Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Solutions temperature effects

Charge transfer manifests itself also by a slow establishment of adsorption equilibria mentioned in the preceding text, a slow exchange between adsorbed ions and solution, temperature effects, and the adsorption isotherms of strongly surface-active ions. The latter isotherms demonstrate a slope close to that known for the adsorption of neutral and low-polar species, namely, Hads. for which the Temkin isotherm is applicable [67]. [Pg.344]

Turro, N.J., Aikawa, M., Yekta, A. A comparison of intermolecular and intramolecular excimer formation in detergent solutions temperature effects and microviscosity measurements. J. Am. Chem. Soc. 1979, 101(3), 772-774. [Pg.83]

Concentration and Molecular Weight Effects. The viscosity of aqueous solutions of poly(ethylene oxide) depends on the concentration of the polymer solute, the molecular weight, the solution temperature, concentration of dissolved inorganic salts, and the shear rate. Viscosity increases with concentration and this dependence becomes more pronounced with increasing molecular weight. This combined effect is shown in Figure 3, in which solution viscosity is presented as a function of concentration for various molecular weight polymers. [Pg.338]

First Carbonation. The process stream OH is raised to 3.0 with carbon dioxide. Juice is recycled either internally or in a separate vessel to provide seed for calcium carbonate growth. Retention time is 15—20 min at 80—85°C. OH of the juice purification process streams is more descriptive than pH for two reasons first, all of the important solution chemistry depends on reactions of the hydroxyl ion rather than of the hydrogen ion and second, the nature of the C0 2 U20-Ca " equiUbria results in a OH which is independent of the temperature of the solution. AH of the temperature effects on the dissociation constant of water are reflected by the pH. [Pg.26]

In terms of the solubilities of solutes in a supercritical phase, the following generalizations can be made. Solute solubiUties in supercritical fluids approach and sometimes exceed those of Hquid solvents as the SCF density increases. SolubiUties typically increase as the pressure is increased. Increasing the temperature can cause increases, decreases, or no change in solute solubiUties, depending on the temperature effect on solvent density and/or the solute vapor pressure. Also, at constant SCF density, a temperature increase increases the solute solubiUty (16). [Pg.222]

So far the plate theory has been used to examine first-order effects in chromatography. However, it can also be used in a number of other interesting ways to investigate second-order effects in both the chromatographic system itself and in ancillary apparatus such as the detector. The plate theory will now be used to examine the temperature effects that result from solute distribution between two phases. This theoretical treatment not only provides information on the thermal effects that occur in a column per se, but also gives further examples of the use of the plate theory to examine dynamic distribution systems and the different ways that it can be employed. [Pg.209]

Preparation of Ba-Methyi-17-Hydroxy progesterone 17-Acetate 1 g of 6a-methyl-17a-hy-droxyprogesterone was dissolved in a mixture of 10 ml of acetic acid and 2 ml of acetic anhydride by heating. After solution was effected the mixture was cooled to 15°C, and 0.3 g of p-toluenesulfonic acid was added. After allowing the mixture to stand for a period of 2 /a hours at room temperature, the pink solution was poured into ice water to give an amorphous solid which was recovered by filtration. [Pg.916]

Dissolved oxygen reduction process Corrosion processes governed by this cathode reaction might be expected to be wholly controlled by concentration polarisation because of the low solubility of oxygen, especially in concentrated salt solution. The effect of temperature increase is complex in that the diffusivity of oxygen molecules increases, but solubility decreases. Data are scarce for these effects but the net mass transport of oxygen should increase with temperature until a maximum is reached (estimated at about 80°C) when the concentration falls as the boiling point is approached. Thus the corrosion rate should attain a maximum at 80°C and then decrease with further increase in temperature. [Pg.322]

Temperature effects indicate an activation energy of 113 kJ/mol for Stage I and 16 kJ/mol for Stage II in 7079-T651 alloy. Crack velocity in Stage II is lowered as the solution viscosity is increased. [Pg.1275]

