Powder electronic drying

The process starts with the preparation of polymer solutions, for instance, polyvinyl alcohol (PVA), and metal compounds, for instance, 3d-metal chlorides. Afterwards, the solutions with a certain concentration are mixed in the ratio PVA-metal chloride equals to 20 1-1 5 (better 5 1). Then the prepared solutions are dried till they obtain gel-like colored films with further temperature elevation up to 100°C. The films obtained are controlled by spectral photometry, and also with help of transmission optical microscopy, atomic force microscopy and X-ray photoelectron spectroscopy. When the film color changes to black, the films are heated in the furnace according to the following program 100-200-300-400°C. As a result, the dark porous semiproduct with many microcracks is formed, that is milled in spherical or jet mill. The nanopowder obtained is steamed and dispersed in hot water. After filtration, the powder is dried and tested with the help of Raman spectroscopy. X-ray photoelectron spectroscopy, transmission electron microscopy and electron microdiffraction. 

Small, complex-shaped glass articles such as thread guides for the textile industry and television gun mounts for the electronics industry are made by the multiform process. The dry-milled powder is mixed with an inorganic binder and a fluid vehicle, and then atomi2ed by a spray dryer into small, dried agglomerates of glass powder and binder with good flow characteristics. They are subsequently pressed to the desired shape and fired. 

FIGURE 5.3 Electron micrographs of whey protein isolate (WPI). Scanning electron microscopy of dry WPI powder (A). Transmission electron microscopy of WPI stained with uranyl acetate (B) nonextruded WPI Paste (40% moisture) and (C) extruded texturized WPI (100 °C, 40% moisture) (Onwulata et ai, 2003a). 

Boujday, S., Wiinsch, F., Portes, P., Bocquet, J.F., and Colbeau-Justin, C. (2004) Photocatalytic and electronic properties of Ti02 powders elaborated by sol-gel route and supercritical drying. Solar Energy Materials ej Solar Cells, 83 (4), 421-433. 

The structure of the metal particles dispersed on a silica powder support ( Aerosil 380, 70 A average silica particle diameter) has been studied by Avery and Sanders (47) using electron microscopy in both bright and dark field, to determine the extent to which the metal particles were multiply twinned or of ideal structure. Platinum, palladium, and gold were examined. These catalysts were prepared by impregnation using an aqueous solution of metal halide derivatives, were dried at 100°-150°C, and were hydrogen... 

High resolution transmission electron microscopy (HRTEM) micrographies were performed with a JEOL JEM-3010 microscope operating at 300 kV (Cs= 0.6 mm, point resolution 1.7 A). Images were recorded with CCD camera (MultiScan model 794, Gatan, 1024 x 1024 pixels, pixel size 24 x 24 pm2). The powder samples were mixed in ethanol and then ultrasonicated for 10 min. A drop of the wet sample was placed on a copper grid and then allowed to dry for 10 min before TEM analysis. 

DPB as well as other DPP molecules (t-stilbene, diphenyl-hexatriene) with relatively low ionization potential (7.4-7.8 eV) and low vapor pressure was successfully incorporated in the straight channel of acidic ZSM-5 zeolite. DPP lies in the intersection of straight channel and zigzag channel in the vicinity of proton in close proximity of Al framework atom. The mere exposure of DPP powder to Bronsted acidic ZSM-5 crystallites under dry and inert atmosphere induced a sequence of reactions that takes place during more than 1 year to reach a stable system which is characterized by the molecule in its neutral form adsorbed in the channel zeolite. Spontaneous ionization that is first observed is followed by the radical cation recombination according to two paths. The characterization of this phenomenon shows that the ejected electron is localized near the Al framework atom. The reversibility of the spontaneous ionization is highlighted by the recombination of the radical cation or the electron-hole pair. The availability of the ejected electron shows that ionization does not proceed as a simple oxidation but stands for a real charge separated state. 

The electron-deficient alkene (5.2 mmol) in MeCN (5 ml) is added to an intimate mixture of powdered K2C03 (1 g) and NaOH (0.2 g), the (S)-menthone-protected ethyl glycine (1.27 g, 5 mmol), and TBA-Br (0.16 g, 0.5 mmol) in MeCN (20 ml). The mixture is stirred for 1 h at 0°C and then filtered. The solid is washed with MeCN (10 ml) and the combined organic solutions are evaporated and the residue is taken up in Et20. The ethereal solution is washed well with H20, dried (MgS04), and evaporated to produce the alkylated imine, which can be converted into the amino acid upon hydrolysis with aqueous acid. 

---