Rheological measurements rheometer

Rheological Measurements of Bitumens Using Dynamic Shear Rheometers ... 

Rheological Measurements Three types of rheological measurements have been carried out. In the first type, transient (creep) measurements were performed on a 20% w/w dispersion of latex A, as a function of coverage by PVA. These experiments were carried out using a "Deer" rheometer (PDR 81, Integrated Petronic Systems, London) fitted with a stainless steel concentric cylinder. The procedures used have been described in detail before (21,22). 

There are a number of techniques that are used to measure polymer viscosity. For extrusion processes, capillary rheometers and cone and plate rheometers are the most commonly used devices. Both devices allow the rheologist to simultaneously measure the shear rate and the shear stress so that the viscosity may he calculated. These instruments and the analysis of the data are presented in the next sections. Only the minimum necessary mathematical development will he presented. The mathematical derivations are provided in Appendix A3. A more complete development of all pertinent rheological measurement functions for these rheometers are found elsewhere [9]. 

Melt flow rheology measurements were obtained on the MBAS polymer using an Instron capillary rheometer. The data reported were obtained using an 0.056-inch capillary, 90° included angle, with an L/D of 36. In Figure 5 the maximum shear stress (lb/in2) is plotted vs. the apparent shear rate (sec 1). The apparent viscosity (lb-sec/in2) vs. tem-... 

Rheological measurements were carried out at a Dynamic Analyzer Rheometer RDA II from Rheometrics. Parallel plate geometry with a plate diameter of 25 mm was used to perform the tests where thin films of materials of 1 mm thickness were inserted. To ensure the viscoelastic... 

The capillary rheometer is a valuable tool for predicting the processability of thermoplastic resins. This is done by measuring melt viscosities at shear rates and temperatures commonly encountered in extrusion and injection molding. This procedure is difficult and time consuming due to the complex nature of rheological measurements and analyses. An automated system for acquisition and analyses of capillary rheometer data has been developed to speed up and simplify this important analytical technique. 

Rheology Rheological measurements were performed at 25°C with an ARES 2 KFRT controlled strain rheometer (Rheometric Scientific). For the measurements parallel plates of 50 mm diameter were used. The gels were loaded between the plates (2-mm gap) and allowed to rest for 3 min. A strain sweep (0.1 to 100%) was performed at 1 Hz frequency to determine the range of viscoelasticity for each sample and a 2% strain was selected for all samples. A frequency sweep test (0.1 to 16 Hz) was then performed. Samples of 30 and 50% s/w concentration could not be analyzed because of the difficulty in obtaining samples of proper and constant geometry. 

One very important point that must be considered in any rheological measurement is the possibility of slip during the measurements. This is particularly the case with highly concentrated dispersions, whereby the flocculated system may form a plug in the gap of the platens, leaving a thin liquid film at the walls of the concentric cylinder or cone-and-plate geometry. This behaviour is caused by some syneresis of the formulation in the gap of the concentric cylinder or cone and plate. In order to reduce sHp, roughened walls should be used for the platens an alternative method would be to use a vane rheometer. 

From R D to quality control, rheology measurements for each phase of the product development life cycle involve raw materials, premixes, solutions, dispersions, emulsions, and full formulations. Well-equipped laboratories with stress- and strain-controlled oscillatory/steady shear rheometers and viscometers can generally satisfy most characterization needs. When necessary, customized systems are designed to simulate specific user or process conditions. Rheology measurements are also coupled with optic, thermal, dielectric, and other analytical methods to further probe the internal microstucture of surfactant systems. New commercial and research developments are briefly discussed in the following sections. 

FIG. 4.22 Schematic of biconical tool for surface rheology measurements using the Paar Physica interfacial rheometer. (Courtesy of American Institute of Physics.)... 

Rheological and Tensile Properties. Melt rheological measurements were made on an Instron Capillary Rheometer (0.993" L X 0.05014" D) at a temperature of 200°C and at various shear rates corresponding to crosshead speeds of from 0.005 in./min to 20 in./min. Measurements were also made with an Instron TM Model (0.05034" D X 1.0074" L) at 200°C and at various shear rates corresponding to crosshead speeds of from 0.006 in./min to 10 in./min. 

Rheological measurements were performed in shear using a stress controlled rheometer (Carri-Med CSL 100) operating in cone-plate geometry. Each sample is submitted successively to a first frequency sweep in range 10 3-40 Hz under 3% strain, to a creep and recovery test, and finally to a second frequency sweep identical to the first one. The dynamical strain amplitude (3%) and the value of the creep stress (chosen so as to keep the maximum strain below 10%) were set in order to remain within the linear viscoelasticity domain. Creep and creep recovery were recorded during 20 h and 80 h, respectively, times which allowed the steady state to be reached in all cases. A fresh sample was used for each solvent/temperature combination. 

The viscosity of the suspension at difierent biomass concentration was measured by Modular Compact Rheometer Physica MCR 300 (Paar-Physica). Controlled shear-stress measurements were done using the concentric cylinder system with a FL 100/6W impeller at temperatures of 30, 40, and 50 °C. Samples were mixed before measurements were taken. Then, an appropriate volume was placed into the viscometer, allowing several minutes for the temperature to stabilize. The rheological measurements were performed three times for each value of biomass concentration using a fresh sample each time. 

Rheological measurements were performed by using a rheometer MCR 300 (Anton Paar, Germany) with a Couette CelL... 

Rheological measurements of the silica suspensions were performed using a Paar Physica MCR300 rheometer with a cone-plate geometry. 

Mixes of S13TMSx and T30TMSx silylated silicas and a silicone oil (Wacker-Chemie AKIOOO) were submitted to dynamic rheological measurements using an oscillating cone/plane rheometer. In Fig. 14, the evolution of the viscosity, measured at 25°C and 0.278 Hz, with the silica surface coverage ratio is shown. 

---