The mechanical properties of Watts deposits from normal, purified solutions depend upon the solution formulation, pH, current density and solution temperature. These parameters are deliberately varied in industrial practice in order to select at will particular values of deposit hardness, strength, ductility and internal stress. Solution pH has little effect on deposit properties over the range pH 1 0-5-0, but with further increase to pH 5 -5, hardness, strength and internal stress increase sharply and ductility falls. With the pH held at 3-0, the production of soft, ductile deposits with minimum internal stress is favoured by solution temperatures of 50-60°C and a current density of 3-8 A/dm in a solution with 25% of the nickel ions provided by nickel chloride. Such deposits have a coarse-grained structure, whereas the harder and stronger deposits produced under other conditions have a finer grain size. A comprehensive study of the relationships between plating variables and deposit properties was made by the American Electroplaters Society and the results for Watts and other solutions reported... [Pg.531]

Temperature effects may also be used in test methods and notably for assessing the effects of inhibitors in acid solutions. The technique is based on that first proposed by Mylius which records the temperature-time behaviour associated with the exothermic reaction resulting from the initial contact of a metal with a corrosive acid solution. The effectiveness of inhibitors may then be determined from their effects on the temperaturetime behaviour. ... [Pg.991]

The behavior of a polar dielectric in an electric field is of the same kind. If the dielectric, is exposed to an external electric field of intensity X, and this field is reduced in intensify by an amount SX, the temperature of the dielectric will not remain constant, unless a certain amount of heat enters the substance from outside, to compensate for the cooling which would otherwise occur. Alternatively, when the field is increased in intensity by an amount SX, we have the converse effect. In ionic solutions these effects are vciy important in any process which involves a change in the intensity of the ionic fields to which the solvent is exposed—that is to say, in almost all ionic processes. When, for example, ions are removed from a dilute solution, the portion of the solvent which was adjacent to each ion becomes free and no longer subject to the intense electric field of the ion. In the solution there is, therefore, for each ion removed, a cooling effect of the kind mentioned above. If the tempera-... [Pg.1]

The solubility of the precipitates encountered in quantitative analysis increases with rise of temperature. With some substances the influence of temperature is small, but with others it is quite appreciable. Thus the solubility of silver chloride at 10 and 100 °C is 1.72 and 21.1mgL 1 respectively, whilst that of barium sulphate at these two temperatures is 2.2 and 3.9 mg L 1 respectively. In many instances, the common ion effect reduces the solubility to so.small a value that the temperature effect, which is otherwise appreciable, becomes very small. Wherever possible it is advantageous to filter while the solution is hot the rate of filtration is increased, as is also the solubility of foreign substances, thus rendering their removal from the precipitate more complete. The double phosphates of ammonium with magnesium, manganese or zinc, as well as lead sulphate and silver chloride, are usually filtered at the laboratory temperature to avoid solubility losses. [Pg.30]

A. Effect of Third Component on Critical Solution Temperature. 195... [Pg.139]


See other pages where Solutions temperature effects is mentioned: [Pg.127]    [Pg.106]    [Pg.222]    [Pg.127]    [Pg.106]    [Pg.222]    [Pg.18]    [Pg.17]    [Pg.167]    [Pg.379]    [Pg.18]    [Pg.262]    [Pg.207]    [Pg.127]    [Pg.221]    [Pg.373]    [Pg.1359]    [Pg.1451]    [Pg.210]    [Pg.275]    [Pg.374]    [Pg.283]    [Pg.41]    [Pg.61]    [Pg.638]    [Pg.128]    [Pg.642]    [Pg.1301]    [Pg.1049]    [Pg.627]   
See also in sourсe #XX -- [ Pg.368 , Pg.369 , Pg.370 ]




SEARCH



Aqueous solutions temperature effects

Bulk solution temperature, effect

Critical solution temperature, effect

Critical solution temperature, effect lower

Critical solution temperature, effect pressure

Critical solution temperature, effect region

Critical solution temperature, effect upper

Effect of Temperature on Polymer Solutions

Effect of temperature and inert solutes

Liquid crystalline solution temperature effect

Solute temperature

Temperature effects on solution

Temperature effects solute solubility, correlation

Temperature solutions

The Combined Effect of Temperature and Solvent Composition on Solute Retention

© 2024 chempedia.info