, and radioactive eliminators that provide a multitude of ions from independent ion sources (9). [Pg.289]

PAFC systems are commercially available from the ONSI Corporation as 200-kW stationary power sources operating on natural gas. The stack cross sec tion is 1 m- (10.8 ft"). It is about 2.5 m (8.2 ft) tall and rated for a 40,000-h life. It is cooled with water/steam in a closed loop with secondary heat exchangers. The photograph of a unit is shown in Fig. 27-66. These systems are intended for on-site power and heat generation for hospitals, hotels, and small businesses. Another apphcation, however, is as dispersed 5- to 10-MW power plants in metropolitan areas. Such units would be located at elec tric utihty distribution centers, bypassing the high-voltage transmission system. The market entiy price of the system is 3000/kW. As production volumes increase, the price is projec ted to dechne to 1000 to 1500/kW. [Pg.2412]

Spark Source Mass Spectrometry (SSMS) is a method of trace level analysis—less than 1 part per million atomic (ppma)—in which a solid material, in the form of two conducting electrodes, is vaporized and ionized by a high-voltage radio frequency spark in vacuum. The ions produced from the sample electrodes are accelerated into a mass spectrometer, separated according to their mass-to-charge ratio, and collected for qualitative identification and quantitative analysis. [Pg.45]

An XPS spectrometer schematic is shown in Figure 7. The X-ray source is usually an Al- or Mg-coated anode struck by electrons from a high voltage (10—15 kV) Alka or Mgka radiation lines produced at energies of 1486.6 eV and 1256.6 eV, with line widths of about 1 eV. The X rays flood a large area (-I cm ). The beam s spot size can be improved to about lOO-jim diameter by focusing the electron beam... [Pg.292]

Beyond the complexities of the dispersive element, the equipment requirements of infrared instrumentation are quite simple. The optical path is normally under a purge of dry nitrogen at atmospheric pressure thus, no complicated vacuum pumps, chambers, or seals are needed. The infrared light source can be cooled by water. No high-voltage connections are required. A variety of detectors are avail-... [Pg.417]

Electrical sources static electricity, electrical current, lightning, stray currents (radiofrequency electromagnetic radiation, overhead high voltage transmission lines, galvanic and cathodic protection stray currents)... [Pg.59]


See other pages where High-voltage source is mentioned: [Pg.14]    [Pg.502]    [Pg.224]    [Pg.108]    [Pg.10]    [Pg.269]    [Pg.56]    [Pg.2886]    [Pg.502]    [Pg.14]    [Pg.502]    [Pg.224]    [Pg.108]    [Pg.10]    [Pg.269]    [Pg.56]    [Pg.2886]    [Pg.502]    [Pg.540]    [Pg.63]    [Pg.485]    [Pg.42]    [Pg.399]    [Pg.389]    [Pg.341]    [Pg.109]    [Pg.288]    [Pg.330]    [Pg.331]    [Pg.332]    [Pg.183]    [Pg.2491]    [Pg.225]    [Pg.228]    [Pg.557]    [Pg.59]    [Pg.77]    [Pg.530]    [Pg.598]    [Pg.600]    [Pg.54]    [Pg.215]    [Pg.234]    [Pg.665]    [Pg.716]    [Pg.936]    [Pg.1199]    [Pg.1320]    [Pg.177]   
See also in sourсe #XX -- [ Pg.619 ]




SEARCH



High-voltage

Voltage sources

© 2024 chempedia.info