Sole plates

Most turbomachinery is mounted on structural steel platforms sometimes referred to as base plates or skids. These platforms are then installed on a mass of concrete at the jobsite (either by direct grouting or mounting on sole plates) to become the machinery foundation. Platforms should always be considered as part of the foundation rather than as part of the machinery. 

Check to see that the block between the equipment base and the sole plate is adequate to transmit the load. 

Corners on the edges of the sole plate should have at least a two-ineh radius to prevent the ereation of stress risers and subsequent eraeking of the eorners. 

Base ring type.Sole plates.Accessories. . . . ... 

The injection-compression process is an important variation in which rubber is injected into a partly closed mould under low pressure used for moulding-on of rubber soles to footwear uppers. Rubber is injected into a gap between the shoe upper and the sole plate, which is held 3-4 mm wider than it would be in its final position. After injection at the first mould station of a multistation machine the sole plate is closed in the manner of compression moulding at the second mould station and rubber is pressed along the sole and over the toe cap. The importance of the process is that it becomes possible to mould without using normal high injection pressures which tear and distort canvas, leather or synthetic uppers. 

Ski bindings, shoe components, sole plates for golf shoes. .. 

When specified, pumps shall be provided with a separate sole plate for bolting and grouting to the foundation. This plate shall be machined on its top surface for mounting of the discharge head, can, or motor support. 

The dischaige head mounting surface shall be suitable for grouting or mounting on a machined sole plate. 

Is grouting required for vertically suspended pumps (a sole plate shall Yes No... 

Figure 33 — Typical mounting for vertically-suspended double case pumps (VS6 VS7) with sole plate 8.3.11 Single-casing axial flow (VS3) pumps...

Whon the workstone, a, is not connected with the sole-plate, bw, the space between (hem is filled up with a cement formed from ground bone-ash and galena, thoroughly mixed and pressed firmly into it. Before the wOTkstone, and set in masonry inclosed in a cast-iron jacket, is the, lead-pot, g, into winch the freed metal flows through the channel, a a, whioh is sunk beneath the surface of tho plate. It is placed close to the furnace, in order to prevent the escape of lead... 

Podocytes are polarized cells, so one can differentiate between luminal and abluminal (basal) membrane domains (the basal domain corresponds to the sole plates of the foot processes, which are embedded in the basement membrane). The slit diaphragm forms the border between the luminal and the abluminal membranes. 

Formulation E2-7245 provides excellent lubricity between the treated fabric and the heated sole plate of an iron. The silicone ingredient in this product reduces or eliminates the problem of doughnut-shaped, open-center spray patterns and allows for dispensing in a uniform spray pattern. 

Formulation E2-7246 is an aerosol fabric size that, when repeatedly used, conditions the sole plate of the iron. This silicone conditioning makes ironing easier on all fabrics (even... 

Bottom plate- The "2 by 4 s or 6 s" that lay on the subfloor upon which the vertical studs are installed. Also called the sole plate. ... 

King stud- The vertical "2 X s" frame lumber (left and right) of a window or door opening, and runs continuously from the bottom sole plate to the top plate. 

Mudsill- Bottom horizontal member of an exterior wall frame which rests on top a foundation, sometimes called sill plate. Also sole plate, bottom member of interior wall frame. 

Sole plate- Bottom horizontal member of a frame wall. 

Sole plate- The bottom, horizontal framing member of a wall that s attached to the floor sheeting and vertical wall studs. 

Stud- A vertical wood framing member, also referred to as a wall stud, attached to the horizontal sole plate below and the top plate above. Normally 2 X 4 s or 2 X 6 s, 8 long (sometimes 92 5/8"). One of a series of wood or metal vertical structural members placed as supporting elements in walls and partitions. 

Steam irons are intended to produce steam smoothly and efficiently by having drops of water fall on a small hot area of the metal sole plate called the steam chamber. The steam generated exits through holes in the bottom of the sole plate that is in contact with the fabric. However, when the iron is new, the clean metal surface of the steam chamber is likely to act like a metal griddle. The water droplet will dance around the surface on a thin layer of steam. The contact with the metal surface is minimal and so is the rate of steam production. 

In order to accomplish these criteria, the sole plates are cleaned before the material is applied. This can be done... 

Boots or shoes with in-built toe-caps can give protection against impact or falling objects and, when fitted with a mild steel sole plate, can also provide protection from sharp objects penetrating through the sole. Special slip-resistant soles can also be provided for employees working in wet areas. 

X 225 mm timber sole plate when standing on soil... 

---