Reactions with acids strength

Organic Reactions. Nitric acid is used extensively ia iadustry to nitrate aHphatic and aromatic compounds (21). In many iastances nitration requires the use of sulfuric acid as a dehydrating agent or catalyst the extent of nitration achieved depends on the concentration of nitric and sulfuric acids used. This is of iadustrial importance ia the manufacture of nitrobenzene and dinitrotoluene, which are iatermediates ia the manufacture of polyurethanes. Trinitrotoluene (TNT) is an explosive. Various isomers of mononitrotoluene are used to make optical brighteners, herbicides (qv), and iasecticides. Such nitrations are generally attributed to the presence of the nitronium ion, NO2, the concentration of which iacreases with acid strength (see Nitration). 

Phenomenologically, the reactions between reduced forms of [S2Moi8062]" and li+ are analogous to those with H+, with acidity strength being in the order HCIO4 > liClOr > H2O. However, as this simulation involves a significant number of unknown parameters, the coherent set of data obtained cannot be assumed to be unique. 

The reaction yield increases with acid strength, further suggesting the intermediacy of the protosolvated, superelectrophilic formylating species (9). 

To illustrate the effect of ionic strength on degradation of calcium carbonate we have calculated the solubility of calcium carbonate in deionized water, acid at pH = 4.0 and acid rain at pH = 4.0 with an ionic strength of 7.2 x 10 in the absence of CO2. The results of these calculations are shown in Table 2 and are plotted in Figure 3. These data show that the ionic strength contribution of sea spray and other atmospheric sources are as significant as the neutralization reaction with acid at pH = 4.0 in the degradation of coquina by acid rainfall. 

Acylation of amines by anhydrides may show autocatalytic behaviour. Thus the reaction of various amines with anhydrides in benzene is catalysed by the monomeric form of the acid produced . Litvinenko has suggested that the catalytic effect is due to complex formation (7 or 8) and the catalytic power of the carboxylic acid increases with acid strength until protonation of the amine occurs. Similar complexes have been proposed for the add-catalysed acylation... 

Reaction with Chlorine. Polyacrylamide reacts with chlorine under acid conditions to form reasonably stable A/-chloroamides. The polymers are water soluble and can provide good wet strength and wet web strength in paper (60). 

The most important appHcation of metal alkoxides in reactions of the Friedel-Crafts type is that of aluminum phenoxide as a catalyst in phenol alkylation (205). Phenol is sufficientiy acidic to react with aluminum with the formation of (CgH O)2Al. Aluminum phenoxide, when dissolved in phenol, greatiy increases the acidic strength. It is beheved that, similar to alkoxoacids (206) an aluminum phenoxoacid is formed, which is a strong conjugate acid of the type HAl(OCgH )4. This acid is then the catalyticaHy active species (see Alkoxides, metal). 

Because they are weak acids or bases, the iadicators may affect the pH of the sample, especially ia the case of a poorly buffered solution. Variations in the ionic strength or solvent composition, or both, also can produce large uncertainties in pH measurements, presumably caused by changes in the equihbria of the indicator species. Specific chemical reactions also may occur between solutes in the sample and the indicator species to produce appreciable pH errors. Examples of such interferences include binding of the indicator forms by proteins and colloidal substances and direct reaction with sample components, eg, oxidising agents and heavy-metal ions. 

Equation 20 is the rate-controlling step. The reaction rate of the hydrophobes decreases in the order primary alcohols > phenols > carboxylic acids (84). With alkylphenols and carboxylates, buildup of polyadducts begins after the starting material has been completely converted to the monoadduct, reflecting the increased acid strengths of these hydrophobes over the alcohols. Polymerization continues until all ethylene oxide has reacted. Beyond formation of the monoadduct, reactivity is essentially independent of chain length. The effectiveness of ethoxylation catalysts increases with base strength. In practice, ratios of 0.005—0.05 1 mol of NaOH, KOH, or NaOCH to alcohol are frequendy used. 

The other analytical methods necessary to control the typical specification given in Table 5 are, for the most part, common quality-control procedures. When a chemical analysis for purity is desired, acetylation or phthalation procedures are commonly employed. In these cases, the alcohol reacts with a measured volume of either acetic or phthalic anhydride in pyridine solution. The loss in titratable acidity in the anhydride solution is a direct measure of the hydroxyl groups reacting in the sample. These procedures are generally free from interference by other functional groups, but both are affected adversely by the presence of excessive water, as this depletes the anhydride reagent strength to a level below that necessary to ensure complete reaction with the alcohol. Both procedures can be adapted to a semimicro- or even microscale deterrnination. 

Adolph Baeyer is credited with the first recognition of the general nature of the reaction between phenols and aldehydes in 1872 ([2,5-7] [18], Table 5.1). He reported formation of colorless resins when acidic solutions of pyrogallic acid or resorcinol were mixed with oil of bitter almonds, which consists primarily benzaldehyde. Baeyer also saw resin formation with acidic and basic solutions of phenol and acetaldehyde or chloral. Michael and Comey furthered Baeyer s work with additional studies on the behavior of benzaldehyde and phenols [2,19]. They studied a variety of acidic and basic catalysts and noted that reaction vigor followed the acid or base strength of the catalyst. Michael et al. also reported rapid oxidation and darkening of phenolic resins when catalyzed by alkaline materials. 

---