Rays s. Irradiation

Radziszewski reaction 24, 204s31 Raney catalysts s. Nidcel Rays s. Irradiation Reaction gas chromatography 24, 501S31... 

Raney catalysts s. Nickel Rays s. Irradiation Reaction, terminal s. w-Halogenation -, transannular s. Transannular... 

Mutation. For industrial appHcations, mutations are induced by x-rays, uv irradiation or chemicals (iiitrosoguanidine, EMS, MMS, etc). Mutant selections based on amino acid or nucleotide base analogue resistance or treatment with Nystatin or 2-deoxyglucose to select auxotrophs or temperature-sensitive mutations are easily carried out. Examples of useful mutants are strains of Candida membranefaciens, which produce L-threonine Hansenu/a anomala, which produces tryptophan or strains of Candida lipolytica that produce citric acid. An auxotrophic mutant of S. cerevisiae that requires leucine for growth has been produced for use in wine fermentations (see also Wine). This yeast produces only minimal quantities of isoamyl alcohol, a fusel oil fraction derived from leucine by the Ehrlich reaction (10,11). A mutant strain of bakers yeast with cold-sensitive metaboHsm shows increased stabiUty and has been marketed in Japan for use in doughs stored in the refrigerator (12). 

First, if a capillary cell is used, the X-ray beam size by default has to be small—at least in the vertical direction. So, if the experiments are conducted on a nonfocused beam line then the X-ray flux irradiating the sample is lower and this will degrade the signal/noise ratio (S/N). Typically in the pressed-wafer cell designs the size of the wafer is large to allow a large X-ray beam size to be used. 

Neutron Activation Analysis Few samples of interest are naturally radioactive. For many elements, however, radioactivity may be induced by irradiating the sample with neutrons in a process called neutron activation analysis (NAA). The radioactive element formed by neutron activation decays to a stable isotope by emitting gamma rays and, if necessary, other nuclear particles. The rate of gamma-ray emission is proportional to the analyte s initial concentration in the sample. For example, when a sample containing nonradioactive 13AI is placed in a nuclear reactor and irradiated with neutrons, the following nuclear reaction results. 

As noted earlier, gamma-ray emission is measured following a cooling period in which short-lived interferents are allowed to decay away. The initial activity therefore, is determined by extrapolating a curve of activity versus time back to f = 0 (Figure 13.15). Alternatively, if the samples and standards are irradiated simultaneously, and the activities are measured at the same time, then these activities may be used in place of Aq) and (Ao)s in the preceding equations. 

Extraterrestrial dust particles can be proven to be nonterrestrial by a variety of methods, depending on the particle si2e. Unmelted particles have high helium. He, contents resulting from solar wind implantation. In 10-)J.m particles the concentration approaches l/(cm g) at STP and the He He ratio is close to the solar value. Unmelted particles also often contain preserved tracks of solar cosmic rays that are seen in the electron microscope as randomly oriented linear dislocations in crystals. Eor larger particles other cosmic ray irradiation products such as Mn, Al, and Be can be detected. Most IDPs can be confidently distinguished from terrestrial materials by composition. Typical particles have elemental compositions that match solar abundances for most elements. TypicaUy these have chondritic compositions, and in descending order of abundance are composed of O, Mg, Si, Ee, C, S, Al, Ca, Ni, Na, Cr, Mn, and Ti. 

The physical techniques used in IC analysis all employ some type of primary analytical beam to irradiate a substrate and interact with the substrate s physical or chemical properties, producing a secondary effect that is measured and interpreted. The three most commonly used analytical beams are electron, ion, and photon x-ray beams. Each combination of primary irradiation and secondary effect defines a specific analytical technique. The IC substrate properties that are most frequendy analyzed include size, elemental and compositional identification, topology, morphology, lateral and depth resolution of surface features or implantation profiles, and film thickness and conformance. A summary of commonly used analytical techniques for VLSI technology can be found in Table 3. 

Irradiation. Although no irradiation systems for pasteurization have been approved by the U.S. Food and Dmg Administration, milk can be pasteurized or sterilized by P tays produced by an electron accelerator or y-rays produced by cobalt-60. Bacteria and enzymes in milk are more resistant to irradiation than higher life forms. For pasteurization, 5000—7500 Gy (500,000—750,000 tad) are requited, and for inactivating enzymes at least 20,000 Gy (2,000,000 rad). Much lower radiation, about 70 Gy (7000 tad), causes an off-flavor. A combination of heat treatment and irradiation may prove to be the most acceptable approach. 

X-Ray Fluorescence (XRF) is a nondestructive method used for elemental analysis of materials. An X-ray source is used to irradiate the specimen and to cause the elements in the specimen to emit (or fluoresce) their characteristic X rays. A detector s)rstem is used to measure the positions of the fluorescent X-ray peaks for qualitative identiflcation of the elements present, and to measure the intensities of the peaks for quantitative determination of the composition. All elements but low-Z elements—H, He, and Li—can be routinely analyzed by XRF. 

The method involves the irradiation of a sample with polychromatic X-rays (synchrotron radiation) which inter alia promote electrons from the innermost Is level of the sulfur atom to the lowest unoccupied molecular orbitals. In the present case these are the S-S antibonding ct -MOs. The intensity of the absorption lines resulting from these electronic excitations are proportional to the number of such bonds in the molecule. Therefore, the spectra of sulfur compounds show significant differences in the positions and/or the relative intensities of the absorption lines [215, 220, 221]. In principle, solid, liquid and gaseous samples can be measured. 

A few methods produce reactive molecules by reactions in solid matrices. The most widely used consists of irradiating already isolated precursors with UV light (including vacuum UV light at A < 200 nm), y- or X-rays. In this case, the fragments which are formed as products of the precursor s dissociation must not recombine in the matrix site. To achieve this effect, one of the fragments should be either chemically inactive [e.g. N2, CO2 see (la)] or able to diffuse easily from the site [e.g. hydrogen atoms as in (lb)]. 

X-Ray irradiation of quartz or silica particles induces an electron-trap lattice defect accompanied by a parallel increase in cytotoxicity (Davies, 1968). Aluminosilicate zeolites and clays (Laszlo, 1987) have been shown by electron spin resonance (e.s.r.) studies to involve free-radical intermediates in their catalytic activity. Generation of free radicals in solids may also occur by physical scission of chemical bonds and the consequent formation of dangling bonds , as exemplified by the freshly fractured theory of silicosis (Wright, 1950 Fubini et al., 1991). The entrapment of long-lived metastable free radicals has been shown to occur in the tar of cigarette smoke (Pryor, 1987). 

E.s.r. showed that, X. ray irradiation of tetraalkyldiphosphine diphosphides gave phosphoranyl radicals with t.b.p. structures (39).114 A structure has been assigned to phosphiny1hydrazy1s (40). The dimethy1 ami no radical was particularly persistent.115 The e.s.r. parameters of the electrogenerated pyrazine radical cations (41) have been recorded.116 The spectra of a stable furanyl phosphate radical adduct117 and a phenalene radical anion which involves injection of spin density into half an attached cyclophosphazene ring,11 are reported. 

---