Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Vapor residence time

Increasing the pressure of irreversible vapor-phase reactions increases the rate of reaction and hence decreases reactor volume both by decreasing the residence time required for a given reactor conversion and increasing the vapor density. In general, pressure has little effect on the rate of liquid-phase reactions. [Pg.43]

A twin-screw extmder is used to reduce residual monomers from ca 50 to 0.6%, at 170°C and 3 kPa with a residence time of 2 min (94). In another design, a heated casing encloses the vented devolatilization chamber, which encloses a rotating shaft with specially designed blades (99,100). These continuously regenerate a large surface area to faciUtate the efficient vaporization of monomers. The devolatilization equipment used for the production of polystyrene and ABS is generally suitable for SAN production. [Pg.195]

Both vapor-phase and Hquid-phase processes are employed to nitrate paraffins, using either HNO or NO2. The nitrations occur by means of free-radical steps, and sufftciendy high temperatures are required to produce free radicals to initiate the reaction steps. For Hquid-phase nitrations, temperatures of about 150—200°C are usually required, whereas gas-phase nitrations fall in the 200—440°C range. Sufficient pressures are needed for the Hquid-phase processes to maintain the reactants and products as Hquids. Residence times of several minutes are commonly required to obtain acceptable conversions. Gas-phase nitrations occur at atmospheric pressure, but pressures of 0.8—1.2 MPa (8—12 atm) are frequentiy employed in industrial units. The higher pressures expedite the condensation and recovery of the nitroparaffin products when cooling water is employed to cool the product gas stream leaving the reactor (see Nitroparaffins). [Pg.35]

Any refractory material that does not decompose or vaporize can be used for melt spraying. Particles do not coalesce within the spray. The temperature of the particles and the extent to which they melt depend on the flame temperature, which can be controlled by the fueLoxidizer ratio or electrical input, gas flow rate, residence time of the particle in the heat zone, the particle-size distribution of the powders, and the melting point and thermal conductivity of the particle. Quenching rates are very high, and the time required for the molten particle to soHdify after impingement is typically to... [Pg.45]

Dilute (1—3%), chloride-containing solutions of either HOCl, hypochlorite, or aqueous base, can be stripped in a column against a current of CI2, steam, and air at 95—100°C and the vapors condensed giving virtually chloride-free HOCl solutions of higher concentration in yields as high as 90% (122—124). Distillation of more concentrated solutions requires reduced pressure, lower temperature, and shorter residence times to offset the increased decomposition rates. [Pg.468]

Reaction Conditions. Typical iadustrial practice of this reaction involves mixing vapor-phase propylene and vapor-phase chlorine in a static mixer, foEowed immediately by passing the admixed reactants into a reactor vessel that operates at 69—240 kPa (10—35 psig) and permits virtual complete chlorine conversion, which requires 1—4 s residence time. The overaE reactions are aE highly exothermic and as the reaction proceeds, usuaEy adiabaticaEy, the temperature rises. OptimaEy, the reaction temperature should not exceed 510°C since, above this temperature, pyrolysis of the chlorinated hydrocarbons results in decreased yield and excessive coke formation (27). [Pg.33]

Process development of the use of hydrogen as a radical quenching agent for the primary pyrolysis was conducted (37). This process was carried out in a fluidized-bed reactor at pressures from 3.7 to 6.9 MPa (540—1000 psi), and a temperature of 566°C. The pyrolysis reactor was designed to minimize vapor residence time in order to prevent cracking of coal volatiles, thus maximizing yield of tars. Average residence times for gas and soHds were quoted as 25 seconds and 5—10 rninutes. A typical yield stmcture for hydropyrolysis of a subbiturninous coal at 6.9 MPa (1000 psi) total pressure was char 38.4, oil... [Pg.287]

Tubular reactors have been the main tools to study continuous flow processes for vapor or gas-phase reactions. These are also used for reaction in tv o flowing phases over a solid catalyst. When the catalyst is in a fixed bed, the contact between the liquid on the outside surface of the particulate is uncertain. For slurry-type solid catalyst the residence time of the catalyst or the quantity in the reactor volume can be undefined. [Pg.31]

This method uses the separation factor given in the section titled Vapor Residence Time. The first three steps use equations and a graph (or alternate equation) in that section to get Kv and Uvapormax- Nomenclature is explained there. [Pg.133]

Measurements of the true reaction times are sometimes difficult to determine due to the two-phase nature of the fluid reactants in contact with the solid phase. Adsorption of reactants on the catalyst surface can result in catalyst-reactant contact times that are different from the fluid dynamic residence times. Additionally, different velocities between the vapor, liquid, and solid phases must be considered when measuring reaction times. Various laboratory reactors and their limitations for industrial use are reviewed below. [Pg.244]

The key to efficient destruction of liquid hazardous wastes lies in minimizing unevaporated droplets and unrcacted vapors. Just as for the rotary kiln, temperature, residence time, and turbulence may be optimized to increase destruction efficiencies. Typical combustion chamber residence time and temperature ranges arc 0.5-2 s and 1300-3000°F. Liquid injection incinerators vary in dimensions and have feed rates up to 1500 gal/h of organic wastes and 4000 gal/h of aqueous waste. [Pg.155]


See other pages where Vapor residence time is mentioned: [Pg.430]    [Pg.430]    [Pg.430]    [Pg.514]    [Pg.9376]    [Pg.385]    [Pg.47]    [Pg.430]    [Pg.430]    [Pg.430]    [Pg.514]    [Pg.9376]    [Pg.385]    [Pg.47]    [Pg.69]    [Pg.417]    [Pg.389]    [Pg.268]    [Pg.47]    [Pg.342]    [Pg.389]    [Pg.487]    [Pg.233]    [Pg.263]    [Pg.43]    [Pg.419]    [Pg.483]    [Pg.412]    [Pg.169]    [Pg.460]    [Pg.474]    [Pg.1139]    [Pg.1590]    [Pg.39]    [Pg.128]    [Pg.145]    [Pg.74]    [Pg.130]    [Pg.132]    [Pg.103]    [Pg.230]    [Pg.233]    [Pg.218]   
See also in sourсe #XX -- [ Pg.236 ]




SEARCH



© 2024 chempedia.info