Resist to substrate

Poly(vinylidene chloride). Poly(viayHdene chloride) [9002-85-1] (PVDC), most of which is produced by Dow Chemical, is best known in its saran or PVC-copolymerized form (see Vinylidene chloride and poly(VINYLIDENE chloride)). As solvent or emulsion coating, PVDC imparts high oxygen, fat, aroma, and water-vapor resistance to substrates such as ceUophane, oriented polypropylene, polyester, and nylon. 

Calculated values of Ef for several values of CAt/Km are shown in Figure 7.5, where Ef is seen to increase with increasing values of CAh/Km. When the values of CAh/Km approach zero, the curve approaches the first-order curve shown in Figure 7.4. The values of Ef decrease with increasing reaction rate and/or immobilized enzyme concentration, and also with increasing resistance to substrate mass transfer. 

A decrease in hydrostatic pressure along the fiber due to resistance to substrate solution flow occurs so that at a definite distance from the inlet, say Lc, transmembrane pressure is nil. Fiber-to-shell solution flux from that point on is negative and becomes a shell-to-fiber flux. Neglecting the shell pressure drop, the overall fiber-to-shell ultrafiltration net flow rate can then be obtained upon integration of the flux equation over the length of the fiber from the inlet to Lc, that is ... 

Finish systems can be one coat or multicoat that use primers, intermediate coats, and topcoats. Primers provide adhesion, corrosion protection, passivation, and solvent resistance to substrates. Topcoats provide weather, chemical, and physical resistance, and generally... 

A potential problem associated with adding a support material on the membrane surface is the resistance to substrate diffusion caused by the additional layer and the biofilm growing inside it. Further research is necessary to elucidate whether the advantages of retaining a larger amount of biomass outweigh the disadvantages with increased diffusional resistance for specific applications. 

Cementitious coatings provide corrosion resistance to substrates such as steel by maintaining the pH at the metal/coating interface above 4, a pH range where steel corrodes at a low rate. The proper selection of materials and their application is necessary if the coating is to be effective. To select the proper material, it is necessary to define the problem ... 

Aluminum. Some manufacturers also have WORM disks above 5.25 in. on offer with aluminum as substrate material. Eor A1 the same advantages apply as for glass with the exception of a high coefficient of thermal expansion and lacking resistance to aggressive chemical vapors and Hquids. 

For substrates of WORM and EOD(PCR) disks the industry in the future wants polymers that have a markedly improved resistance to heat softening compared to BPA-PC and, if possible, a lower water absorption and lower birefringence, but otherwise maintain the good characteristics in toughness, production, and cost (194). This goal is being approached in different ways further modification of BPA-PC, newly developed polymers, improvement of the processing characteristics of uv-curable cross-linked polymers, and development of special copolymers and polymer blends, eg,... 

Poly(methyl methacrylate). PMMA offers distinct advantages over BPA-PC with respect to significandy lower birefringence, higher modulus, and lower costs, but has not been successhil as a material for audio CDs and CD-ROM as well as a substrate material for WORM and EOD disks because of its high water absorption (which makes it prone to warp) and its unsuitabiUty for metallising, and less so because of its low resistance to... 

Special, uv-curable epoxy resins (qv) for substrate disks for optical data storage (Sumitomo BakeHte, Toshiba) excel by means of their very low birefringence (<5 nm/mm) and high Young s modulus. Resistance to heat softening and water absorption are similar to BPA-PC, but impact resistance is as low as that of PMMA. 

Other Polymers. Besides polycarbonates, poly(methyl methacrylate)s, cycfic polyolefins, and uv-curable cross-linked polymers, a host of other polymers have been examined for their suitabiUty as substrate materials for optical data storage, preferably compact disks, in the last years. These polymers have not gained commercial importance polystyrene (PS), poly(vinyl chloride) (PVC), cellulose acetobutyrate (CAB), bis(diallylpolycarbonate) (BDPC), poly(ethylene terephthalate) (PET), styrene—acrylonitrile copolymers (SAN), poly(vinyl acetate) (PVAC), and for substrates with high resistance to heat softening, polysulfones (PSU) and polyimides (PI). 

The properties of leather-like materials depend on the polymer used for substrate and coating layer. Feel, hand, and resistance to grain break are affected by the constmction. The polymers and constmctions of leather-like materials are shown in Table 1. Physical properties of leather and leather-like materials are shown in Table 2. 

In the wet system, manufacture proceeds as foUows (/) a 7—20% polyurethane solution of DMF is appHed onto a fabric and immersed in water containing 0—10% of DMF for coagulation (2) the coated fabric is washed and dried (4) the surface is finished by the dry system. For the substrate, a woven or knit fabric which has been bmshed on its surface is often used to improve appearance, resistance to grain break, and feel. 

The main cause of anode wear is electrochemical oxidation or sulfur attack of anodic surfaces. As copper is not sufficiently resistant to this type of attack, thin caps of oxidation and sulfur-resistant material, such as platinum, are bra2ed to the surface, as shown in Eigure 15a. The thick platinum reinforcement at the upstream corner protects against excessive erosion where Hall effect-induced current concentrations occur, and the interelectrode cap protects the upstream edge from anodic corrosion caused by interelectrode current leakage. The tungsten undedayment protects the copper substrate in case the platinum cladding fails. 

Properties desired in cable insulation and flexible circuit substrate materials include mechanical flexibiUty, fatigue endurance, and resistance to chemicals, water absorption, and abrasion. Both thermoplasts and thermosets are used as cable-insulating materials. Thermoplastic materials possess excellent electrical characteristics and are available at relatively low cost. 

Adhesion Life. A second key factor in determining the durabHity of a sealant is the abHity of the sealant to adhere to the substrate through its lifetime. A sealant may have exceHent resistance to uv effects, but if it has poor adhesion performance and faHs adhesively, it is of Httie use. The same can be said of a sealant with superior adhesion characteristics but poor resistance to uv. Either situation results in a short performance life. 

Pressure-Sensitive Adhesives. SiHcoae PSAs are used primarily ia specialty tape appHcatioas that require the superior properties of siHcoaes, including resistance to harsh chemical environments and temperature extremes (398,399). SiHcone PSAs are also used ia appHcatioas requiring long service Hfe, electrical iasulatioa, and protection from moisture. Another distinctive advantage of siHcone PSAs is their abiHty to wet low surface energy tape substrates such as PTEE. 

In the 3M Water/Alcohol Drop Test (41), this test is designed to provide a simple, rapid method to assess the aqueous stain resistance of substrates treated with a protective finish. 

---